Automationdirect.com Productivity 2000 P2-08TD1P User manual

2000
Sales 800-633-0405 www.productivity2000.com 1
Document Name Edition/Revision Date
P2-08TD1P-DS 3rd Ed. 2/5/2019
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
Output Specifications ............................................... 1
Module Installation ................................................... 2
Wiring Options.......................................................... 2
Wiring Diagram and Schematic................................ 3
QR Code .................................................................. 3
Hot Swap Information............................................... 3
Warning .................................................................... 4
Removable Terminal Block
Specifications ........................................................... 4
General Specifications ............................................. 4
LED Status ............................................................... 4
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
Terminal Block sold separately, (see wiring options on page 2).
Output Specifications
Outputs per Module 8 sinking
Voltage Rating 12 - 24 VDC
Operating Voltage Range 10.2 - 26.4 VDC
Maximum Output Current 0.25A continuous
On Voltage Drop 0.5VDC
Maximum Inrush Current Self-limited
OFF to ON Response 0.5ms
ON to OFF Response 0.5ms
Overcurrent Trip 0.6A min., 1.2A max. > 50ms duration*
Minimum Load Current to Avoid Open
Load Fault Detection 113µA
Maximum Leakage Current 135µA 10.2–26.4 VDC
Over Temperature Shutdown Independent to each output
Load Resistance to Avoid Open Load
Fault Detection <58kΩ
Status Indicators Logic Side (8 points)
External 24V Error Indicator Logic Side (1 points)
Fault Condition Indicator Logic Side (8 points)
Commons 1
Fuses None
External DC Power Required 24VDC @ 30mA
*Rev B2 and higher.
P2-08TD1P Sinking
Protected DC Output
The P2-08TD1P DC Output Module
provides eight 12-24 VDC sinking
outputs with short-circuit and overload
protection for use with the Productivity2000
System.

www.productivity2000.com Tech Support 770-844-4200
2
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking
tab toward module face. Click
indicates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB20
ZL-RTB20-1
ZL-P2-CBL18
ZL-P2-CBL18-1
ZL-P2-CBL18-2
Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P2-CBL18-1P
ZL-P2-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
5Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
ZL-RTB20
ZL-RTB20-1
2
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground

12345678910 11 12 1813 14 15 16 17
12345678910 11 12 1813 14 15 16 17
L
L
L
L
L
L
L
L
24V
1
2
3
4
5
6
7
8
COM
24V
24V
24V
24V
24V
24V
24V
24V
24VDC
- +
+ -
12-24VDC
L
L
L
L
L
L
L
L
24V
1
2
3
4
5
6
7
8
COM
24V
24V
24V
24V
24V
24V
24V
24V
24VDC + -
SINGLE POWER SOURCE DUAL POWER SOURCE
INTERNALLY CONNECTED INTERNALLY CONNECTED
Sales 800-633-0405 www.productivity2000.com 3
+24VDC
+24V
COMs of both Power Supplies are connected.
12 – 24V
OUTPUT
INTERNAL MODULE
COM
DIGITAL
ISOLATION
NOTE:If two separate power supplies are used to supply module control logic and
output, grounds from both power supplies must be connected. For testing
outputs, see note in P2-USER-M manual under P2-08TD1P wiring.
Sink
L
Important Hot-Swap Information
The Productivity2000 supports hot-swap! Individual
modules can be taken offline, removed, and replaced
while the rest of the system continues controlling your
process. Before attempting to use the hot-swap feature,
be sure to read the hot-swap topic in the programming
software’s help file or our online documentation at
AutomationDirect.com for details on how to plan your
installation for use of this powerful feature.
QR Code
Use any QR Code reader application
to display the module’s product insert.
Wiring Diagram and Schematic
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

www.productivity2000.com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com
4
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes
vary from area to area and it is your responsibility to determine
which codes should be followed, and to verify that the equipment,
installation, and operation are in compliance with the latest revision
of these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or
operation of this equipment, or if you need additional information,
please call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
General Specifications
Operating Temperature 0° to 60°C (32° to 140°F)
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance >10MΩ@ 500VDC
Heat Dissipation 1800mW
Enclosure Type Open Equipment
Agency Approvals UL508 file E139594, Canada & USA
CE (EN61131-2*)
Module Keying to Backplane Electronic
Module Location Any I/O slot in any Productivity2000 System.
Field Wiring
Use ZIPLink Wiring System or removable terminal
block (not included). See “Wiring Options” on
page 2.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be obtained
at: www.productivity2000.com
Connector Type (not included) 18-pin Removable Terminal Block
Weight 97.6g (3.4oz)
*Meets EMC and Safety requirements.
LED Status
Fault Condition Fault Status Indication Operation to Reset Fault
Missing External 24VDC V1 LED is ON Apply external 24 VDC
Open Load (Note 1)
F LED is ON (Note 2)
Connect the load
Over Temperature or
Over Load Current
Turn the output OFF or
cycle power
Note 1: Open Load Fault is always enabled, but is only valid when output is OFF. If Open
Load Fault happens while output is ON, fault will not appear until you turn OFF
output.
Note 2: The SEL button cycles between the output status and fault status. If the “F” LED is
OFF the numbered LEDs are showing output status. If the “F” LED is ON the
numbered LEDs are showing fault status of each output. The “V1” LED is
independent of fault or output display.
Removable Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Number of
Positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30-16 AWG (0.051 - 1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in. (6-7 mm) Strip Length
28-16 AWG (0.081 - 1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
19/64 in. (7-8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.
Screw Driver
Width 0.1 inch (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5 lb·in (0.28 N·m) N/A
*Recommend Screw Driver TW-SD-MSL-1