Autel MaxiAP AP200M User manual

i
CONTENTS
1GENERAL INTRODUCTION ..........................................................................................1
FUNCTIONAL DESCRIPTION .................................................................................................1
TECHNICAL SPECIFICATIONS...............................................................................................2
WIRELESS COMMUNICATION ...............................................................................................3
POWER SOURCE ...............................................................................................................3
2GETTING STARTED ....................................................................................................4
POWERING UP..................................................................................................................4
FUNCTION BUTTONS ..........................................................................................................6
NAVIGATION BUTTONS .......................................................................................................7
3EOBD..............................................................................................................................8
GENERAL PROCEDURE.......................................................................................................8
EXITING DIAGNOSTICS......................................................................................................10
4DIAGNOSTICS.............................................................................................................12
NAVIGATION....................................................................................................................12
DIAGNOSIS......................................................................................................................14
5SERVICE......................................................................................................................17
OIL RESET SERVICE ........................................................................................................17
ELECTRONIC PARKING BRAKE (EPB) SERVICE...................................................................17
BATTERY MANAGEMENT SYSTEM (BMS) SERVICE..............................................................18
DIESEL PARTICULATE FILTER (DPF) SERVICE ....................................................................19
STEERING ANGLE SENSOR (SAS) SERVICE .......................................................................20
THROTTLE MATCH SERVICE..............................................................................................20
6HISTORY......................................................................................................................21
7REPAIR REPORTS......................................................................................................22
8MALL ............................................................................................................................23
PURCHASE VEHICLE DIAGNOSTIC DATA PACKAGE.................................................................23
9ME ................................................................................................................................25
ORDER MANAGER............................................................................................................25
DELETE VEHICLE .............................................................................................................25
DATA LOGGING................................................................................................................25
VCI CONNECTION............................................................................................................26

ii
VCI MANAGER ................................................................................................................26
SETTINGS .......................................................................................................................26
USER MANUAL ................................................................................................................26
10 PRODUCT TROUBLESHOOTING...............................................................................27
VEHICLE LINKING ERROR..................................................................................................27
11 WARRANTY AND SERVICE........................................................................................28
LIMITED ONE YEAR WARRANTY.........................................................................................28

1
1 General Introduction
The MaxiAP AP200M is an enhanced DIY vehicle diagnostic dongle with specialized
diagnostic and service functions. It scans all systems and performs 6 most common
service functions, including Oil Reset, EPB, SAS, BMS, DPF, and Throttle Match for all
vehicle makes and models. The MaxiAP AP200M turns your mobile device into an
advanced diagnostics and service tool.
The MaxiAP AP200M package includes a Bluetooth (BT) dongle and a MaxiAP200 app.
It is used to connect to a vehicle's OBDII port and connect with the Android or iOS device
for a complete line of your chosen brand. It is almost compatible with all vehicle models
of European, Asian, and U.S. vehicles, 1996 and newer.
Functional Description
1. Vehicle Data Connector (16-pin) –connects the MaxiAP AP200M to the vehicle's
16-pin OBDII port directly.
2. Power LED –indicates system status.
The power LED displays green, blue, and red depending on power level and operating
state.
A. Green
Lights solid green when the MaxiAP AP200M is plugged in and not connected
with the device.
B. Blue
Lights solid blue when the device is connected with the MaxiAP AP200M via
Bluetooth.
Figure 1-1 Product View

2
Flashes blue when the device is communicating with the MaxiAP AP200M, for
example, when the device is reading Engine DTCs.
C. Red
Lights solid red when the MaxiAPAP200M is updating the firmware or when the
update failed, or when the MaxiAP AP200M is locked.
Flashed red fast when the communication failed between the device and the
dongle via Bluetooth. Please restart the dongle until it works properly.
3. Strap Hole –attach the strap to the MaxiAPAP200M.
NOTE
When the MaxiAP AP200M has lost connection from the device for more than 10 minutes,
the LED goes off and the AP200M enters power saving standby mode. The power LED
will light when reconnected.
Technical Specifications
Table 1-1 Specifications
Item
Description
Communications
BL 4.2 Dual-Mode
Wireless Frequency
2.4 GHz
Input Voltage Range
9 VDC to 26 VDC
Supply Current
100 mA@12 V
Sleep Mode Current
3 mA@12 V
Operating Temp.
0°C to 50°C
Storage Temp.
-20°C to 70°C
Dimensions (L*W*H)
59 mm (2.32'') * 44 mm (1.73'') * 21.5mm (0.85'')
Weight
32.1g (0.07 lb.)

