Automationdirect.com Productivity 2000 P2-15TD2 User manual

12-24VDC SOURCE OUT
V1
V2
COM

®
Sales 800-633-0405 www.productivity2000.com 1
Document Name Edition/Revision Date
P2-15TD2-DS 2nd Ed. 9/5/2019
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide
Output Specifications
Outputs per Module 15 sourcing
Output Type P-channel MOSFET, open source
Rated Voltage 12–24 VDC
Operating Voltage Range 10.2–28.8 VDC
Maximum Output Current 1A per point / 8A per common
Minimum Load Current 1mA
Maximum Leakage Current 0.3 mA @ 28.8 VDC
On Voltage Drop 0.18 VDC @ 1A
Maximum Inrush Current 4A for 40ms, 6A for 10ms
OFF to ON Response ≤0.5 ms
ON to OFF Response ≤0.5 ms
Status Indicators Logic Side (15 points)
Commons 1
Recommended External Fuse None
External Power Supply Required 12–24 VDC (-15% / +20%) @ 22mA
Warranty: Thirty-day money-back guarantee. Two-year limited replacement.
(See www.productivity2000.com for details).
Output Specifications ............................................... 1
Application Notes ..................................................... 1
Module Installation ................................................... 2
Wiring Options.......................................................... 2
Wiring Diagram and Schematic................................ 3
QR Code .................................................................. 3
Hot Swap Information............................................... 3
Warning .................................................................... 4
Removable Terminal Block
Specifications ........................................................... 4
General Specifications ............................................. 4
P2-15TD2 Sourcing
DC Output
The P2-15TD2 DC Output Module
provides fifteen outputs that source up to
1A per output from 12–24 VDC supplies for
use with the Productivity2000 System.
Terminal Block sold separately, (see wiring options on page 2).

www.productivity2000.com Tech Support 770-844-4200
2
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking
tab toward module face. Click
indicates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB20
ZL-RTB20-1
ZL-P2-CBL18
ZL-P2-CBL18-1
ZL-P2-CBL18-2
Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P2-CBL18-1P
ZL-P2-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
5Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
ZL-RTB20
ZL-RTB20-1
2
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground

L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
12 - 24V
V1
1
2
3
4
5
6
7
8
V2
9
10
11
12
13
14
15
COM
+
-
12345678910 11 12 1813 14 15 16 17
12 - 24V
V1,V2 INTERNAL MODULE
COM
DIGITAL
ISOLATION
Source
L
Sales 800-633-0405 www.productivity2000.com 3
QR CodeWiring Diagram and Schematic
Important Hot-Swap Information
The Productivity2000 supports hot-swap! Individual
modules can be taken offline, removed, and replaced
while the rest of the system continues controlling your
process. Before attempting to use the hot-swap feature,
be sure to read the hot-swap topic in the programming
software’s help file or our online documentation at
AutomationDirect.com for details on how to plan your
installation for use of this powerful feature.
Use any QR Code reader application
to display the module’s product insert.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

www.productivity2000.com Tech Support 770-844-4200
4
WARNING: To minimize the risk of potential safety problems, you
should follow all applicable local and national codes that regulate
the installation and operation of your equipment. These codes
vary from area to area and it is your responsibility to determine
which codes should be followed, and to verify that the equipment,
installation, and operation are in compliance with the latest revision
of these codes.
Equipment damage or serious injury to personnel can result
from the failure to follow all applicable codes and standards. We
do not guarantee the products described in this publication are
suitable for your particular application, nor do we assume any
responsibility for your product design, installation, or operation.
If you have any questions concerning the installation or
operation of this equipment, or if you need additional information,
please call Technical Support at 770-844-4200.
This publication is based on information that was available at
the time it was printed. At AutomationDirect.com® we constantly
strive to improve our products and services, so we reserve the right
to make changes to the products and/or publications at any time
without notice and without any obligation. This publication may also
discuss features that may not be available in certain revisions of
the product.
General Specifications
Operating Temperature 0° to 60°C (32° to 140°F),
Storage Temperature -20° to 70°C (-4° to 158°F)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance >10MΩ@ 500VDC
Heat Dissipation 2600mW
Enclosure Type Open Equipment
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System.
Field Wiring
Use ZIPLink Wiring System or removable terminal
block (sold separately). See “Wiring Options” on
page 2.
EU Directive
See the “EU Directive” topic in the Productivity
Suite Help File. Information can also be obtained
at: www.productivity2000.com
Connector Type (sold separately) 18 Position Removable Terminal Block
Weight 100g (3.5 oz)
Agency Approvals
UL 61010-1 and UL 61010-2-201 File E139594,
Canada and USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-
2-201 Safety)*
*Meets EMC and Safety requirements. See the D.O.C. for details.
Removable Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Number of
Positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.
Screw Driver Width 0.1 inch (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5 lb∙in (0.28 N∙m) N/A
*Recommend Screw Driver TW-SD-MSL-1