Automationdirect.com Productivity 2000 P2-08TD1S User manual

0S
C1
1
2
3
4
3.3
C2
5
6
7
8
V1
V2
2000
Sales 800-633-0405 www.productivity2000.com 1
Output Specifications ............................................... 1
Module Installation ................................................... 2
Wiring Options.......................................................... 2
Wiring Diagram and Schematic................................ 3
QR Code .................................................................. 3
Hot Swap Information............................................... 3
Warning .................................................................... 4
Removable Terminal Block
Specifications ........................................................... 4
General Specifications ............................................. 4
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
Terminal Block sold separately, (see wiring options on page 2).
P2-08TD1S Sinking DC Output
The P2-08TD1S DC Output Module
provides eight outputs, isolated four per
common, that sink up to 2A per output from
loads powered from 3.3–24 VDC supplies
for use with the Productivity2000 system.
Output Specifications
Outputs per Module 8 sinking
Output Type N-channel MOSFET, open drain
Rated Voltage 3.3–24 VDC
Operating Voltage Range 2.8–30 VDC
Maximum Output Current 2A per point
Minimum Load Current 0.4 mA
Maximum Leakage Current 0.3 mA @ 30VDC
On Voltage Drop 0.2 VDC @ 2A
Maximum Inrush Current 4A for 40ms, 6A for 10ms
OFF to ON Response ≤0.5 ms
ON to OFF Response ≤0.5 ms
Status Indicators Logic Side (8 points)
Commons 2 isolated (4 points / common)
Recommended External Fuse None
External Power Supply Required 12–24 VDC (-15% / +20%) @12mA

www.productivity2000.com Tech Support 770-844-4200
2
Wiring Options
1ZIPLink Connection System
Cable + ZIPLink Module = Complete System
ZIPLink pre-wired
terminal block cables
0.5 m (1.6 FT) cable
1.0 m (3.3 FT) cable
2.0 m (6.6 FT) cable
ZIPLink Modules
Feed through
ZL-P2-CBL18
ZL-P2-CBL18-1
ZL-P2-CBL18-2
ZL-RTB20
ZL-RTB20-1
2Terminal Block with pigtail cable
1.0 m (3.3 FT) cable
2.0 m (6.6 FT) cable
ZL-P2-CBL18-1P
ZL-P2-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
ZL-RTB20
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking
tab toward module face. Click
indicates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
Derating 4A/Common
Max or 1A/Pt

QR CodeWiring Diagram and Schematic
12345678910 11 12 1813 14 15 16 17
L
L
L
L
L
L
L
L
C1
1
2
3
4
V1
C2
5
6
7
8
V2
12 - 24VDC
+ -
12 - 24VDC
+ -
+ -
12345678910 11 12 1813 14 15 16 17
L
L
L
L
L
L
L
L
C1
1
2
3
4
V1
C2
5
6
7
8
V2
12 - 24VDC
+ -
Dual Power
Source
Single Power
Source
Single or Dual Power SourceSingle Power Source
3.3 - 24VDC
Sales 800-633-0405 www.productivity2000.com 3
3.3 - 24V
OUTPUT
INTERNAL MODULE
DIGITAL
ISOLATION
Sink
L
C1/C2
V1/V2 12 - 24VDC
Important Hot-Swap Information
The Productivity2000 supports hot-swap! Individual
modules can be taken offline, removed, and replaced
while the rest of the system continues controlling your
process. Before attempting to use the hot-swap feature,
be sure to read the hot-swap topic in the programming
software’s help file or our online documentation at
AutomationDirect.com for details on how to plan your
installation for use of this powerful feature.
Use any QR Code reader application
to display the module’s product insert.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

www.productivity2000.com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com
4
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes
vary from area to area and it is your responsibility to determine
which codes should be followed, and to verify that the equipment,
installation, and operation are in compliance with the latest revision
of these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or
operation of this equipment, or if you need additional information,
please call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
General Specifications
Operating Temperature 0° to 60°C (32° to 140°F)
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance >10MΩ@ 500 VDC
Heat Dissipation 1800mW
Enclosure Type Open Equipment
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System.
Field Wiring
Use ZIPLink Wiring System or removable terminal
block (not included). See “Wiring Options” on
page 2.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be obtained
at: www.productivity2000.com
Connector Type (sold separately) 18 Position Removable Terminal Block
Weight 98g (3.5 oz)
Agency Approvals UL61010-2-201 file E139594, Canada & USA
CE (EMC: EN61131-2*, Safety EN61010-2-201)
*Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Number of
Positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in. (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
19/64 in. (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.
Screw Driver
Width 1/8 inch (3.8 mm) Maximum
Screw Size M2 N/A
Screw Torque 2.5 lb∙in (0.28 N∙m) N/A
Document Name Edition/Revision Date
P2-08TD1S-DS 1st Ed. Rev. A 10/17/2016
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide