Atdec AWMS-2-D13-F User manual

AWMS-2-D13-F Page 1 of 7
Installation Guide
AWMS-2-D13-F
Dual Dynamic Arm Mount F clamp
COMPONENT CHECKLIST RANGE
AWM-LC
Channel
Clamp
(x2)
• Phillips Head
Screwdriver
REQUIRED TOOLS
AWM-AD
Dynamic
Arm
(x2)
AWM-FF
F Clamp
(x1)
AWM-P13
135 Post
(x1)
CONTENTS
F Clamp
Page 2
135 Post
Page 3
Channel Clamp
Page 4
Dynamic Arm
Page 5
AWM-FF
Component Checklist + Clamp Installation
AWM-P13
Component Checklist + Post Installation
AWM-LC
Component Checklist + Clamp Installation
AWM-AD
Component Checklist + Arm Installation
May be supplied as:
AWM-ADC
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove/ throw away the plastic cap on channel clamp and arm links.
! This product is compatible with Atdec AWM Series products.
! Product must only be installed on a solid work surface capable of supporting the weight of all equipment being mounted.
! Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed
the capacity of the mount even though the monitor weight may be within the stated range.
! The manufacturer accepts no responsibility for incorrect installation.

AWMS-2-D13-F Page 2 of 7
AWM-FF
F Clamp
1. Attach post to upper clamp
Fasteners
supplied
with post
NOTE: Post packaged separately.
2. Attach lower clamp to upper clamp
2.1 Measure the
worksurface thickness
and choose the suitable
lower clamp position.
2.3 Attach lower clamp to upper
clamp in the suitable position
using the two provided screws.
(Normal position shown here)
A B
A B
A - Normal
0 - 36mm
(0.00 - 1 ”)
A B
B - Inverted
36 - 79mm
(1 ” - 3”) Note: If there is only a small gap
behind the worksurface, perform
Step 3.1 before this step.
2.2 If using inverted
position change
the screw direction
of the lower clamp.
3. Fit xing to work surface
3.1 Place in desired location
on worksurface
3.2 Screw in
pressure plate and
tighten rmly.
5mm
Hex Key
Mounting
surface
COMPONENT CHECKLIST
D
5mm
Hex Key (x1)
A
Upper Clamp
(x1)
B
Lower Clamp
(x1)
C
Screw
M8 x 16mm (x2)

AWMS-2-D13-F Page 3 of 7
AWM-P
Post
COMPONENT CHECKLIST
A
Post
(x1)
C
Screw
M8
(x2)
B
Post Cap
(x1)
D
Cable Cover Cap
(x2)
3. Position Cable Cover and t Post Cap
3.1 To reposition the cable cover, pull it straight up and out
of the post and insert it into any of the available channels
3.2 Fit post cap onto the top of the post
SQUEEZE
SQUEEZE
SQUEEZE
SQUEEZE
Optional cable
cover positions
Hex Key
(Supplied w/xing)
Post
Post Cap
NOTE: An hex key
may be stored in
the Post Cap.
1. Attach Post to Fixing
FC
C Clamp
FB
Bolt
Through
Kit
AC-GC
Grommet
Clamp
FH
HD F Clamp
FF
F Clamp
Also Compatible
All AWM series desk xings including:
AWM-FC, AWM-FB, AC-GC and AWM-FH
1.1 Follow the F Clamp installation guide
on pages 2 of this booklet or provided
with your alternate xing option.
2. Mount Clamp to Post
2.2 Do not mount monitor
arm on rear channel post
when using the supplied F
Clamp
2.1 Slide clamp into post and
position to desired height. Turn
knob to lock in place.
If you are installing multiple mounts,
use the guide marks on post as
reference for setting the height of
each arm. Final ne-tuning may be
required once monitor is installed.
NOTE: Guide marks only available on
400 post, 510 post and 750 post.
4. Cable clips and cover
PUSH
4.1 Push the cable down
into the cable clip.
4.2 Insert one
side of the cable
clip into the
channel on the
post assembly,
then push
in the other side.
4.4 Feed
remaining
cable into
the cover.
Load cables
into cable
cover
4.3 Loop
cable and
insert into
cable cover.
Cables can
exit from the
side of the
cable cover
PUSH
PUSH
Supplied
F Clamp
AWM-FF
A B

