Automationdirect.com Productivity 1000 P1-04DAL-2 User manual

1
Sales 800-633-0405 www.productivity1000.com
24V
V2+
V3+
V4+
0V
COM
COM
COM
COM
V1+
P1-04DAL-2
0-10VDC OUT
ANALOG
1000
P1-04DAL-2 Analog Output
The P1-04DAL-2 Low Resolution Voltage Analog
Output Module provides four outputs for converting
digital values from 0–4095 (12-bit) to 0–10 VDC
analog signals for use with the Productivity1000
system.
Output Specifications . . . . . . . . . . . . . . . . . . . . . . . 1
General Specifications . . . . . . . . . . . . . . . . . . . . . . 2
Removable Terminal Block Specifications. . . . . . . . 2
Wiring Diagram and Schematic. . . . . . . . . . . . . . . . 3
Module Installation Procedure. . . . . . . . . . . . . . . . . 4
QR Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Wiring Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Module Configuration . . . . . . . . . . . . . . . . . . . . . . . 5
Linear Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Non-Linear Scaling . . . . . . . . . . . . . . . . . . . . . . . . . 6
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Warranty: Thirty-day money-back guarantee. Two-year limited
replacement (See www.productivity1000.com for details).
Terminal Block sold separately, (see wiring options on page 5).
Output Specifications
Output Channels 4
Module Signal Output Range 0–10 V
Signal Resolution 12-bit
Resolution Value of LSB
(least significant bit) 0–10 V = 2.44 mV / count
1 LSB = 1 count
Data Range 0–4095 counts
Output Type Voltage sourcing at 10mA
Output Value in Fault Mode 0V
Load Impedance ≥1000Ω
Maximum Capacitive Load 0.01 µF
Allowed Load Type Grounded
Maximum Inaccuracy 0.5% of range
Full Scale Calibration Error ±0.2% of range
Offset Calibration Error ±0.2% of range
Accuracy vs. Temperature ±75 PPM / °C maximum full-scale
calibration change (±0.0025% of range / °C)
Max Crosstalk at DC, 50/60Hz -72dB, 1 LSB
Linearity Error (End to End) ±4 LSB max., (±0.1% of full scale)
Monotonic with no missing codes
Output Stability and
Repeatability ±2% LSB after 10 min. warm up (typical)
Output Ripple ±0.2% of full scale
Output Settling Time 0.3 ms max., 5µs min. (full scale range)
All Channel Update Rate 2ms
Maximum Continuous Overload
Outputs current limited to 40mA typical
Continuous overloads on multiple outputs
can damage the module.
Type of Output Protection 0.1 µ Transient Suppressor
Output Signal at Power Up and
Power Down 0V
External Power Supply Required 24VDC (-20% / +25%), 100mA

2Tech Support 770-844-4200www.productivity1000.com
Terminal Block Specifications
Part Number P1-10RTB P1-10RTB-1
Positions 10 Screw Terminals 10 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Max.
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Max.
19/64 in (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver 0.1 in (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5 lb·in (0.28 N·m) N/A
*Recommended Screw Driver TW-SD-MSL-1
General Specifications
Operating Temperature 0º to 60ºC (32º to 140ºF)
Storage Temperature -20º to 70ºC (-4º to 158ºF)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side
Isolation 1800VAC applied for 1 second
Insulation Resistance > 10MΩ@ 500VDC
Heat Dissipation 2000mW
Enclosure Type Open Equipment
Module Location Any I/O position in a Productivity1000 System
Field Wiring Use ZIPLink Wiring System or removable terminal block
(sold separately). See “Wiring Options” on page 5.
EU Directive See the “EU Directive” topic in the Productivity Suite Help
File. Information can also be obtained at:
www.productivity1000.com
Connector Type
(sold separately) 10-position Removable Terminal Block
Weight 62g (2.2 oz)
Agency Approvals UL 61010-2-201 file E139594, Canada & USA
CE (EN61131-2 EMC and EN61010-2-201 Safety)*
*See CE Declaration of Conformance for details.

