Automationdirect.com Productivity 2000 P2-16TA User manual


®
www.productivity2000.com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com 1
Document Name Edition/Revision Date
P2-16TA-DS 2nd Ed. 9/10/2019
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
Terminal Block sold separately, (see wiring options on page 3).
P2-16TA AC Output
The P2-16TA AC Output Module provides
sixteen 100-240 VAC outputs for use with the
Productivity2000 system.
Output Specifications ............................................... 1
Module Installation ................................................... 2
QR Code .................................................................. 2
Hot Swap Information............................................... 2
Wiring Options.......................................................... 3
Wiring Diagram and Schematic. ...............................3
Warning .................................................................... 4
Removable Terminal Block Specifications................4
General Specifications ............................................. 4
Output Specifications
Output Channels 16
Rated Voltage 100–240 VAC
Operating Voltage Range 80–288 VAC
Output Type Sourcing
Maximum Output Current 0.5 A / point, 4A / common @ 55°C
0.3 A / point, 2.4 A / common @ 60°C
Minimum Load Current 10 mA
Maximum Leakage Current 4 mA @ 264 VDC
On Voltage Drop 1.5 VAC @ > 50 mA
4.0 VAC @ < 50 mA
Maximum Inrush Current 10A for 10 ms
OFF to ON Response 1 ms + 1/2 cycle
ON to OFF Response 1 ms + 1/2 cycle
AC Frequency 47–63 Hz
Status Indicators Logic Side (16 points)
Commons
2 Isolated Commons for 120V
2 Non-Isolated Commons for 240V
(external jumper required)
Recommended External Fuse 6.3 A Max
(Automation Direct P/N S5006-3-R)

www.productivity2000.com Tech Support 770-844-4200
2
Important Hot-Swap Information
The Productivity2000 supports hot-swap! Individual
modules can be taken offline, removed, and replaced
while the rest of the system continues controlling your
process. Before attempting to use the hot-swap feature,
be sure to read the hot-swap topic in the programming
software’s help file or our online documentation at
AutomationDirect.com for details on how to plan your
installation for use of this powerful feature.
QR Code
Use any QR Code reader application to
display the module’s product insert.
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking
tab toward module face. Click
indicates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

Sales 800-633-0405 www.productivity2000.com 3
Wiring Diagram and Schematic
ZC
6.3A
C1
1
2
3
4
5
6
7
8
C2
9
10
11
12
13
14
15
16
100 - 135 VAC
50 - 60 Hz
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
C1
1
2
3
4
5
6
7
8
C2
9
10
11
12
13
14
15
16
135 - 240 VAC
50 - 60 Hz
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
C1 and C2 Must
Be Linked Externally
for this Voltage Range
12345678910 11 12 1813 14 15 16 17 12345678910 11 12 1813 14 15 16 17
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB20
ZL-RTB20-1
ZL-P2-CBL18
ZL-P2-CBL18-1
ZL-P2-CBL18-2
Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P2-CBL18-1P
ZL-P2-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
5Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
ZL-RTB20
ZL-RTB20-1
2
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground

www.productivity2000.com Tech Support 770-844-4200
4
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes vary
from area to area and it is your responsibility to determine which
codes should be followed, and to verify that the equipment, instal-
lation, and operation are in compliance with the latest revision of
these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or opera-
tion of this equipment, or if you need additional information, please
call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
General Specifications
Operating Temperature 0° to 60°C (32° to 140°F),
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance >10MΩ@ 500VDC
Heat Dissipation 1.9 W
Enclosure Type Open Equipment
Module Keying to Backplane Electronic
Module Location Any I/O slot in any local base in a Productivity2000
System.
Field Wiring
Use ZIPLink Wiring System or removable terminal
block (not included). See “Wiring Options” on page
3.
EU Directive
See the “EU Directive” topic in the Productivity Suite
Help File. Information can also be obtained at:
www.productivity2000.com
Connector Type (not included) 18 position removable terminal block
Weight 90g (3.2oz)
Agency Approvals
UL 61010-1 and UL 61010-2-201 File E139594,
Canada and USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-2-
201 Safety)*
*Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Number of
Positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in. (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
19/64 in. (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.
Screw Driver
Width 0.1 inch (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5∙lbin (0.28 N∙m) N/A
*Recommended Screwdriver TW-SD-MSL-1