AWMS-2-D13-F Page 4 of 7
AWM-LC
Channel Clamp
COMPONENT CHECKLIST
A
Channel
Clamp
(x1)
1. Fix Clamp to Post
1.1 Ensure knob is undone. 1.2 Slide Channel Clamp into channel.
Push knob to
aid insertion
1.3 Hold clamp in desired position on post
and turn knob to lock in place.
1. Ensure Knob is undone
Tip: push knob
to aid insertion
2. Slide post clamp into channel
3. Hold clamp in desired position on post and turn
knob to lock in place
2. (Optional) Set arm rotation to 180°
NOTE: default arm rotation is set to rotate 360°
2.1 Remove plastic sleeve. 2.2 Remove rotation ring 2.3 Place rotation ring in the desired position and replace plastic sleeve.
NOTE: Place the rotation ring
depending on what post channel
the arm will be attached to. The tag
should always face towards the user.
1. Remove plastic sleeve
2. Remove rotation ring
1. Press
2. Lift
3. Place the rotation ring
in the desired postion
180°
360°
OR
Default
Position
Flipped
Position
Tag
WEIGHT RANGE
0 - 14kg
(0 - 31lbs)
NOTE: Do not remove/
throw away plastic cap
on channel clamp.

AWMS-2-D13-F Page 5 of 7
AWM-AD
Dynamic Arm
COMPONENT CHECKLIST
Monitor weight should be within the weight
range of all modular elements that make up
the complete monitor mounting solution.
WEIGHT RANGE
Flat Monitors
0 - 9kg
(0 - 20lbs)
Curved Monitors
0 - 6kg
(0 - 13.5lbs)
1. Fit arm onto Channel Clamp
1.1 Push arm onto shaft. 1.2 Ensure arm is fully pushed onto shaft.
NOTE: Check the arm rotation is
smooth after tightening.
1.3 Tighten joint screw.
2. Attach VESA head to monitor
2.1 Check VESA mounting
compatibility.
100mm
75mm
100mm
75mm
NOTE: For other sizes, use
a suitable adaptor plate
(sold separately).
Flush
Too long Too short
Spacer
5mm 12mm
NOTE: Be sure to use a screw
length that suits the monitor.
2.2 Attach VESA head onto monitor with provided screws.
NOTE: Spacers may be required for curved, recessed or uneven monitor surfaces.
B
VESA
Head
(x1)
C
Screw
M4x25mm
(x4)
F
Spacer
(x4)
D
Screw
M4x16mm
(x4)
G
Security
Screw
(x1)
E
Screw
M4x12mm
(x4)
H
4mm
Hex Key
(x1)
A
Dynamic
Monitor Arm
(x1)

AWMS-2-D13-F Page 6 of 7
5. Adjust arm tension
5.1 To accurately set the tension of the arm,
position the monitor at 90 degrees
5.3 If the monitor sags or falls down,
increase the arm tension by rotating
the screw clockwise.
Heavier
Monitor
Lighter
Monitor
5.2 Use the hex key to adjust the arm tension to the weight
of the monitor. Follow steps 6.3 to 6.5 to set the tension.
Monitor Falls
(from top)
Increase Tension
5.5 If the monitor oats or hovers
in all positions the arm tension
is balanced and does not require
further adjustment.
Monitor ‘Floats’
(all positions)
Balanced
5.4 If the monitor springs upwards
from the bottom position, decrease
the arm tension by rotating the
screw anti-clockwise.
Monitor Springs
(from bottom)
Reduce Tension
90°
3. Mount monitor
4. Adjust tilt tension & Install security screw
Monitor arm
3.1 Insert VESA head into the
monitor arm.
3.3 Push the lever down to
secure it to the arm assembly.
3.2 Ensure that the VESA head sits
ush within the monitor arm. There
should be no gap.
Gap No gap
Tighten
Loosen
4.1 Use the provided Hex Key to adjust the tilt tension until
the monitor holds in a vertical position at the end of the arm.
NOTE: Support
monitor while adjusting
Tighten
Loosen
4.2 (OPTIONAL) To install the optional security
screw tilt the head upwards.

AWMS-2-D13-F Page 7 of 7
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20230119B
7. Cable management
6. Tension gauge
When installing
multiple
monitors of a
similar weight,
use the tension
gauge to make
installation faster.
1. Set up one monitor
and record the position
of the marker on
the gauge.
2. When installing
subsequent monitors,
pre-tension the arm to
the recorded amount,
then ne-tune the
tension by following
steps 5.3 to 5.5.
Arm Tension Gauge
Marker
7.1 Plug cables into the monitor
and route the cables down the arm
using the cable hooks and clips.
7.2 Wedge cable into the central
gap and slide it down the arm.
7.3 The cable should slip into the arm
cavity
7.4 Slide the remaining loose
cable from the central gap up
the arm.
See steps 7.2 to 7.4
Important!
Ensure enough cable slack is
given in this area to allow for
movement of the monitor.