Automationdirect.com Productivity 2000 P2-SCM User manual

1
Sales 800-633-0405 www.productivity2000.com
2000
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
P2-SCM
Serial Communications
The P2-SCM Serial Communications Module
provides three RS-232 ports and one RS-485
port for Modbus master/slave networking or to
serial devices using ASCII or custom
communication protocols. Port 1 Powers a
C-More Micro when using an RJ-12 connector.
General Specifications ...................... 1
SCM Front Panel........................... 2
Module Installation Procedure................. 2
P2-SCM Configuration Options................ 3
RS-232 Port Specifications ................... 4
RS-485 Port Specifications ................... 4
Port 1 (RS-232) Specifications ................ 5
Port 2 & 3 (RS-232) Specifications ............. 5
Port 4 (RS-485) Specifications ................ 6
Diagnostic LEDs ........................... 7
Warning .................................. 8
Removable Terminal Block Specifications. . . . . . . . 8
Cable Options ............................. 8
Hot Swap Information ....................... 8
General Specifications
Module Type Intelligent
Modules per Base 15 maximum*
I/O Points Used None, mapped directly to tags in CPU
Field Wiring Connector 3 - RJ12, 1 - 4 Position Terminal Block
Operating Temperature 0º to 60ºC (32º to 140ºF)
Storage Temperature -20º to 70ºC (-4º to 158ºF)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC 60068-2-6 (Test Fc)
Shock IEC 60068-2-27 (Test Ea)
Field to Logic Side Isolation None
Insulation Resistance No isolation
Agency Approvals UL508 File E139594, Canada & USA
CE (EN61131-2007)
Module Location Any slot in any base in a Productivity2000 System
Weight 90g (3.2 oz)
Document Name Edition/Revision Date
P2-SCM-DS 1st Ed. 3/6/2015
Copyright 2015, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
*Note: For complete system limits, please refer to the “Hardware and
Communication Limits” table in the Prodctivity Suite Help file, “Automatic Hardware
Configuration” topic (P050).

2Tech Support 770-844-4200www.productivity2000.com
P2-SCM Front Panel
STATUS DISPLAY
- 14 LEDS
- Shows communication
status for each port
PORT 2
- RS-232
PORT 3
- RS-232
PORT 4
- RS-485
PORT 1
- RS-232
- Provides 210mA 5V
power for C-More Micro
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking tab
toward module face. Click indi-
cates lock is
engaged.
WARNING: Explosion hazard – Do not connect or disconnect connectors
or operate switches while circuit is live unless the area is known to be
non-hazardous. Do not hot-swap modules unless the area is known to be
non-hazardous.

3
Sales 800-633-0405 www.productivity2000.com
P2-SCM Configuration Options
Configuration Item Port 1 (RS-232) Ports 2 & 3 (RS-232) Port 4 (RS-485)
Protocol Selections Disabled, Modbus RTU, ASCII/Custom Disabled, Modbus RTU, ASCII/Custom Disabled, Modbus RTU, ASCII/Custom
Data Rate 1200, 2400, 4800, 9600, 19200, 33600, 38400 1200, 2400, 4800, 9600, 19200, 33600, 38400 1200, 2400, 4800, 9600, 19200, 33600, 38400
Parity None, Odd or Even None, Odd or Even None, Odd or Even
Data Bits47 or 8 bits 7 or 8 bits 7 or 8 bits
RTS Off Delay Time1None, or 0-5,000 ms None, or 0-5,000 ms N/A
RTS On Delay Time1None, or 0-5,000 ms None, or 0-5,000 ms N/A
Modbus Character Timeout2None, or 0-10,000 ms None, or 0-10,000 ms None, or 0-10,000 ms
Communication Timeout (Timeout
between query and response) 500-10,500 ms 500-10,500 ms 500-10,500 ms
Response/Request Delay Time N/A N/A None, or 1-5,000 ms
Comm Heartbeat Value22-1,000 sec 2-1,000 sec 2-1,000 sec
Node Address (Station) 1 to 247 1 to 247 1 to 247
CTS N/A Ignore, Wait, System Input3N/A
Enable/Disable CTS Wait Timeout 1-9999 tenths of seconds 1-9999 tenths of seconds N/A
RTS On, Off, Assert During Transmit, System Output On, Off, Assert During Transmit, System Output N/A
RS-485 2-Wire Mode N/A N/A Disable, Enable
Modbus Port Security Read/Write, Read Only Read/Write, Read Only Read/Write, Read Only
1. For “None” selection with Modbus RTU protocol, Modbus.org minimums are used. This minimum is 3.5 character times up to 19, 200 baud rate and
1.75ms over 19,200 baud rate
2. Only applies to Modbus messages
3. CTS signal is only provided on Ports 2 & 3
4. 7-bit data are only supported with Odd or Even parity

