AXIOMTEK eBOX630A Series User manual

eBOX630A Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, or any liability arising from such uses.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update any information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted in any
forms or by any means, electronic, mechanical, photocopying, recording, among others, without
prior written permissions of Axiomtek Co., Ltd.
©Copyright 2023 Axiomtek Co., Ltd.
All Rights Reserved
May 2023, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety precautions.
1. The eBOX630A does not come with an operating system which must be loaded first before
installation of any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing any internal
components. Use a wrist grounding strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the eBOX630A prior to making any installation. Be sure
both the system and all external devices are turned OFF. Sudden surge of power could
ruin sensitive components. Make sure the eBOX630A is properly grounded.
4. Make sure the voltage of the power source is correct before connecting it to any power
outlet.
5. Turn Off system power before cleaning. Clean the system using a cloth only. Do not spray
any liquid cleaner directly onto the screen.
6. Do not leave equipment in an uncontrolled environment where the storage temperature is
below -40℃or above 80℃as it may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
⚫Before handling a board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. This will help discharge any static electricity on the
human body.
⚫When handling boards and components, wear a wrist grounding strap available from
most electronic component stores.
8. Caution:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST
REMPLACEE
PER UNE BATTERIE DE TYPE INCORRECT.
METTRE AU REBUT LES BATTERIES USAGEES
CONFORMEMENT AUX INSTRUCTIONS
9. Waring:
Hot Surface. Do Not Touch.
Restricted access locations: The equipment should only be installed in a Restricted
Access Area.

iv
Classifications
1. Degree of production against electric shock: not classified
2. Degree of protection against ingress of water: IP40
3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air,
oxygen or nitrous oxide.
4. Mode of operation: Continuous

v
General Cleaning Tips
Please keep the following precautions in mind while understanding the details fully before and
during any cleaning of the computer and any components within.
A piece of dry cloth is ideal to clean the device.
1. Be cautious of any tiny removable components when using a vacuum cleaner to absorb
dirt on the floor.
2. Turn the system off before cleaning up the computer or any components within.
3. Avoid dropping any components inside the computer or getting circuit board damp or wet.
4. For cleaning, be cautious of all kinds of cleaning solvents or chemicals which may cause
allergy to certain individuals.
5. Keep foods, drinks or cigarettes away from the computer.
Cleaning Tools:
Although many companies have created products to help improve the process of cleaning
computer and peripherals, users can also use house hold items accordingly for cleaning. Listed
below are items available for cleaning computer or computer peripherals.
Pay special attention to components requiring designated products for cleaning as
mentioned below.
⚫Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although
paper towels or tissues can be used on most hardware as well, it is recommended to use
a piece of cloth.
⚫Water or rubbing alcohol: A piece of cloth may be somewhat moistened with water or
rubbing alcohol before being rubbed on the computer. Unknown solvents may be harmful
to plastic parts.
⚫Absorb dust, dirt, hair, cigarette and other particles outside of a computer can be one of
the best methods of cleaning a computer. Over time these items may restrict the airflow
in a computer and cause circuitry to corrode.
⚫Cotton swabs: Cotton swabs moistened with rubbing alcohol or water are applicable to
reach areas in a keyboard, mouse and other areas.
⚫Foam swabs: If possible, it is better to use lint free swabs such as foam swabs.
.
【Note】: It is strongly recommended that customer should shut down the system before
starting to clean any single components.
Please follow the steps below:
1.Close all application programs;
2.Close operating software;
3.Turn off power switch;
4.Remove all devices;
5.Pull out power cable.

vi
Scrap Computer Recycling
Please inform the nearest Axiomtek distributor as soon as possible for suitable solutions in case
computers require maintenance or repair; or for recycling in case computers are out of order.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines
Corporation. Intel®and Pentium®are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBasic, Windows 10, Windows 8.1, Windows 8,
Windows 7, Windows XPE, Windows XP, Windows CE embedded, Linux are
trademarks of Microsoft Corporation.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

