Automationdirect.com Productivity 2000 P2-16DA-1 User manual

1
Sales 800-633-0405 www.productivity2000.com
2000
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate the
installation and operation of your equipment. These codes vary from
area to area and it is your responsibility to determine which codes
should be followed, and to verify that the equipment, installation, and
operation are in compliance with the latest revision of these codes.
Equipment damage or serious injury to personnel can result from
the failure to follow all applicable codes and standards. We do not
guarantee the products described in this publication are suitable for
your particular application, nor do we assume any responsibility for
your product design, installation, or operation.
If you have any questions concerning the installation or operation
of this equipment, or if you need additional information, please call
Technical Support at 770-844-4200.
This publication is based on information that was available at the
time it was printed. At AutomationDirect.com®we constantly strive to
improve our products and services, so we reserve the right to make
changes to the products and/or publications at any time without
notice and without any obligation. This publication may also discuss
features that may not be available in certain revisions of the product.
Connector Specifications
Connector Type 24-Pin Molex Style 43025-2400
Number of Pins 24
Pin Spacing 3x3 mm (0.118 x 0.118 in)
1 18.23
2 14.23
3 4.00
4 4.23
5 13.56
6 16.32
7 8.00
8 7.54
M
A
M
A
M
A
M
A
M
A
M
A
M
A
M
A
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
P2-16DA-1 Analog Output
The P2-16DA-1 Current Analog Output Module
provides sixteen channels of 4-20 mA sourcing
outputs for use with the Productivity2000 System.
Warning .................................. 1
Connector Specifications..................... 1
General Specifications ...................... 2
Output Specifications ....................... 2
Wiring Diagram and Schematic................ 3
Module Installation Procedure................. 4
QR Code ................................. 4
Hot Swap Information ....................... 4
Wiring Options............................. 5
Module Configuration ....................... 5
Linear Scaling ............................. 6
Non-Linear Scaling ......................... 6
OLED Panel Display Menus .................. 7

2Tech Support 770-844-4200www.productivity2000.com
General Specifications
Operating Temperature 0º to 60ºC (32º to 140ºF)
Storage Temperature -20º to 70ºC (-4º to 158ºF)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance > 10MΩ @ 500VDC
Heat Dissipation 96mW
Enclosure Type Open Equipment
Agency Approvals UL508 File E139594, Canada & USA
CE (EN61131-2*)
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System
Field Wiring
Use ZIPLink Wiring System ONLY. See “Wiring Options”
on page 5. Must use copper conductors 75ºC or
equivalent.
EU Directive
See the “EU Directive” topic in the Productivity2000
Help File. Information can also be obtained at:
www.productivity2000.com
Connector Type 24-Pin Molex Style 43025-2400
Weight 90g (3.2 oz)
Output Specifications
Output Channels 16
Module Signal Output Range 4-20 mA (Sourcing)
Output Signal Resolution 16-bit
Resolution Value of LSB
(least significant bit)
4-20 mA = 0.244 μA/count
1 LSB = 1 count
Data Range 0 to 65535 counts
Output Type (sourcing) Current: 20mA max
Output Value in Fault Mode Near 0mA
Load Impedance
(Minimum External Power Supply)
0 - 570Ω (19.2 VDC)
0 - 690Ω (21.6 VDC)
0 - 810Ω (24VDC)
0 - 930Ω (26.4 VDC)
0 - 1100Ω (30VDC)
Minimum Load 0Ω @ 0 - 45°C
125Ω @ 45 - 60°C
Maximum Inductive Load 1mH
Allowed Load Type Grounded
Maximum Inaccuracy 0.1% of range
(including temperature drift)
Maximum Full Scale Calibration
Error (not including offset error) ±0.025% of range maximum
Maximum Offset Calibration Error ±0.025% of range maximum
Accuracy vs. Temperature ±25ppm/°C max full scale calibration change
(±0.0025% of range/°C)
Max Crosstalk -96dB, 1 LSB
Linearity Error (End to End) ±16 LSB maximum (±0.025% of full scale)
Monotonic with no missing codes
Output Stability and Repeatability ±10 count after 10 minute warm-up (typical)
Output Ripple 0.05% of full scale
Output Setting Time 300μs max, 5μs min (full scale change)
All Channel Update Rate 3ms
Maximum Continuous Overload Outputs open circuit protected
Type of Output Protection Electronically current limited to 20mA or less
Output Signal (power-up,-down) 4mA
External DC Power Required 24VDC @ 410mA (includes loop power)
*Meets EMC and Safety requirements. See the D.O.C. for details.

