Automationdirect.com Productivity 2000 P2-32ND3-1 User manual

Sales 800-633-0405 www.productivity2000.com 1
Input Specifications
Inputs per Module 32 (Sink/Source)
Operating Voltage Range (Tolerance) 12–24 VDC
Input Voltage Range 10.2–26.4 VDC
Peak Voltage Range 30VDC
Input Current 3.5 mA @ 12VDC
7.5 mA @ 24VDC
Maximum Input Current 10mA @ 26.4 VDC
ON Voltage Level >9.5 VDC
OFF Voltage Level <7 VDC
Minimum ON Current 2mA
Maximum OFF Current 1.6 mA
OFF to ON Response 2ms Maximum, 1ms Typical
ON to OFF Response 2ms Maximum, 1ms Typical
Status Indicators Logic Side (32 Points)
Commons per Module 4 Isolated (8 points/common)
D3-1
12–
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
Terminal Block sold separately, (see wiring options on page 3).
Input Specifications .................................................. 1
Module Installation Procedure.................................. 2
QR Code .................................................................. 2
Hot Swap Information............................................... 3
Wiring Options.......................................................... 3
Wiring Diagram and Schematic................................ 3
Warning .................................................................... 4
Connector Specifications.......................................... 4
General Specifications ............................................. 4
P2-32ND3-1 DC Input
The P2-32ND3-1 DC Input Module provides
thirty-two 12–24 VDC sink/source inputs for
use with the Productivity2000 System.

®

www.productivity2000.com Tech Support 770-844-4200
2
Important Hot-Swap Information
The Productivity 2000 supports hot-swap! Individual
modules can be taken offline, removed, and replaced
while the rest of the system continues controlling your
process. Before attempting to use the hot-swap feature,
be sure to read the hot-swap topic in the programming
software’s help file or our online documentation at
AutomationDirect.com for details on how to plan your
installation for use of this powerful feature.
Use any QR Code reader application to
display the module’s product insert.
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for exceptions.
Step One: Align module
catch with base slot and
rotate module into
connector.
Step Two: Pull top locking
tab toward module face. Click
indicates lock is engaged.
Step Three: Attach field
wiring using the removable
terminal block or ZIPLink
wiring
system.
1 Align
with slot
2rotate
to seated
position
Locked Unlocked
QR Code
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

Wiring Diagram and Schematic
Sales 800-633-0405 www.productivity2000.com 3
12–24 VDC
12–24 VDC
12–24 VDC
12–24 VDC
+
+
+
+
INPUT
COM
Internal Module Circuitry
Optical Isolator
12–24 VDC
+
Equivalent Input Circuit
+
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB40
ZL-RTB40-1
ZL-LTB32-24-1
ZL-CBL40
ZL-CBL40-1
ZL-CBL40-2
ZIPLink Pig Tail Cables
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P3-CBL40-1P
ZL-P3-CBL40-2P
3Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground
ZL-RTB-40-1
ZL-RTB40
ZL-LTB32-24-1
TB5 TB6 TB7 TB8
D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 D25 D26 D27 D28 D29 D30 D31 D32
12122121
27
19
91
10
18
27
19
91
10
18
27
19
91
10
18
27
9
18
Note: P2-32ND3 is UL/CUL listed when used with ZL-RTB40
LED Sensor Input
2

www.productivity2000.com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com
4
Document Name Edition/Revision Date
P2-32ND3-1-DS 2nd Edition 9/10/2019
Copyright 2017, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes vary
from area to area and it is your responsibility to determine which
codes should be followed, and to verify that the equipment, instal-
lation, and operation are in compliance with the latest revision of
these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or opera-
tion of this equipment, or if you need additional information, please
call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
General Specifications
Operating Temperature 0° to 60°C (32° to 140°F),
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1500VAC applied for 1 second
Insulation Resistance >10MΩ @ 500VDC
Heat Dissipation 3W
Enclosure Type Open Equipment
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System.
Field Wiring Use ZIPLink Wiring System only. See “Wiring
Options” on page 3.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be obtained
at: www.productivity2000.com
Weight 104g (3.7 oz)
Agency Approvals
UL 61010-1 and UL 61010-2-201 File E139594,
Canada and USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-
2-201 Safety)*
*Meets EMC and Safety requirements. See the D.O.C. for details.
Connector Specifications
Connector Type IDC style Header with latch, Omron XG4A-4034
Number of Pins 40
Pitch 0.1 in (2.54 mm)