AXIOMTEK MPC103-845 User manual

MPC103-845
All-in-One
10.1” WXGA TFT Fanless Touch
Panel Computer with Intel®
Celeron® Processor N3060 onboard
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2018 Axiomtek Co., Ltd.
All Rights Reserved
May 2018, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the MPC103-845 Series before making any installation.
Be sure both the system and the external devices are turned OFF. Sudden surge of
power could ruin sensitive components. Make sure the MPC103-845 Series is properly
grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.2.1 Main CPU Board ......................................................................................... 2
1.2.2 I/O System................................................................................................... 2
1.2.3 System Specifications ................................................................................. 3
1.3 Dimensions..........................................................................................4
1.4 I/O Outlets............................................................................................5
1.5 Packing List.........................................................................................6
Chapter 2 Hardware and Installation ...................... 7
2.1 Jumper and Connector Settings........................................................7
2.1.1 Jumper Settings .......................................................................................... 8
2.1.2 Connector Settings...................................................................................... 9
2.2 Port Definitions..................................................................................15
2.2.1 COM Port .................................................................................................. 15
2.2.2 Ethernet Port............................................................................................. 16
2.3 Mountings –Panel/Wall/Desktop/VESA ..........................................17
2.3.1 Panel-Mounting......................................................................................... 17
2.3.2 VESA-ARM/Wall-Mount ............................................................................ 18
2.4 HDD Installation.................................................................................19
2.4.1 Half-slim SSD Installation.......................................................................... 19
2.5 DRAM Installation..............................................................................21
2.6 Mini Card Installation........................................................................23
2.6.1 Wireless LAN Card Installation ................................................................. 23
2.6.2 mSATA Card Installation............................................................................ 25
2.7 Power Input (Phoenix type)..............................................................26
Chapter 3 AMI BIOS Setup Utility .......................... 27
3.1 Navigation Keys ................................................................................27
3.2 Main Menu..........................................................................................28
3.3 Advanced Menu.................................................................................29
3.3.1 NCT6102D Super IO Configuration .......................................................... 30

v
3.3.2 Hardware Monitor...................................................................................... 32
3.3.3 ACPI Settings............................................................................................ 33
3.3.4 CPU Configuration .................................................................................... 34
3.3.5 SATA Configuration ................................................................................... 35
3.3.6 USB Configuration..................................................................................... 36
3.3.7 Utility Configuration................................................................................... 36
3.3.8 PCIE/mSATA Mini Card Configuration ...................................................... 37
3.4 Chipset Menu.....................................................................................38
3.4.1 North Bridge.............................................................................................. 38
3.4.2 South Bridge.............................................................................................. 39
3.5 Security Menu....................................................................................40
3.6 Boot Menu..........................................................................................41
3.7 Save & Exit Menu ..............................................................................42
Chapter 4 Drivers Installation .............................. 43
4.1 System ...............................................................................................43
4.1.1 Windows 7, 8.X, 10 ................................................................................... 43
4.2 Touch Screen.....................................................................................44
4.2.1 Specification .............................................................................................. 44
4.2.2 Driver Installation- Windows 7/8.X/10....................................................... 44
4.3 Embedded O.S...................................................................................45
4.3.1 WES 7 & WE8S......................................................................................... 45
Appendix A Watchdog Timer & DIO Programming ... 47
About Watchdog Timer................................................................................47
How to Use Watchdog Timer.......................................................................47
WDT Sample Program .................................................................................48
How to Use DIO Software Programming....................................................49
Appendix B Volume Control ...................................... 51
About Volume Control.................................................................................51
How to Use Volume Control........................................................................51
Removed Volume Control Tool...................................................................58

vi
This page is intentionally left blank.