3
Wireless Communication
The MaxiAP AP200M uses BT communication. It can transmit vehicle data to your
Android or iOS device. The working range for BT communication is about 33 feet (about
10 m). Signal lost due to moving out of range will automatically be restored once the
device is brought within transmission range to the MaxiAP AP200M connector.
Power Source
The MaxiAP AP200M operates on 12-volt vehicle power that it receives through the
vehicle data connection port. The unit powers on whenever it is connected to an OBDII/
EOBD compliant data link connector (DLC).

4
2 Getting Started
NOTE
The images and illustrations depicted in this manual may differ slightly from the actual
ones. The user interfaces for iOS & Android devices might be slightly different. This
manual uses UI for iOS devices as an example.
Powering Up
1. Download & install app
Scan the QR code or search for MaxiAP200 in App Store or Google Play to
download and install the app to your device.
2. Register & log in
Open the MaxiAP200 app and tap Register near the top right of the screen.
Follow the on-screen instructions to complete the registration.
Log in with your registered email address and password.
3. Bind VCI with device
On the Bind VCI interface, scan the QR code imprinted on the Bluetooth dongle to
automatically retrieve the serial number. Ensure the email information is correct. Tap
Bind to pair dongle with device.
4. Purchase & install software
Tap Mall below the list to purchase and install the software selected. Full OBDII
functions included at no charge. One vehicle-line is included free through Mall after
successfully pairing the dongle for the first time (For iOS devices, the purchased
software will display in the list, tap it to another application for diagnosis).
5. Plug the connector of the MaxiAP200M Bluetooth dongle into the vehicle's OBDII
port.

5
The vehicle's OBDII port is generally located under the vehicle dashboard
(Consult vehicle user manual for specific location).
6. Turn the vehicle ignition to Key On, Engine Off position.
The LED on the dongle will light solid green when connected.
7. VCI Connection
For Android devices, tap Me > VCI Connection or the VCI button near the top right
of the Home screen.
For iOS devices, tap Setting > Bluetooth on your iOS device to open the Bluetooth
function.
Tap the Bluetooth name on the screen to pair it with the device. The Bluetooth name
starts with AP, followed by the serial number of the dongle.
Ensure your device's Bluetooth is turned on.
When the device is successfully paired with the dongle, the LED will light solid
blue.
NOTE
For iOS devices, once a dongle is paired with device via Bluetooth, it cannot be searched
by other devices. When multiple dongles paired to the same device via Bluetooth, only
the first connected dongle lights blue, others will light green.
8. Your MaxiAP200M is now ready for use.
Figure 2-1 Sample MaxiAP200M Job Menu

6
①Dynamic Rotation Banner –display information about other popular Autel
products, tap the banner to visit the product page on Autel websites,
www.autel.com or www.maxitpms.com.
②Application Buttons.
③Navigation Buttons
Function Buttons
The table below briefly describes each of the applications in theAP200M system.
Table 2-1 Application Buttons
Button
Name
Description
Diagnostics
Accesses vehicle diagnostic functions.
Service
Accesses service functions menu.
History
Accesses diagnosis and service records with vehicle
information and DTCs included.
Repair
Reports
Accesses repair reports for EOBD, diagnostic, and
maintenance sessions.
AP200M_
USA
For iOS devices, this icon will display on the device's
desktop after purchasing and installing the U.S. and
European vehicle diagnostic data package. Tap on
the icon to start the diagnosis.
AP200M_
Asia
For iOS devices, this icon will display on the device's
desktop after purchasing and installing the Asian
vehicle and Audi diagnostic data package. Tap on the
icon to start the diagnosis.
AP200M_
Dms
For iOS devices, this icon will display on the device's
desktop after purchasing and installing the Domestic
and Benz diagnostic data package. Tap on the icon
to start the diagnosis.

7
Navigation Buttons
Operations of the Navigation buttons at the bottom of the screen are described in the
table below:
Table 2-2 Navigation Buttons
Button
Name
Description
Home
Returns to the Home screen.
Mall
Purchase vehicle diagnostic data package.
Me
Displays list of functions, including Order Manager,
Delete Vehicle, Data Logging, VCI Connection, VCI
Manager, Settings and User Manual.
AP200M_
BMW
For iOS devices, this icon will display on the device's
desktop after purchasing and installing the BMW
vehicle diagnostic data package. Tap on the icon to
start the diagnosis.