vii
Table of Contents
Disclaimers.............................................................................................................ii
Safety Precautions................................................................................................ iii
Classifications.......................................................................................................iv
General Cleaning Tips ...........................................................................................v
Scrap Computer Recycling................................................................................... vi
SECTION 1 INTRODUCTION.........................................................................1
1.1 General Descriptions.........................................................................1
1.2 System Specifications....................................................................... 2
1.2.1 CPU ...................................................................................................................2
1.2.2 I/O System ........................................................................................................2
1.2.3 System Specifications.....................................................................................4
1.2.4 Driver CD Contents..........................................................................................5
1.3 Dimensions ........................................................................................6
1.3.1 System Dimensions.........................................................................................6
1.3.2 Wall-mount Bracket Dimensions ...................................................................7
1.3.3 DIN-Rail Bracket Dimensions .........................................................................9
1.4 I/O Outlets......................................................................................... 10
1.5Packing List...................................................................................... 12
1.6Model List......................................................................................... 12
SECTION 2 HARDWARE INSTALLATION .................................................13
2.1Installation of SO-DIMM................................................................... 13
2.2 Installation of Mini PCIe Module (Full-Size).................................... 15
2.3 Installation of NVMe storage (M.2 Key M).......................................17
2.4 Installation of 2.5" SATA Device..................................................... 18
2.5 Installation of SIM Card ...................................................................19
SECTION 3 JUMPER & CONNECTOR SETTINGS.....................................21
3.1 Locations of Jumpers & Connectors............................................. 21
3.2 Summary of Jumper Settings......................................................... 22
3.2.1Restore BIOS Optimal Defaults (JP1)..........................................................22
3.2.2COM1 Data/Power Selection (JP3)...............................................................23
3.2.3COM2 Data/Power Selection (JP4)...............................................................23
3.2.4Auto Power On (SW1)....................................................................................23
3.3 Connectors....................................................................................... 24
3.3.1 DC-in Phoenix Power Connector (CN22).....................................................25
3.3.2 HDMI Connector (CN17,CN18)......................................................................25
3.3.3 DisplayPort++ (CN21)....................................................................................26
3.3.4 RS232/422/485 Serial Port Connector (CN23,CN24)...................................26
3.3.5 Ethernet + USB 3.2 Connector (CN15) ........................................................27
3.3.6 USB 2.0 Connector (USB1 , USB2) ..............................................................28
3.3.7 USB 3.2 Connector (CN19)............................................................................28
3.3.8 Ethernet Port (CN20) .....................................................................................29
3.3.9 8-CH Digital IO (CN2).....................................................................................29
3.3.10 ATX Power on/off (SW3) ...............................................................................30
3.3.11 Reset Button (SW2).......................................................................................30
3.3.12Remote Power Switch Connector (PWRBT1).............................................30
3.3.13AT/ATX Switch...............................................................................................30
3.3.14 Audio Connector (CN3, CN4) .......................................................................31

viii
3.3.15 RS-232 Serial Port Connector (CN16, CN12)...............................................31
3.3.16 SATA Connector (SATA 1 & 2).....................................................................32
3.3.17 SATA Power Connector (CN13,CN14)..........................................................32
3.3.18 SIM Slot (CN9, CN5) .......................................................................................32
3.3.19 Full-Size PCI Express Mini Card Slot (CN8) ................................................33
3.3.20 M.2 2280 Key M (CN6)....................................................................................34
3.3.21 M.2 2230 Key E (CN7).....................................................................................35
SECTION 4 BIOS SETUP UTILITY..............................................................37
4.1 Starting............................................................................................. 37
4.2 Navigation Keys............................................................................... 37
4.3 Main Menu........................................................................................ 38
4.4 Advanced Menu ............................................................................... 39
4.5 Chipset Menu ...................................................................................52
4.6 Boot Menu........................................................................................ 59
4.7Save & Exit Menu............................................................................. 60
APPENDIX A WATCHDOG TIMER .............................................................63
About Watchdog Timer ..................................................................................63
Sample Program.............................................................................................. 64

eBOX630A Series User’s Manual
Introduction 1
SECTION 1
INTRODUCTION
This section contains general information and detailed specifications of the eBOX630A. Section
1 consist of the following sub-sections:
◼General Descriptions
◼System Specifications
◼Dimensions
◼I/O Outlets
◼Packing List
◼Model List
1.1 General Descriptions
The eBOX630A Series features 11th gen Intel®Core™i7/i5/i3 or Celeron®Quad-core
ULT processor (Tiger Lake UP3), high performance yet low power consumption, fan-less
slim type design, -40°C to +60°C extended operating temperature, and 9V to 48V wide range
DC power input with industrial-grade reliability. Highly integrated and with rich IO configuration,
the eBOX630A is perfectly suitable for Edge Computing, Machine vision, Embedded controller,
Robotics applications.
Features
⚫11th gen Intel®Core™i7/i5/i3 or Celeron®Quad-core ULT processor (Tiger Lake UP3)
⚫Dual-channel DDR4-3200 SO-DIMM for up to 64GB of memory
⚫Supports 3x 2.5 GbE, 6 USB, 4 COM
⚫-40°C to +60°C wide operating temperatures
⚫9 to 48 VDC wide range DC power input
⚫Supports triple displays with 2 HDMI, and 1 DisplayPort++
⚫Intel® Iris®Xe integrated graphics (i7 & i5 SKUs)
⚫Trusted platform module (TPM 2.0 onboard)