4Tech Support 770-844-4200www.productivity2000.com
Port Specifications
RS-232 Ports 1, 2 & 3
Electrical Specifications Min Typ Max Units
Output ON, Space Condition
(3kΩ, 1000pF Load) 5.0 5.2 N/A Volts
Output OFF, Mark Condition
(3kΩ, 1000pF Load)
N/A
-5.2 -5.0 Volts
Output Short-Circuit Current 15 N/A mA
Short-Circuit Duration N/A No Limit Seconds
Output Resistance 300 N/A Ohm
Input ON Threshold N/A 1.6 2.4 Volt
Input OFF Threshold 0.6 1.2 N/A Volt
Input Resistance 3k 5k 7k Ohm
RS-485 Port 4
Electrical Specifications Min Typ Max Units
Driver Differential Output (54Ω Load) 1.5
N/A
N/A Volts
Driver Common-Mode Output
N/A
3 Volts
Driver Short-Circuit Output Current 250 mA
Short-Circuit Duration
(Thermal Shutdown) No Limit Seconds
Receiver Differential Input Threshold 200 N/A mV
Receiver Common-Mode Input -7 12 Volt
Input Resistance 12k
N/A
Ohm
Termination Resistance
(TB Jumper wire ‘T’ to ‘+’) N/A 120 Ohm
Data Rate 1200
N/A
38400 Baud
Data Rate Error N/A ±2 %
Cable Length (38400 baud maximum) 1200 Meter
Line Specifications for RS-485 Port
RS-485 Line Specifications Options Units
Data Rate Setting 1200, 2400, 4800, 9600, 19200, 33600,
38400 Baud
Data Bits Setting17 or 8 Bits
Stop Bits Setting 1 Bits
Parity Setting None1, Odd or Even Parity
Data Transmission Half duplex N/A
1. 7-bit data are only supported with odd or even parity
Line Specifications for RS-232 Ports
RS-232 Line Specifications Options Units
Data Rate Setting 1200, 2400, 4800, 9600, 19200, 33600,
38400 Baud
Data Rate Error ±2 %
Data Bits Setting17 or 8 Bits
Stop Bits Setting 1 Bits
Parity Setting None1, Odd or Even Parity
Data Transmission Half duplex or full duplex N/A
Network Point-to-Point
1. 7-bit data are only supported with odd or even parity

5
Sales 800-633-0405 www.productivity2000.com
Port 1
Port Type RS-232
Description
Non-isolated RS-232 DTE port connects the CPU as a
Modbus/ASCII master or slave to a peripheral device.
Includes ESD and built-in surge protection.
Data Rates Selectable, 1200, 2400, 4800, 9600, 19200, 33600, and
38400
+5V Cable Power Source 210mA maximum at 5V, ±5%. Reverse polarity and overload
protected
TXD RS-232 Transmit output
RX RS-232 Receive input
RTS Handshaking output for modem control
GND Logic ground
Maximum Output Load (TXD/RTS) 3kΩ, 1,000pF
Minimum Output Voltage Swing ±5V
Output Short Circuit Protection ±15mA
Port Status LED Red LED is illuminated when active for TXD, RXD and RTS
Cable Options
EA-MG-PGM-CBL
D2-DSCBL
USB-RS232 with D2-DSCBL
FA-CABKIT
FA-ISOCON for converting RS-232 to isolated RS-485
6-pin RJ12 Female
Modular Connector
6
1
6 GND Logic Ground
5 RTS RS-232 Output
4 TXD RS-232 Output
3 RXD RS-232 Input
2 +5V 210mA Maximum
1 GND Logic Ground
Pin # Signal
6-pin RJ12 Female
Modular Connector
6
1
6 GND Logic Ground
5 RTS RS-232 Output
4 TXD RS-232 Output
3 RXD RS-232 Input
2 CTS RS-232 Input
1 GND Logic Ground
Pin # Signal
Port 2 and 3 (RS-232 Configuration)
Port Type RS-232
Description
Non-isolated RS-232 DTE port connects the CPU as a
Modbus/ASCII master or slave to a peripheral device.
Includes ESD and built-in surge protection.
Data Rates Selectable, 1200, 2400, 4800, 9600, 19200, 33600, and
38400
TXD RS-232 Transmit output
RX RS-232 Receive input
RTS Handshaking output for modem control
GND Logic ground
Maximum Output Load (TXD/RTS) 3kΩ, 1,000pF
Minimum Output Voltage Swing ±5V
Output Short Circuit Protection ±15mA
Port Status LED Red LED is illuminated when active for TXD, RXD and RTS
Cable Options
D2-DSCBL
USB-RS232 with D2-DSCBL
FA-CABKIT
FA-ISOCON for converting RS-232 to isolated RS-485