8
3 EOBD
The OBD II/EOBD diagnosis is available to be downloaded through Mall. This option
presents a quick way to check for DTCs, isolate the cause of an illuminated malfunction
indicator lamp (MIL), check monitor status prior to emissions certification testing, verify
repairs, and perform a number of other services that are emissions-related. The OBD
direct access option is also used for testing OBD II/EOBD compliant vehicles that are not
included in the Diagnostics database.
General Procedure
To access the OBD II/EOBD diagnostics functions
1. Tap the EOBD button. There are two options to establish communication with
the vehicle.
Auto Scan –when this option is selected the diagnostic tool attempts to
establish communication using each protocol in order to determine which
one the vehicle is broadcasting on.
Protocol –when this option is selected the screen opens a submenu of
various protocols. A communication protocol is a standardized way of data
communication between an ECM and a diagnostic tool. Global OBD may
use several different communication protocols.
2. Select a specific protocol under the Protocol option. Wait for the OBD II
Diagnostic Menu to display.
3. Select a function option to continue.
DTC & FFD
I/M Readiness
Live Data
On-Board Monitor
Component Test
Vehicle Information
Vehicle Status
NOTE
Some functions are supported only on certain vehicle makes.
This section describes the various functions of each diagnostic option:

9
DTC & FFD
When this function is selected, the screen displays a list of Stored Codes and Pending
Codes. When the Freeze Frame data of certain DTCs are available for viewing, a
snowflake button will display on the right side of the DTC item.
The erase codes function can be applied by tapping the Clear DTC button at the bottom
of the screen.
Stored Codes
Stored codes are the current emission related DTCs from the ECM of the vehicle.
OBD II/EOBD Codes have a priority according to their emission severity, with higher
priority codes overwriting lower priority codes. The priority of the code determines
the illumination of the MIL and the codes erase procedure. Manufacturers rank
codes differently, so expect to see differences between makes.
Pending Codes
These are codes whose setting conditions were met during the last drive cycle, but
need to be met on two or more consecutive drive cycles before the DTC actually
sets. The intended use of this service is to assist the service technician after a
vehicle repair and after clearing diagnostic information, by reporting test results after
a driving cycle.
a) If a test failed during the driving cycle, the DTC associated with that test is
reported. If the pending fault does not occur again within 40 to 80 warm-up
cycles, the fault is automatically cleared from memory.
b) Test results reported by this service do not necessarily indicate a faulty
component or system. If test results indicate another failure after additional
driving, then a DTC is set to indicate a faulty component or system, and the MIL
is illuminated.
Freeze Frame
In most cases the stored frame is the last DTC that occurred. Certain DTCs, which
have a greater impact on vehicle emission, have a higher priority. In these cases,
the top prioritized DTC is the one for which the freeze frame records are retained.
Freeze frame data includes a “snapshot”of critical parameter values at the time the
DTC is set.
Clear DTC
This option is used to clear all emission related diagnostic data such as, DTCs,
freeze frame data and manufacturer specific enhanced data from the vehicle’s ECM.
A confirmation screen displays when the clear codes option is selected to prevent
accidental loss of data. Select Yes on the confirmation screen to continue or No to
exit.

10
I/M Readiness
This function is used to check the readiness of the monitoring system. It is an excellent
function to use prior to having a vehicle inspected for compliance to a state emissions
program. Selecting I/M Readiness opens a submenu with two choices:
Since DTCs Cleared –displays the status of monitors since the last time the DTCs
are erased.
This Driving Cycle –displays the status of monitors since the beginning of the
current drive cycle.
Live Data
This function displays the real time PID data from ECU. Displayed data includes analog
inputs and outputs, digital inputs and outputs, and system status information broadcast
on the vehicle data stream.
Live data can be displayed in various modes.
On-Board Monitor
This option allows you to view the results of On-Board Monitor tests. The tests are useful
after servicing or after erasing a vehicle's control module memory.
Component Test
This service enables bi-directional control of the ECM so that the diagnostic tool is able
to transmit control commands to operate the vehicle systems. This function is useful in
determining whether the ECM responds to a command well.
Vehicle Information
The option displays the vehicle identification number (VIN), the calibration identification,
and the calibration verification number (CVN), and other information of the test vehicle.
Vehicle Status
This item is used to check the current condition of the vehicle, including communication
protocols of OBD II modules, retrieved codes amount, status of the Malfunction Indicator
Light (MIL), and other additional information.
Exiting Diagnostics
The Diagnostics application remains open as long as there is an active communication
with the vehicle. You must exit the diagnostics operation to stop all communications with
the vehicle before closing the Diagnostics application.

