Automatic Technology SecuraLift Rhino User manual

SecuraLift® Rhino
AC Overhead Garage Door Opener
INSTALLATION INSTRUCTIONS | OWNER’S COPY

2SecuraLift® Rhino Installation Instructions & Owner’s Manual
WARNING: It is vital for the safety of all persons to
follow these instructions. Failure to comply with the
installation instructions and safety warnings may result
in serious personal injury and/or property damage.
Please save these instructions for future reference.
Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all
conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of
an Automatic Technology Australia Pty Ltd Garage Door Opener. Automatic Technology Australia Pty Ltd hereby further
expressly excludes all or any liability for any injury, damage, cost, expense or claim whatsoever suffered by any person as a
result whether directly or indirectly from failure to install the Automatic Technology Australia Pty Ltd Garage Door Opener
in accordance with these installation instructions.

Installation Instructions & Owner’s Manual SecuraLift® Rhino 3
SecuraLift® Rhino
Overhead Garage Door Opener
Important Safety Instructions 04
Features 06
Operating Controls 08
Package Contents 10
Installation 11
Knockdown C-Rail Assembly 11
C-Rail Assembly 12
Determine Door Type 13
Mounting on a Track Type Door 14
Mounting on a Non-Track Type Door 15
Mounting Door Bracket & Arms 16
Setting Travel Limits 17
Safety Obstruction Force Test 19
Adjusting Safety Obstruction Force 20
Coding Transmitters 21
Door 21
Courtesy Light 21
Vacation Mode 22
Auxiliary Output 22
Pet (Pedestrian) Mode 23
Erasing Transmitter Codes 23
Mounting Wall Transmitter 23
Accessories 24
Terminal Block 24
Remote Aerial 24
P.E. Beams 25
Electric Key Switch 25
Troubleshooting Guide 26
Default Settings & Specifications 27
Parameters 28
Maintenance 30
Parts List 32
Warranty 34

4SecuraLift® Rhino Installation Instructions & Owner’s Manual
Important Safety Instructions
CAUTION: If your garage has no pedestrian entrance door, an emergency access device should be
installed. This accessory allows manual operation of the garage door from outside in the event of
power failure.
For additional protection we strongly recommend fitting of Photo Electric (P.E.) Beams.
In most countries P.E. Beams are mandatory on all automated garage doors. For a small
additional outlay Automatic Technology recommends that P.E. Beams be installed with the SecuraLift®
Rhino Overhead Garage Door Opener.
DO NOT operate the SecuraLift® Rhino Overhead Garage Door Opener unless the garage door
is in full view and free from objects such as cars and children/people. Make sure that the door has
finished moving before entering or leaving the garage.
DO NOT operate the SecuraLift® Rhino Overhead Garage Door Opener when persons are
in or near the doorway. Children near an moving garage door must be supervised at all
times. Serious personal injury and/or property damage can result from failure to follow
this warning.
DO NOT allow children to operate the garage door opener. Serious personal injury
and/or property damage can result from failure to follow this warning.
Regularly check that the safety obstruction force and is tested and set as per
page 19 of this manual. Failure to follow this could result in serious personal
injury and/or property damage. This must be repeated at regular intervals
and adjustments made as required.
DO NOT disengage the SecuraLift® Rhino Overhead Garage Door
Opener to manual operation with persons or any other objects,
including motor vehicles, within the doorway.
The SecuraLift® Rhino Overhead Garage Door Opener is not
intended for use by young children or infirm persons. Children
should be supervised to ensure that they do not play with the
remote transmitters or the opener.
Keep hands and loose clothing clear at all times.
The unit should be installed so that it is protected from
the elements. It should not be exposed to water or
rain, immersed in water or sprayed directly by a
hose or other water carrying device.
WARNING: It is vital for the safety of all persons to follow
all instructions. Failure to comply with the following
safety rules may result in serious personal injury and/or
property damage.