6Tech Support 770-844-4200www.productivity2000.com
Port 4 (RS-485 Configuration)
Port Type RS-485
Description
Non-isolated RS-485 port connects the CPU as a
Modbus/ASCII master or slave to a peripheral device.
Includes ESD/EFT protection and automatic echo
cancellation when transmitter is active.
Data Rates Selectable, 1200, 2400, 9600, 19200, 33600, 38400
TXD+/RXD+ RS-485 transceiver high
TXD-/RXD- RS-485 transceiver low
GND Logic Ground
Input Impedance 19kΩ
Maximum Load 50 transceivers, 19kΩ each, 60Ω termination
Output Short Circuit
Protection ±250mA, thermal shut-down protection
Electrostatic Discharge
Protection ±8kV per IEC1000-4-2
Electrical Fast Transient
Protection ±2kV per IEC1000-4-4
Minimum Differential
Output Voltage 1.5 V with 60Ω load
Fail Safe Inputs Logic high input state if inputs are unconnected
Maximum Common Mode
Voltage -7.5 V to 12.5 V
Port Status LED RED LED Illuminated when active for TXD and RXD
Cable Options Recommend L19827-XXX from AutomationDirect.com
G
-
+
T
Pin # Signal
G GND
– TXD-/RXD-
+ TXD+/RXD+
T TERMINATION
RS-485

7
Sales 800-633-0405 www.productivity2000.com
Diagnostic LEDs
LED Port 1 Port 2 Port 3 Port 4
RXD X X X X
TXD X X X X
RTS X X X
CTS X X
5V X
1 - All RS232 & RS485 LED’s reflect the actual electrical level of the signal,
there is no direct firmware control of LED’s
2 - RS232 LED’s RXD, TXD, RTS & CTS are turned ON when their voltage on
the RS232 wire is postive (MARK)
a - This occurs when the UART I/O signal is low (GND)
b - They are turned OFF when the voltage on the RS232 wire is
negative (SPACE)
3 - RS485 LED’s RXD & TXD are turned ON when the UART I/O signal is low
(GND)
4 - 5V LED is ON when 5V power is good, 5V LED is OFF when 5V is shorted
to ground

8Tech Support 770-844-4200www.productivity2000.com
WARNING: To minimize the risk of potential safety problems, you should follow all
applicable local and national codes that regulate the installation and operation of
your equipment. These codes vary from area to area and it is your responsibility
to determine which codes should be followed, and to verify that the equipment, in-
stallation, and operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the failure to
follow all applicable codes and standards. We do not guarantee the products
described in this publication are suitable for your particular application, nor do
we assume any responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or operation of this equip-
ment, or if you need additional information, please call Technical Support at
770-844-4200.
This publication is based on information that was available at the time it was
printed. At AutomationDirect.com®we constantly strive to improve our products
and services, so we reserve the right to make changes to the products and/or
publications at any time without notice and without any obligation. This publication
may also discuss features that may not be available in certain revisions of the
product.
Removable Terminal Block Specs (Port 4)
Number of Positions 4 Screw Terminals, 3.5 mm Pitch
Wire Range
16-28 AWG
Solid/Stranded Conductor
“Use Copper Conductors, 75°C or Equivalent”
Screw Driver Size TW-SD-VSL-1 (Recommended)
Screw Torque 0.4 N·m
Cable Options
Recommended L19827-100, Belden #9841 or Equivalent
Important Hot-Swap Information
The Productivity2000 System supports hot-swap!
Individual modules can be taken offline, removed, and
replaced while the rest of the system continues con-
trolling your process. Before attempting to use the hot-
swap feature, be sure to read the hot-swap topic in the
programming software’s help file or our online documen-
tation at AutomationDirect.com for details on how to plan
your installation for use of this powerful feature.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.