Avaya Radvision Scopia User manual

TryScopia H.323 and Phone Dialing Guide
H.323 Dialing
It’s important to note that not all devices support all forms of H.323 dialing. You should have received a
meeting invite or email which includes the Meeting ID and PIN (if set by room owner) referenced
hereafter.
There are three dialing formats which can be used to connect to the TryScopia system from an H.323
device:
1. Connecting to the IVR….
For this method, you simply dial one of the regional IP addresses you received in the email invite. Then
when prompted, enter the Meeting ID followed by the # symbol. If prompted for a PIN, enter the PIN
followed by the # symbol.
2. URI and TCS4 Dialing…
You can connect to a TryScopia meeting from a device that supports URI or TCS4 format dialing. Please
refer to the manufacturer and device manual for reference and information about URI dialing support
on your specific device.
If your device supports URI dialing, dial one of the following to connect to a TryScopia meeting;
replacing <MeetingID> with the actual Meeting ID you received:
US <MeetingID>@135.11.84.21 (or <MeetingID>@tryscopia.com)
APAC <MeetingID>@135.10.194.79
EMEA <MeetingID>@198.152.74.80
If your device supports TCS4 dialing, dial one of the following to connect to a TryScopia meeting;
replacing <MeetingID> with the actual Meeting ID you received:
US: 135.11.84.21##<MeetingID> (or tryscopia.com##<MeetingID>)
APAC: 135.10.194.79##<MeetingID>
EMEA: 198.152.74.80##<MeetingID>

3. Register your device to the TryScopia system…
If you choose to or, or if other methods of connecting to a TryScopia meeting are unsuccessful, you can
register your device directly to the TryScopia system. Once registered, you will be able to connect to
calls by simply dialing the Meeting ID. You must have an H.460 capable device to use this method.
To register your device to the TryScopia system, do the following:
a. Enable H.460 in your device settings.
b. Set your device's E.164 to 66xxxx (replacing xxxx with the last four digits of your
telephone number). Some devices refer to the E.164 as “extension”.
c. Enter one of the following IP addresses as the Gatekeeper address in your device.
a. US: 135.11.84.21 (or tryscopia.com)
b. APAC: 135.10.194.79
c. EMEA: 198.152.74.80
d. Once registered simply dial the Meeting ID. If prompted for a PIN, enter the PIN
followed by the # symbol.
Invite an H.323 device to a Meeting…
To invite an H.323 device to a meeting you must have moderator privileges for the meeting.
Once connected to a meeting, do the following to invite an H.323 device.
1. Open the invite dialog from the moderation menu. (Available on Mobile and Desktop)
2. Enter the number of the H.323 device in either IP or URI format in the Address field.
3. After entering the number, press the ‘invite’button.

Phone Dialing
Call Into a Meeting…
To connect to a TryScopia meeting from a phone, simply dial one of the regional numbers below. Then
when prompted, enter the Meeting ID followed by the # symbol. If prompted for a PIN, enter the PIN
followed by the # symbol.
US [phone]
APAC [phone]
EMEA [phone]
Invite a Phone to a Meeting…
To invite a phone to a meeting you must have moderator privileges for the meeting.
Once connected to a meeting, do the following to invite a phone.
1. Open the invite dialog from the moderation menu. (Available on Mobile and Desktop)
2. Enter the + symbol followed by the 11 digit phone number in the Address field.
(For example if you wanted to invite 1-603-666-6230, you would enter
[phone])
3. After entering the number, press the invite button.
***For international calls dial +011 followed by the international number.
TryScopia Support | [email protected]