3
Sales 800-633-0405 www.productivity2000.com
Current Sourcing Output Circuit
4 - 20mA
Load
Note: Shield is connected to common at the source device.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
ISOLATED ANALOG
CIRCUIT COMMON
ISOLA
TED
ANALOG
CIRCUIT
POWER
CH11 ADC
CH15 ADC
CH12 ADC
CH16 ADC
COM
COM
COM
COM
I1+
I5+
I2+
I6+
I3+
I7+
I4+
I8+
+V
+V
-V
-V
I9+
I13+
I10+
I14+
I11+
I15+
I12+
I16+
INTERNAL
MODULE
CIRCUITRY
CH9 ADC
CH13 ADC
CH10 ADC
CH14 ADC
CH3 ADC
CH7 ADC
CH4 ADC
CH8 ADC
CH1 ADC
CH5 ADC
CH2 ADC
CH6 ADC
+
ZL-RTB20
Labels
Wiring Diagram Schematic

4Tech Support 770-844-4200www.productivity2000.com
Important Hot-Swap Information
The Productivity2000 System supports hot-swap!
Individual modules can be taken offline, removed, and
replaced while the rest of the system continues con-
trolling your process. Before attempting to use the hot-
swap feature, be sure to read the hot-swap topic in the
programming software’s help file or our online documen-
tation at AutomationDirect.com for details on how to plan
your installation for use of this powerful feature.
QR Code
Use any QR Code reader application to
display the module’s product insert.
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
Locked Unlocked
Step One: Align module
catch with base slot and
rotate module into
connector.
Step Two: Pull top locking tab
toward module face. Click indi-
cates lock is
engaged.
Step Three: Attach
field wiring using the
ZIPLink wiring
system.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

5
Sales 800-633-0405 www.productivity2000.com
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-16DA-1 module into the base
configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each output point
(channel) selected and to each Status Bit Item.
A Stop Mode Value may also be assigned.
Module Configuration
Wiring Options
1ZIPLink Connection System
Cable + ZIPLink Module = Complete System
ZIPLink pre-wired
terminal block cables
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZIPLink Modules
Feed through
ZL-P2-CBL24
ZL-P2-CBL24-1
ZL-P2-CBL24-2
ZL-RTB20
2Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P2-CBL24-1P
ZL-P2-CBL24-2P

6Tech Support 770-844-4200www.productivity2000.com
Select the Input and Output tags appropriate
for the application. Convert raw input signals
to engineering units for use in the program, or
convert engineering units to output signals for
control purposes
max
min
min max
Select the minimum and maximum
values of the raw input signal.These
values will relate to the minimum
and maximum scaled values.
7
6
5
4
3
2
1
01 2 3 4 5 6 7
The Scale (Linear) function can be used to:
• Convert an application specific range to a range which is native to the
analog output module.
• Make other linear conversions in ranges appropriate to the application.
The Scale (Non-Linear) function can be used for Non-Linear applications.
Linear Scaling Non-Linear Scaling

7
Sales 800-633-0405 www.productivity2000.com
Momentarily Press
SEL button to
toggle through
secondary displays
Note:
SPARE
denotes
deselected
channel.
Hold SEL button down to cycle through primary screens. Release button to select screen.
Power On
Appears
initially
These screens will
then auto cycle
Error Messages – An existing error will be
inserted into the cycling Status Info screen.
This screen will
auto cycle with
status information
1 0
2 0
3 0
4 0
5 0
6 0
7 0
8 0
9 0
10 0
11 0
12 0
13 0
14 0
15 0
16 0
1 0000H
2 0000H
3 0000H
4 0000H
5 0000H
6 0000H
7 0000H
8 0000H
9 0000H
10 0000H
11 0000H
12 0000H
13 0000H
14 0000H
15 0000H
16 0000H
1 0000H
2 0000H
3 0000H
4 0000H
5 0000H
6 0000H
7 0000H
8 0000H
9 0000H
10 0000H
11 0000H
12 0000H
13 0000H
14 0000H
15 0000H
16 0000H
1 4.00
2 4.00
3 4.00
4 4.00
5 4.00
6 4.00
7 4.00
8 4.00
9 4.00
10 4.00
11 4.00
12 4.00
13 4.00
14 4.00
15 4.00
16 4.00
1 4.00
2 4.00
3 4.00
4 4.00
5 4.00
6 4.00
7 4.00
8 4.00
9 4.00
10 4.00
11 4.00
12 4.00
13 4.00
14 4.00
15 4.00
16 4.00
1 0
2 0
3 0
4 0
5 0
6 0
7 0
8 0
9 0
10 0
11 0
12 0
13 0
14 0
15 0
16 0
MISSING
EXTERNAL
24VDC
MISSING
CONFIG
DATA
End of
Status
Menu
List
SELFTEST
FAIL
REPLACE
MODULE
End of
Status
Menu
List
DISPLAY
UNITS
DECIMAL
COUNTS
DISPLAY
UNITS
HEX
COUNTS
DISPLAY
STATUS
INFO
DISPLAY
SETUP
INFO
DISPLAY
UNITS
MILLIAMP
4-20mA
PASSED
SELF
TEST
P2-16DA1
Fw. Rev.
1.00
16-BIT
4-20mA
OLED Panel Display

8Tech Support 770-844-4200www.productivity2000.com
Document Name Edition/Revision Date
P2-16DA-1-DS 1st Ed. 3/9/2015
Copyright 2015, AutomationDirect.com Incorporated/All Rights Reserved Worldwide