Automationdirect.com Productivity 2000 P2-08TAS User manual


®
P2-08TAS AC
Isolated Output
Sales 800-633-0405 www.productivity2000.com 1
Output Specifications
Outputs per Module 8
Rated Voltage 100–120 VAC
Operating Voltage Range 85–132 VAC
AC Frequency 47–63 Hz
Maximum Output Current 1A / point @ 40°C
0.7 A / point @ 60°C
Minimum Load Current 10mA
Maximum Leakage Current 4mA @ 144VDC
On Voltage Drop 1.5 VAC @ > 50mA
4.0 VAC @ < 50mA
Maximum Inrush Current 3A for 10ms
OFF to ON Response 1ms + 1/2 cycle
ON to OFF Response 1ms + 1/2 cycle
Status Indicators Logic Side (8 points)
Commons 8 Isolated (1 point / common)
Recommended External Fuse 1.6 A Max. (AutomationDirect P/N S5001-6-R)
The P2-08TAS AC Output Module provides
eight 100–120 VAC isolated outputs for use
with the Productivity2000 System.
Output Specifications ..........1
Module Installation Procedure....2
Terminal Block Removal ........2
Hot Swap Information ..........2
Wiring Options................3
Schematic and Wiring Diagram...3
Warning .....................4
Removable Terminal Block
Specifications ................4
General Specifications .........4
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
Terminal Block sold separately (see wiring options on page 3).
P2-08TAS
100-120VAC OUTPUT
C1
1
C2
2
C3
3
C4
4
C5
5
C6
6
C7
7
C8
8

www.productivity2000.com Tech Support 770-844-4200
2
Important Hot-Swap Information
The Productivity2000 supports hot-swap! Individual
modules and entire remote base groups can be taken
offline, removed, and replaced while the rest of the
system continues controlling your process. Before
attempting to use the hot-swap feature, be sure to read
the hot-swap topic in the programming software’s help
file or our online documentation at AutomationDirect.com
for details on how to plan your installation for use of this
powerful feature.
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking
tab toward module face. Click
indicates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
QR Code
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

Schematic and Wiring Diagram
ZC
3.15A
Sales 800-633-0405 www.productivity2000.com 3
N.C.*
C1
1
C2
2
C3
3
C4
4
N.C.*
C5
5
C6
6
C7
7
C8
8
100 - 120 VAC
50 - 60 Hz
L
L
L
L
L
L
L
L
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
*N.C. = No Connection
1.6 A C1
100-120
VAC
50-60Hz
1
ZC
Optical
Isolator
QR Code
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB20
ZL-RTB20-1
ZL-P2-CBL18
ZL-P2-CBL18-1
ZL-P2-CBL18-2
Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P2-CBL18-1P
ZL-P2-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
5Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
ZL-RTB20
ZL-RTB20-1
2
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground

WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes vary
from area to area and it is your responsibility to determine which
codes should be followed, and to verify that the equipment, instal-
lation, and operation are in compliance with the latest revision of
these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or opera-
tion of this equipment, or if you need additional information, please
call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
www.productivity2000 .com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com
4
Document Name Edition/Revision Date
P2-08TAS-DS 2nd Ed. 9/4/2019
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
General Specifications
Operating Air Temperature 0° to 60°C (32° to 140°F),
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance >10MΩ @ 500VDC
Heat Dissipation 1500mW
Enclosure Type Open Equipment
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System.
Field Wiring Use ZIPLink Wiring System or removable terminal
block (not included). See “Wiring Options” on page 3.
EU Directive
See the “EU Directive” topic in the Productivity Suite
Help File. Information can also be obtained at:
www.productivity2000.com
Connector Type (sold separately) 18 position removable terminal block
Weight 85g (2.9 oz)
Agency Approvals
UL 61010-1 and UL 61010-2-201 File E139594,
Canada and USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-2-
201 Safety)*
*Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Number of Positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 sq. mm)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Max.
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Max.
19/64 in (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.
Screw Driver Width 0.1 inch (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5 lb∙in (0.28 N∙m) N/A
*Recommended Screwdriver TW-SD-MSL-1