Installation Instructions & Owner’s Manual SecuraLift® Rhino 5
The garage door must be well balanced. Sticking or binding doors must be repaired by a qualified garage door
installer prior to installation of the SecuraLift® Rhino Overhead Garage Door Opener.
Frequently examine the installation, in particular cables, springs and mountings for signs of wear, damage or
imbalance. DO NOT use if repair or adjustment is needed since a fault in the installation or an incorrectly
balanced door may cause injury. DO NOT attempt to repair the door yourself as hardware is under extreme
tension.
Remove or disengage all garage door locks and mechanisms prior to installation of
the opener.
Connect the SecuraLift® Rhino Overhead Garage Door Opener to a properly earthed general
purpose 240V mains power outlet installed by a qualified electrical contractor.
Disconnect the power cord from mains power before making any repairs or removing
covers. Only experienced service personnel should remove covers from the SecuraLift®
Rhino Overhead Garage Door Opener.
When using auto-close mode, a P.E. Beam must be fitted correctly and tested for
operation at regular intervals. Extreme caution is recommended when using auto-
close mode. All safety rules must be followed - see page 24 for full details.
In order for the SecuraLift® Rhino Overhead Garage Door Opener to sense an
object obstructing the doorway, some force must be exerted. As a result the
object, door and/or person may suffer damage or injury.
If the power supply cord is damaged, it must be replaced by an Automatic
Technology service agent.
Make sure that the door is fully open before driving in or out of the
garage and fully closed before leaving the driveway.
Make sure that remote controls are kept out of reach of
children.
Install the wall mounted transmitter in a location where it is
out of reach of children and the garage door is visible.

6SecuraLift® Rhino Installation Instructions & Owner’s Manual
Operation
To open or close the door simply press a button on a TrioCode™ handheld
transmitter, or optional wall switch for two seconds. During open and close cycles
the door can be stopped by pressing the button again. The next actuation will
move the reverse the door’s direction.
Powerful 1/2H.P. (0.370kW) Suspended Motor
Powerful enough for even the largest and heaviest of doors, the SecuraLift®
Rhino Overhead Garage Door Opener has a unique internal motor mounting that
reduces vibration, and ultimately operating noise.
Anti-travel electronic brake
The SecuraLift® Rhino Overhead Garage Door Opener features an anti-travel
electronic brake mechanism to ensure the opener stops the door exactly at the set
limit location. This is of particular importance to large and heavy doors which build
up greater momentum when moving.
TrioCode™ Code Hopping Technology
Every time a TrioCode™ transmitter is used a new security code is randomly generated
from over 4.29 billion possibilities. This greatly enhances the security of the system and
makes “code grabbing” a thing of the past
These transmitters also overcome interference issues by simultaneously sending a signal over three
slightly different frequencies. Even if two of the three signals are jammed, the system will still work.
Microswitch Limits
Allows for fine adjustment of set limits via a user-friendly tactile interface.
ISS (Intelligent Safety obstruction System)
While the door is performing a close cycle, should it hit an obstacle or be restricted in some manner, it
will automatically reverse. The amount of force the door should encounter before reversing is automatically
adjusted during the initial installation of the opener. The door will also stop if restricted whilst opening. The
Safety Obstruction Force should be checked at least once a month. See page 19 for instructions.
Features
Thank you for purchasing the SecuraLift® Rhino
Overhead Garage Door Opener. Designed to suit
sectional, overhead and one piece tilt up doors, the
components and materials used ensure this opener
will provide years of smart, simple and secure
operation. Listed below are just some of the
many world leading features:

Installation Instructions & Owner’s Manual SecuraLift® Rhino 7
Security Code Store
The SecuraLift® Rhino Overhead Garage Door Opener will store up to 14 different transmitters
codes.
Overload Indicator
When the maximum opening and closing force capacity of the SecuraLift® Rhino
Overhead Garage Door Opener is exceeded an audible beeper will sound to indicate
that an overload has occurred.
LED Courtesy Light
The SecuraLift® Rhino Overhead Garage Door Opener’s courtesy light illuminates
automatically whenever the door is activated. The light can also be switched on
and off without operating the door by pressing the button on any transmitter
which has been coded to operate the light. The light will stay on for approximately
three minutes then switch off. These LED lights have a super long life and virtually
never require replacement.
Vacation Mode
A transmitter can be coded to block out all other transmitters that have been
programmed into the opener’s memory. Vacation mode is ideal for homes with
non-permanent tenancy or when the door is to be left idle for extended periods.
Pet (Pedestrian) Mode
A transmitter can be programmed to open the door partially so that the family pet can
enter and exit the garage at any time.
Auto-Close Mode
The opener can be programmed to automatically close after an open cycle. It is compulsory
to install P.E. Beams if this mode is selected, otherwise the door may cause personal injury or
damage to property.
Photo Electric (P.E.) Beams (optional)
The opener has an input for a Photo Electric (P.E.) Beam to be connected for extra protection and use of the
auto-close mode.
Manual Operation
The opener is equipped with a manual disengaging device. If power to the SecuraLift® Rhino Overhead Garage
Door Opener is disrupted for any reason, the door can be put into manual mode by pulling down on the string
handle on an angle towards the door. This will allow you to manually open or close the door. To re-engage pull
the string handle away from the door.