eBOX630A Series User’s Manual
2 Introduction
Reliable and Stable Design
The embedded system supports 11th gen Intel®Core™i7/i5/i3 or Celeron®Quad-core
ULT processor, along with the features of high performance, industrial-grade operation
temperature/power input and multi-functional design that make it the best solution factory
automation, machine vision, Edge Computing, Robotics applications.
Rich IO Connectivity
The eBOX630A comes with rich I/O interfaces including two RS-232/422/485 ports, two RS-
232, four USB 3.2 ports, two USB 2.0 ports, three 2.5G high speed ethernet, two HDMI 1.4b,
one DisplayPort++,one 8-CH TTL DIO, and one front access SIM slot socket supported.
Embedded O.S. Supported
The eBOX630A with 11th generation platform supports Windows®10 IoT, Windows®11 IoT.
High data security Supported.
The eBOX630A is equipped with two swappable 2.5" SATA storage drive bays that can support
RAID 0/1 for data backup.
1.2 System Specifications
1.2.1 CPU
⚫CPU
◼Intel®Core™i7-1185G7E
◼Intel®Core™i5-1145G7E
◼Intel®Core™i3-1115G4E
◼Intel®Core™Celeron®6305E
⚫Chipset
◼SoC
⚫BIOS
◼American Megatrends Inc. UEFI (Unified Extensible Firmware Interface BIOS.
⚫System Memory
◼2 x 260-pin DDR4-3200 SO-DIMM, up to 64GB
1.2.2 I/O System
⚫Display
◼2 x HDMI 1.4b (3840 x 2160@30 Hz)
◼1 x DisplayPort++ 1.2a

eBOX630A Series User’s Manual
Introduction 3
⚫Ethernet
◼2 x 10/100/1000/2500 Ethernet ports (i226-IT)
◼1 x 10/100/1000/2500 Ethernet ports (i226-LM supports AMT)
⚫USB Ports
◼4 x USB 3.2 Gen 1
◼2 x USB 2.0
⚫Serial Ports
◼2 x RS-232/422/485 (COM1/COM2) (+5V / +12V powered)
◼2 x RS-232 (COM3/COM4) (+5V / +12V powered)
⚫DIO Port
◼1 x 8-CH TTL DIO (DB9 female connector , 4 in & 4 out)
⚫Mini PCIe Interface
◼1 x Full-size PCI Express Mini Card (USB + PCIe signal)
◼1 x M.2 Key E 2230 (for Wi-Fi)
◼1 x M.2 Key M 2280 (for NVMe storage , PCIex4 signal only)
⚫Storage
◼2 x 2.5" swappable SATA HDD/SSD drive bays, up to 9.5mm in height
(Software RAID 0,1)
⚫Indicator
◼1 x Green LED as indicator for PWR status
◼1 x Amber LED as indicator for HDD/SSD active
⚫Switch
◼1 x ATX PWR switch
◼1 x Remote PWR switch
◼1 x AT/ATX Quick switch
◼1 x Reset connector
⚫Antenna & SIM
◼4 x SMA type connector openings for antenna
◼1 x front access SIM slot + 1 internal SIM slot

eBOX630A Series User’s Manual
4 Introduction
⚫TPM 2.0
◼1 x ST33HTPH2X32AHD8
1.2.3 System Specifications
⚫Watchdog Timer
◼1-255 seconds or minutes; up to 255 levels.
⚫Power Supply
◼9V-48V DC input
⚫Operation Temperature
◼-40°C to +60°C (-40°F to +140°F) with 0.5 m/s air flow at 9-48V DC Mode
(with W.T. DRAM & SSD,CPU TDP 15W)
⚫Storage Temperature
◼-40℃to +80℃(-40 ºF to +176ºF)
⚫Humidity
◼10% to 95% (non-condensation)
⚫Shock
◼IEC 60068-2-27 (w/SSD: 50G, half sine,11 ms duration)
⚫Vibration Endurance
◼IEC 60068-2-64 (w/SSD: 3Grms STD, random, 5 - 500 Hz,1 hr/axis)
⚫Weight
◼2.4 kg (5.29 lb) without package
◼3.2 kg (7.0 lb) with package
⚫Dimension
◼250mm (9.84") (W) x 170mm (6.69") (D) x 60mm (2.36") (H)

eBOX630A Series User’s Manual
Introduction 5
1.2.4 Driver CD Contents
Please download the following eBOX630A drivers from the Axiomtek official website.
⚫Ethernet
⚫Chipset
⚫Graphic
⚫Audio
⚫Intel® ME
⚫Intel® Rapid Storage technology
【Note】: All specifications and images are subject to change without notice.