MPC103-845 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the MPC103-845.
Chapter 1 includes the following sections:
General Description
Specifications
Dimensions
I/O Outlets
Package List
1.1 General Description
The MPC103-845 is a fan-less and compact-size medical touch panel computer, equipped with
a 10.1”TFT LCD display and low power consumption Intel® Celeron® Processor N3060 of low
power consumption (with 2M cache, up to 2.48 GHz). It is compatible with Windows 7,
Windows 8.x, Windows 10 and Windows embedded OS. This panel computer can house an
mSATA for storage and two Mini card slots for wireless connection. Its excellent ID and friendly
user interface make it a professional yet easy-to-use panel computer. The MPC103-845 is an
ideal for space-limited in medical application.
MPC103-845: 10.1” TFT XGA Fanless Medical Touch Panel Computer
Reliable and stable design
The MPC103-845 adopts a fanless cooling system which makes it suitable for
environments prone to vibration.
Embedded O.S. supported
The MPC103-845 supports not only Windows 7, Windows 8.x, and Windows 10, but also
embedded O.S. Regarding storage device, the MPC103-845 supports a half slim SSD
and an mSATA.
Industrial-grade product design
The MPC103-845 was adaptively designed to be used in different industrial
environments.
The front bezel meets the IP65 and whole enclosure meets IPX1 standard.
For connecting other devices, the MPC103-845 also features several interfaces: USB,
Ethernet, and RS-232/422/485.

MPC103-845 User’s Manual
2 Introduction
1.2 Specifications
1.2.1 Main CPU Board
CPU
Intel® Celeron® Processor N3060 (2M Cache, up to 2.48 GHz) onboard.
System Memory
One 204-pin DDR3L-1600 SO-DIMM socket
Maximum memory up to 8 BG
BIOS
America Megatrends BIOS
1.2.2 I/O System
Standard I/O
One RS-232/422/485 port
One RS-232 port
Two USB 2.0 ports
Two USB 3.0 ports
Ethernet
Two RJ45 Giga Ethernet ports (Intel i211AT)
Audio
One Line out
Expansion
One Mini-card slot (with SIM slot)
One Mini-card slot (mSATA supported as an option)
Storage
One mSATA
One half slim SSD
Power connector
MPC103-845-J: 12 VDC with external 65W AC adapter and screw type connector;
MPC103-845-DC : 9~36 VDC with phoenix power connector

MPC103-845 User’s Manual
Introduction 3
1.2.3 System Specifications
10.1”WXGA (1280x800) LCD with LED backlight
Project capacitive multi-touch
Fanless heat dispensing design
Disk drive housing:
One half slim SSD(optional only for MPC103-845-J )
mSATA
Net Weight
1.08 kg (2.38 lb)
Dimension (size of main body)
260.8 mm x 194.1 mm x 38 mm
Operation temperature
0℃to 40℃
Relative humidity
10% to 90% @ 40℃, -non-condensing
Vibration
2.0 G, 5 to 500 Hz, random for SSD
Power input
9~36 VDC with phoenix power connector or
External 65W AC adapter
—Power input: 100 to 240 VAC
—Power output: 12 VDC, Max. 5.42 A
NOTE All specifications and images are subject to change without notice.
NOTE The DC power source to be used with MPC103-845 must be galvanically isolated
according to IEC60601-1 safety of medical devices!

MPC103-845 User’s Manual
4 Introduction
1.3 Dimensions
This diagram shows you dimensions and outlines of the MPC103-845.

MPC103-845 User’s Manual
Introduction 5
1.4 I/O Outlets
Please refer to Figures 1-1 and Table 1-1 for I/O locations at the bottom of the MPC103-845.
Figure 1-1 Front view of the MPC103-845
Figure 1-2 Bottom view of the MPC103-845
Table 1-1 Descriptions of I/O Functions at the bottom of the MPC103-845
No
Function
No
Function
1
Power switch (ATX)
7
COM 2 (RS-232)
2
Power Input connector (Screw)
8
Two USB 3.0 ports
3
Power Input connector (Phoenix)
9
Two RJ45 Ethernet
4
Two USB 2.0 ports
10
AT/ATX selectable switch
5
Audio (Line-out)
6
COM 1 (RS-232/422/485)

MPC103-845 User’s Manual
6 Introduction
1.5 Packing List
When you receive the MPC103-845, the bundled package should contain the following items:
MPC103-845 x 1
Driver CD x1
Screws for HDD x4
Phoenix connector x 1 (for MPC103-845-DC)
Power Adapter & power cord (for MPC103-845-J)
If you can’t find the package or any items are missing, please contact Axiomtek distributors
immediately.