11
NOTE
Damage to the vehicle electronic control module (ECM) may occur if communication is
disrupted. Make sure the wireless connection is properly connected at all times during
testing. Exit all tests before disconnecting the test connection or powering down the tool.

12
4 Diagnostics
The MaxiAP AP200M scans all systems for vehicle diagnosis. The Diagnostics
application can retrieve ECU information, read & erase DTCs, and view live data. This
application accesses the electronic control unit (ECU) for various vehicle control systems,
including engine, transmission, antilock brake system (ABS), airbag system (SRS), etc.
Automatic Selection
The Auto VIN Scan can be selected after selecting the test vehicle manufacturer.
To perform Automatic Selection
1. Tap the Diagnostics application button from the Main Job Menu. The Vehicle
Menu displays.
2. Tap the manufacturer button of the test vehicle.
3. Tap Automatic Selection and the VIN information will be automatically
acquired. Follow the on-screen instruction to display the diagnostic screen.
Manual Selection
When the vehicle's VIN is not automatically retrievable through the vehicle's ECU, or the
specific VIN is unknown, the vehicle can be manually selected.
This mode of vehicle selection is menu driven, repeat the first two steps from the
automatic selection operation and tap Manual Selection. Through a series of on-screen
prompts and selections, the test vehicle is chosen. If needed, press the ESC button at
the bottom right corner of the screen to return to the previous screen.
Navigation
Navigating the Diagnostics interface and selecting test are discussed in this section.
Diagnostics Screen Layout
The diagnostic screen typically includes two sections.

13
Figure 4-1 Sample Diagnostics Menu Screen
1. Diagnostics Toolbar
2. Diagnosis Section
Diagnostics Toolbar
The Diagnostics Toolbar contains a number of buttons such as Home and Data Logging.
The table below provides a brief description of the operations of the Diagnostics Toolbar
buttons.
Table 4-1 Diagnostics Toolbar Buttons
Button
Name
Description
Home
Returns to the AP200M Job Menu.
Data
Logging
Records the test vehicle information and user contact
information.
VCI Icon
Displays the communication status of the VCI.

14
Diagnosis
There are two options available when accessing the Diagnosis section:
1. Auto Scan –starts auto scanning for all the systems on the vehicle.
2. Control Units –displays a selection menu of all available control units of the test
vehicle.
After a section is made and the VCI establishes communication with the vehicle, the
corresponding function menu or selection menu displays.
Auto Scan
The Auto Scan function performs a comprehensive scanning over all the ECUs in the
vehicle to locate systems' faults and retrieve DTCs.
Figure 4-2 Sample Auto Scan Operation Screen
1. Main Section
2. Functional Buttons
Main Section
The Main Section displays the sequence numbers, the scanned systems, and the
diagnostic indicators describing test results.
These indicators are defined as follows:

15
-!-:Indicates that the scanned system may not support the code reading function,
or there is a communication error between the Display Tablet and the control
system.
-?-: Indicates that the vehicle control system has been detected, but the Display
Tablet cannot accurately locate it.
Fault(s) | #: Fault(s) indicates there is/are detected fault code(s) present; “#”
indicates the number of the detected faults.
Pass | No Fault: Indicates the system has passed the scanning process and no
fault has been detected.
To perform further diagnosis or testing on a specific system item, tap the ○ > button to
the right of that item. A Function Menu screen will display.
Functional Buttons
A brief description of the operations of the Auto Scan's Functional Buttons' are displayed
in the table below. Please slide the buttons left and right to see the complete buttons.
Table 4-2 Functional Buttons in Auto Scan
Name
Description
Save
Tap to save vehicle report as PDF.
Report
Displays the diagnostic data in the report form.
Quick Erase
Deletes codes. A warning message screen will display to
inform you of possible data loss when this function is
selected.
OK
Confirms the test result. Continues to the system
diagnosis after the required system is selected by
tapping the item in the Main Section.
Pause
Suspends scanning and it will change to Continue
button after tapping.
ESC
Returns to the previous screen or exits Auto Scan.