3
Sales 800-633-0405 www.productivity1000.com
P1-04DAL-2 Schematic
V1+
V2+
V3+
V4+
0V
- +
24VDC User
Supplied
Power
CH1 DAC
CH2 DAC
CH3 DAC
CH4 DAC
CIRCUIT POWER
INTERNAL
MODULE CIRCUITRY
24V
10
1 2 3 4 5 6 7 8 9
ISOLATED ANALOG
ISOLATED ANALOG
CIRCUIT COMMON
voltage source
voltage source
voltage source
voltage source
COM
COM
COM
COM
P1-04DAL-2 Wiring Diagram
Load
Power Supply
0–10
VDC Load
V+
COM
Voltage Output Circuits

4Tech Support 770-844-4200www.productivity1000.com
Module Installation
WARNING: Do not add or remove modules with
field power applied.
Step One: With latch
in “locked” position, align
connectors on the side of
each module and stack
by pressing together.
Click indicates lock is
engaged.
Step Three: To unstack modules, pull
locking latch up into the unlocked position
and then pull modules apart.
Step Two: Attach field wiring using
the removable terminal block or ZIPLink
wiring system.
WIRE STRIP
LENGTH
MIN
MAX
P1-08TD1
UNLOCK
LOCK
Check all latches are
secure after modules
are connected.
QR Code
Use any QR Code reader application to
display the module’s product insert.
P1-08TD1
P1-08TD1
12345678910
L
L
L
L
L
L
L
L
24V
1
2
3
4
0V
5
6
7
8
12- 24VDC
+ -
+ -
12345678910
L
L
L
L
L
L
L
L
24V
1
2
3
4
0V
5
6
7
8
12- 24VDC
+ -
DualPower Source
SinglePower Source
3.3- 24VDC
P1-08TD1 Wiring Diagram

5
Sales 800-633-0405 www.productivity1000.com
Wiring Options
1ZIPLink Connection System
Cable + ZIPLink Module = Complete System
ZIPLink pre-wired
terminal block
cables
0.5 m (1.6 ft)
cable
1.0 m (3.3 ft)
cable
2.0 m (6.6 ft)
cable
ZIPLink Modules
Feed through
ZL-P1-CBL10
ZL-P1-CBL10-1
ZL-P1-CBL10-2
ZL-RTB20
ZL-RTB20-1
2Terminal Block with pigtail cable
1.0 m (3.3 ft)
cable
2.0 m (6.6 ft)
cable
ZL-P1-CBL10-1P
ZL-P1-CBL10-2P
3Screw Terminal Block only
P1-10RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P1-10RTB-1
(Quantity 1)
ZL-RTB20
ZL-RTB20-1
Module Configuration
Using the Hardware Configuration tool in
the Productivity Suite programming software,
drag and drop the P1-04DAL-2 module into the
configuration.
If desired, assign a User Tagname to each
output point channel selected and to each
Status Bit Item.

6Tech Support 770-844-4200www.productivity1000.com
Linear Scaling
4095
0
600
Motor Speed
0
Motor Driver
Select the Input and Output tags appropriate
for the application. Convert raw input signals
to engineering units for use in the program, or
convert engineering units to output signals for
control purposes
max
min
min max
The Scale (Linear) function can be used to:
• Convert an application specific range to range which is native to the
analog output module.
• Make other linear conversions in ranges appropriate to the application.
Non-Linear Scaling
0
.5
1
1.55
2.25
3.07
4
5
7
0
0
0
0
0
0
0
0
1
2
3
4
5
6
6.5
7
0
0
0
0
0
0
0
Level Transmitter Tank Level Display Gauge
7
0
0
0
0
0
0
0
Enter actual output values for each
input value break point.
7
6
5
4
3
2
1
01 2 3 4 5 6 7
The Scale (Non-Linear) function can be used for Non-Linear applications.

7
Sales 800-633-0405 www.productivity1000.com

8Tech Support 770-844-4200www.productivity1000.com
Document Name Edition/Revision Date
P1-04DAL-2-DS 1st Edition 9/7/2017
Copyright 2017, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
WARNING: To minimize the risk of potential safety problems, you should
follow all applicable local and national codes that regulate the installation
and operation of your equipment. These codes vary from area to area and
it is your responsibility to determine which codes should be followed, and
to verify that the equipment, installation, and operation are in compliance
with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from
the failure to follow all applicable codes and standards. We do not
guarantee the products described in this publication are suitable for
your particular application, nor do we assume any responsibility for your
product design, installation, or operation.
If you have any questions concerning the installation or operation of
this equipment, or if you need additional information, please call Technical
Support at 770-844-4200.
This publication is based on information that was available at the time
it was printed. At AutomationDirect.com®we constantly strive to improve
our products and services, so we reserve the right to make changes to
the products and/or publications at any time without notice and without
any obligation. This publication may also discuss features that may not be
available in certain revisions of the product.
8Tech Support 770-844-4200www.productivity1000.com