8SecuraLift® Rhino Installation Instructions & Owner’s Manual
P.E. Beams Auto-Close Shunt has to be placed on to enable the Auto-Close feature.
PROG INPUT is used to connect the PG-3 Universal Handheld Programmer to edit control and receiver functions.
Terminal Block:
PWR - Used to power devices such as P.E. Beams and external receiver (100 milliamp max).
PE - Used to connect to P.E. Beams.
PE- - A 0 volt connection for P.E. Beams.
COM - A common -ve ground for accessories.
OSC - Used for the connection of a wired switch (momentary contact). This switch can then be used to open,
stop or close the door. Install the wall switch in a location where the switch is out of reach of children
and the garage door is visible.
AUX - Allows the opener to operate other devices such as external lights, or an alarm system.
OPEN LIMIT LED (Green) is used during installation to set the open limit position. It also illuminates and flashes as
the door opens, and remains on when the open limit position has been reached.
CLOSE LIMIT LED (Red) is used during installation to set the close limit position. It also illuminates and flashes as
the door closes, and remains on when the close limit position has been reached.
MINUS (-) button (Red) is used during installation to set the close limit position. Pressing and holding this button
will move the door in the close direction. Movement stops when the button is released. This button is also used for
storing or erasing the transmitter button you wish to use to command the door to open, stop or close.
NOTE: The safety obstruction system is inoperable whenever the MINUS (-) button is used to move the door.
CODE SET LED (Red) flashes when a transmitter button is stored.
LIMIT SET button (Blue) is used during installation, together with the PLUS (+) and MINUS (-) buttons, to set the
door limit positions. The LIMIT SET button is also used to re-initialise the opener.
SERVICE LED (Yellow) indicates when the opener requires service or repairs.
OPERATE button (Blue) is used during installation to test the open, stop and close cycles for the opener. The
OPERATE button can also be used in lieu of a transmitter to activate the opener.,
FORCE MARGIN SET button. The obstruction force margin is set automatically during installation. The margin
can be adjusted manually using the FORCE MARGIN SET button (White). Holding the FORCE MARGIN SET button
and pressing PLUS (+) or MINUS (-) buttons will increase or decrease the amount of force. The FORCE MARGIN SET
button should only be used if environmental factors, such as high winds, affect the door’s operation.
PLUS (+) button (Green) is used during installation to set the open limit position. Pressing and holding this button
will move the door in the open direction. Movement stops when the button is released.
NOTE: The safety obstruction system is inoperable whenever the PLUS (+) button is used to move the door.
Close Limit Adjust Screw is used during installation to fine tune the close limit position.
Open Limit Adjust Screw is used during installation to fine tune the open limit position.
Operating Controls
01
02
03
04
05
06
07
08
09
10
11
12
14
13

Installation Instructions & Owner’s Manual SecuraLift® Rhino 9
01 02 03
04
05
06
07
08
09
10 11 12
Operating Controls
13 14

10 SecuraLift® Rhino Installation Instructions & Owner’s Manual
Package contents
Drive Unit
1 x SecuraLift®Rhino drive unit (Fig. 01)
1 x Transmitter pack (Fig. 01)
(Pack includes two keyring transmitters and batteries)
1 x Wall mount transmitter with battery
2 x Door attachment arms (Fig. 01)
1 x Accessory and hardware pack (Fig. 01)
1 x Manual Disengagement Cord (Fig. 01)
1 x Installation Manual
Three Piece Knockdown Track With
Pre-Assembled Chain
IMPORTANT NOTE: If a modification to the length of the
track is required, the adjustment must be made from the
drive unit end only.
Single Piece Track With Pre-Assembled
Chain
NOTE: Chain in one piece rail has been tensioned by the
factory. Do not adjust the tension of the chain.
IMPORTANT NOTE: If a modification to the length of the
track is required, the adjustment must be made from the
drive unit end only.
OR
PLUS
01
Fig
02
Fig
03
Fig