16
Control Units
The AP200M device provides accesses to all available systems, which are integrated
into categories such as Powertrain, Body, and Chassis. Manually locate a required
control system for testing through a series of selection choices.
The Function Menu options vary slightly for different vehicles. The function menu may
include:
ECU Information –provides the retrieved ECU information in detail. An information
screen opens upon selection.
Read Codes –displays detailed information of DTC records retrieved from the test
vehicle's ECU.
Erase Codes –erases DTC records and other data from the test vehicle's ECU.
Live Data –retrieves and displays live data and parameters from the test vehicle's
ECU.
ECU Information
This function retrieves and displays the specific information for the tested control unit,
including unit type, version numbers and other specifications.
Read Codes
This function retrieves and displays the DTCs from the vehicle's control system. The
Read Codes screen varies for each vehicle being tested. On some vehicles, freeze frame
data can also be retrieved for viewing.
Erase Codes
After reading the retrieved codes and making appropriate vehicle repairs, use this
function to erase vehicle codes.
Live Data
When this function is selected, the screen displays the data list for the selected module.
The items available for any control module vary from one vehicle to another. The
parameters display in the order that they are transmitted by the ECM, so expect variation
between vehicles.

17
5 Service
The Service section is specially designed to provide you with quick access to the vehicle
systems for various scheduled service and maintenance performances. The typical
service operation screen is a series of menu driven executive commands. By following
the on-screen instructions to select appropriate execution options, enter correct values
or data, and perform necessary actions, the system will guide you through the complete
performance for various service operations.
The service will be listed on the Service section after purchasing. Tap the corresponding
service to select the vehicle makes you need for service operations.
The most commonly performed service functions in AP200M include:
Oil Reset Service
EPB Service
BMS Service
DPF Service
SAS Service
Throttle Match Service
Oil Reset Service
This function allows you to perform reset for the Engine Oil Life system, which calculates
an optimal oil life change interval dependingon the vehicle driving conditions and climate.
The Oil Life Reminder must be reset every time the oil is changed, so the system can
calculate when the next oil change is required.
IMPORTANT
Always reset the engine oil life to 100% after every oil change.
NOTE
All required work must be carried out before the service indicators are reset. Failure to
do so may result in incorrect service values and cause DTCs to be stored by the relevant
control module.
Electronic Parking Brake (EPB) Service
This function has a multitude of usages to maintain the electronic braking system safely
and effectively. The applications include deactivating and activating the brake control

18
system, assisting with brake fluid control, opening and closing brake pads, and setting
brakes after disc or pad replacement, etc.
EPB Safety
It may be dangerous to perform Electronic Parking Brake (EPB) system maintenance, so
before you begin the service work, please keep these rules in mind.
Ensure that you are fully familiar with the braking system and its operation before
commencing any work.
The EPB control system may be required to be deactivated before carrying out any
maintenance/diagnostic work on the brake system. This can be done from the tool
menu.
Only carry out maintenance work when the vehicle is stationary and on level ground.
Ensure that the EPB control system is reactivated after the maintenance work has
been completed.
NOTE
Autel accepts no responsibility for any accident or injury arising from the maintenance of
the Electronic Parking Brake system.
Battery Management System (BMS) Service
The BMS (Battery Management System) allows the scan tool to evaluate the battery
charge state, monitor the close-circuit current, register the battery replacement, and
activate the rest state of the vehicle.
NOTE
1. This function is not supported by all vehicles. The screens shown in this section are
examples.
2. The sub functions and actual test screens of the BMS may vary for different test
vehicles, please follow the on-screen instructions to make correct option selection.
The vehicle may use either a sealed lead-acid battery or an AGM (Absorbed Glass Mat)
battery. Lead acid battery contains liquid sulphuric acid and can spill when overturned.
AGM battery (known as VRLA battery, valve regulated lead acid) also contains sulphuric
acid, but the acid is contained in glass mats between terminal plates.
It is recommended that the replacement aftermarket battery has the same specifications,
such as capacity and type, with the battery used in the vehicle. If the original battery is
replaced with a different type of battery (e.g. a lead-acid battery is replaced with an AGM
battery) or a battery with a different capacity (mAh), the vehicle may require
reprogramming the new battery type in addition to performing the battery reset. Consult
the vehicle manual for additional vehicle-specific information.