Automationdirect.com Productivity 1000 P1-08TRS User manual

1
Sales 800-633-0405 www.productivity1000.com
C1
NO1
C2
NO2
C3
NO3
C4
NO4
C5
NO5
C6
NO6
C7
NO7
C8
NO8
NC5
NC1
P1-08TRS
RELAY
OUTPUT
1000
P1-08TRS Isolated Relay
The P1-08TRS high-current isolated relay
output module provides eight 3A surge-
protected outputs. The P1-08TRS o󰀨ers both
normally open and normally closed relay
contacts for use with the Productivity1000
System.
Output
Specifications . . . . . . . . . . . . . . . . . . . . . . . . .
.1
Module
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . .
.2
QR
Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.2
Wiring
Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.3
Schematic
& Wiring Diagram . . . . . . . . . . . . . . . . . . .
.3
General
Specifications . . . . . . . . . . . . . . . . . . . . . . . .
.4
Te
rminal Block Specifications . . . . . . . . . . . . . . . . . . .
.4
Wa
rning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.4
T
erminal Block sold separately, (see wiring options on page 3).
Wa
rranty: Thirty-day money-back guarantee. Two-year limited
replacement (See www
.productivity1000.com for details).
Output Specifications
Outputs per Module 8
Rated Voltage 6–24 VDC
6–120 VAC
Operating Voltage Range 5.1–30 VDC
5.1–132 VAC
Output Type 6 Relays, FORM A (SPST)
2 Relays, FORM C (SPDT)
AC Frequency 47–63 Hz
Maximum Output Current 3A / point for both AC and DC
2A / point if used with ZIPLink Cable
Minimum Load Current 5mA @ 5VDC
Maximum Inrush Current 3A for 10ms
OFF to ON Response < 10ms
ON to OFF Response < 10ms
Status Indicators Logic Side (8 points)
Commons 8 isolated (1 point / common)
Maximum Applicable Fuse 8A
Typical Relay Life
Voltage & Type of Load Operations at 4A Load Current
30VDC Resistive
30VDC Solenoid
120VAC Resistive
120VAC Solenoid
100,000
100,000
100,000
100,000

2Tech Support 770-844-4200www.productivity1000.com
QR Code
Use any QR Code reader application to
display the module’s product insert.
P1-08TD1
P1-08TD1
12345678910
L
L
L
L
L
L
L
L
24V
1
2
3
4
0V
5
6
7
8
12- 24VDC
+ -
+ -
12345678910
L
L
L
L
L
L
L
L
24V
1
2
3
4
0V
5
6
7
8
12- 24VDC
+ -
DualPower Source
SinglePower Source
3.3- 24VDC
P1-08TD1 Wiring Diagram
Module Installation
WARNING: Do not add or remove modules with
field power applied.
Step One: With latch
in “locked” position, align
connectors on the side of
each module and stack
by pressing together.
Click indicates lock is
engaged.
Step Three: To unstack modules, pull
locking latch up into the unlocked position
and then pull modules apart.
Step Two: Attach field wiring using
the removable terminal block or ZIPLink
wiring system.
WIRE STRIP
LENGTH
MIN
MAX
P1-08TD1
UNLOCK
LOCK
Check all latches are
secure after modules
are connected.

3
Sales 800-633-0405 www.productivity1000.com
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB20
ZL-RTB20-1
ZL-P1-CBL18
ZL-P1-CBL18-1
ZL-P1-CBL18-2
Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P1-CBL18-1P
ZL-P1-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
5Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
ZL-RTB20
ZL-RTB20-1
2
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground
= Complete S
y
ste
m
acommon connec
ti
on p
oi
nt
f
or pow
P1-08TRS Schematic and Wiring Diagram
8 A
User Supplied
External Fuse
Internal Module Circuitry
6–30 VDC
6–120 VAC
50–60 Hz Relay
Drive
Circuit
OUTPUT
COM
NC1
NO1
C2
NO2
C3
NO3
C4
NO4
NC5
C5
NO5
C6
NO6
C7
NO7
C8
NO8
12345678910 11 12 1813 14 15 16 17
L
L
L
L
L
L
L
L
L
6–30 VDC
6–120 VAC
50–60 Hz
C1
L

4Tech Support 770-844-4200www.productivity1000.com
Document Name Edition/Revision Date
P1-08TRS-DS 3rd Edition 9/17/2019
Copyright 2018, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Max.
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Max.
19/64 in (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver 0.1 in (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5 lb·in (0.28 N·m) N/A
WARNING: To minimize the risk of potential safety problems, you should
follow all applicable local and national codes that regulate the installation
and operation of your equipment. These codes vary from area to area and
it is your responsibility to determine which codes should be followed, and
to verify that the equipment, installation, and operation are in compliance
with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from
the failure to follow all applicable codes and standards. We do not
guarantee the products described in this publication are suitable for
your particular application, nor do we assume any responsibility for your
product design, installation, or operation.
If you have any questions concerning the installation or operation of
this equipment, or if you need additional information, please call Technical
Support at 770-844-4200.
This publication is based on information that was available at the time
it was printed. At AutomationDirect.com®we constantly strive to improve
our products and services, so we reserve the right to make changes to
the products and/or publications at any time without notice and without
any obligation. This publication may also discuss features that may not be
available in certain revisions of the product.
*Recommended Screw Driver TW-SD-MSL-1 *See CE Declaration of Conformance for details.
General Specifications
Operating Temperature 0° to 60°C (32° to 140°F)
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Logic Isolation 1800VAC applied for 1 second
Insulation Resistance >10M@ 500 VDC
Heat Dissipation 3000mW
Enclosure Type Open Equipment
Module Location Any I/O position in a Productivity1000 System.
Field Wiring Use ZIPLink Wiring System or removable terminal block
(sold separately). See “Wiring Options” on page 3.
EU Directive
See the “EU Directive” topic in the Productivity Suite
Help File. Information can also be obtained at:
www.productivity1000.com
Connector
(sold separately) 18-Position Removable Terminal Block
Weight 112g (4oz)
Agency Approvals
UL 61010-1 and UL 61010-2-201 File E139594, Canada
& USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-2-201
Safety)*