eBOX630A Series User’s Manual
6 Introduction
1.3 Dimensions
The following diagrams show dimensions and outlines of the eBOX630A.
1.3.1 System Dimensions

eBOX630A Series User’s Manual
Introduction 7
1.3.2 Wall-mount Bracket Dimensions
From the accessories box, users can get 4pcs of truss head M3*6L screws for fixing the wall
mount kit.
Note: When users install the wall mount kit, please turn the LAN ports side outlet towards the
floor.

eBOX630A Series User’s Manual
8 Introduction
Wall-mount Bracket Assembly Drawing
From the accessories box, users can get 4pcs of truss head M3*6L screws for fixing the wall
mount kit.
Note : If users install the screws in drywall, use the hollow wall anchors to ensure that the unit
does not pull away from the wall due to prolonged strain between the cable and the
power connector.

eBOX630A Series User’s Manual
Introduction 9
1.3.3 DIN-Rail Bracket Dimensions
From the accessories box, users can get 4pcs of truss head M3*6L and 6pcs of M3*4L
countersunk flat head screws for fixing the DIN-rail mount kit.
DIN-Rail Bracket Assembly Drawing
From the accessory box, users can get 6pcs of truss head M3*6L screws for fixing the
wall mount kit.

eBOX630A Series User’s Manual
10 Introduction
1.4I/O Outlets
The following figures show I/O outlets on the eBOX630A.
Front View
1
2 x Antenna opening
7
1 x Remote power switch
2
2 x Swappable HDD drive bay
8
1 x AT/ATX quick switch
3
2 x Antenna opening
9
2 x USB 2.0
4
LEDs
10
1 x Front access SIM slot
5
1 x Power button
11
1 x Audio (Mic in/Line out)
6
1 x Reset switch
12
1 x 8-CH DIO
(DB9 female,4IN & 4OUT)

eBOX630A Series User’s Manual
Introduction 11
Rear View
13
1 x Grounding screw
19
RS-232/422/485 (COM2)
14
1 x LAN (i226-LM)
20
2 x HDMI 1.4b
15
1 x Antenna opening
21
1 x DisplayPort++
16
RS-232 (COM4)
22
4 x USB 3.2 Gen 1
17
RS-232 (COM3)
23
2 x LAN (i226-IT)
18
RS-232/422/485 (COM1)
24
1 x Phoenix type power
input

eBOX630A Series User’s Manual
12 Introduction
1.5Packing List
The eBOX630A comes with the following bundle package:
⚫eBOX630A system unit x 1
⚫DRAM Thermal Pad x 3
⚫DRAM Bracket x 1
⚫Remote power switch Cable x 1
⚫3-pin Terminal block connector x 1
⚫Foot Pad x 4
⚫Screw pack x 1
⚫M.2 Bracket x 1
⚫M.2 Thermal pad x 3
1.6Model List
eBOX630A-11U-i7
Fanless embedded system with Intel® Core™i7-1185G7E, 2
HDMI, 1 DisplayPort, 3x 2.5GbE LANs, 6 USB, 4 COM, and 9
to 48 VDC
eBOX630A-11U-i5
Fanless embedded system with Intel® Core™i5-1145G7E, 2
HDMI, 1 DisplayPort, 3x 2.5GbE LANs, 6 USB, 4 COM, and 9
to 48 VDC
eBOX630A-11U-i3
Fanless embedded system with Intel® Core™i3-1115G4E, 2
HDMI, 1 DisplayPort, 3x 2.5GbE LANs, 6 USB, 4 COM, and 9
to 48 VDC
eBOX630A-11U-CEL
Fanless embedded system with Intel® Celeron® 6305E, 2
HDMI, 1 DisplayPort, 3x 2.5GbE LANs, 6 USB, 4 COM, and 9
to 48 VDC
Please contact Axiomtek’s distributors immediately in case any abovementioned items are
missing.