MPC103-845 User’s Manual
Hardware and Installation 7
Chapter 2
Hardware and Installation
The MPC103-845 provides rich I/O ports and flexible expansions for users to meet different
demands. The Section is describing hardware installation, including the following subsections:
Jumper and Connector Settings
Port Definitions
Hardware Installation
Mounting Methods
Connecting the Power Input
2.1 Jumper and Connector Settings
Diagram 2-1 Component Side of the Board

MPC103-845 User’s Manual
8 Hardware and Installation
Diagram 2-2 Solder Side of the Board
2.1.1 Jumper Settings
Users can make proper jumper settings to configure the board SBC87845 to suit the needs of
their applications.
Table 2-1 shows the default jumper settings for the MPC103-845.
Table 2-1 Default jumper settings
Jumper
Description
Default Settings
JP1
★OSD function: LCD ON/OFF
OSD function: Touch ON/OFF
Short 1-2
Short 2-3
JP2
★LVDS Panel Power : 3.3V
LVDS Panel Power : 5V
Short 1-2
Short 2-3
JP3
★ATX mode
AT mode
Short 1-2
Short 2-3
JP5
Touch Controller: 4,8 WIRE
★Touch Controller: 5 WIRE
Short 1-2
Short 2-3
JP6
★Normal
Clear CMOS
Short 1-2
Short 2-3
JP7
★Internal Buzzer ENABLE
Internal Buzzer DISABLE
Short 1-2
Short 2-3
JP8
★COM1 normal mode
COM1 pin1 with power :+5V
COM1 pin9 with power :+12V
Short 3-5,4-6
Short 1-3,4-6
Short 3-5,2-4

MPC103-845 User’s Manual
Hardware and Installation 9
NOTE ★ shown above is for default setting.
2.1.2 Connector Settings
The connectors on the CPU Board allow the CPU Board to connect with other parts of the
system. Ensure that all connectors are in place and firmly attached. Table2-2 lists the function
of each connector on the Board SBC87845。
Table 2-2 Connector Settings
Connectors
Description
CN1
LVDS inverter connector
CN2
LVDS connector
CN3
SATA connector
CN4
OSD connector
CN6
HDD power connector
CN7,CN11
Full size min-PCIe connector
CN8
SIM card connector
CN9
DIO connector
CN10
Power connector
CN12
Power Button connector
CN13
Touch connector
CN16
LIN/MIC In connector
CN17
Speaker Out connector
CN18
System Fan connector
CN19
USB2.0 connector
CN20,CN22
RJ45 connector
CN21
USB3.0 connector
CN24
Audio out connector
CN25,CN27
RS232/422/485 Port connector
CN26
RS232 Port connector
CN28,CN29
+5V Standby Power connector
LVDS inverter connector: CN1
Table 2-3 CN1 pin assignment Diagram 2-3 CN1 pin mapping
Pin
Signal
Pin
Signal
1
GND
5
Inverter ON-OFF
2
GND
6
+12V
3
GND
7
+12V
4
Backlight control
8
+12V

MPC103-845 User’s Manual
10 Hardware and Installation
LVDS connector: CN2
Table 2-4 CN2 pin assignment Diagram 2-4 CN2 pin mapping
HDD power connector: CN6
Table 2-5 CN6 Pin Assignment Diagram 2-5 CN6 pin mapping
Pin
Signal
Pin
Signal
1
VCC
21
GND
2
VCC
22
GND
3
VCC
23
LVDSA_DATAN0
4
VCC
24
LVDSB_DATAN2
5
VCC
25
LVDSA_DATAP0
6
VCC
26
LVDSB_DATAP2
7
Resolution selection[0]
27
GND
8
Resolution selection[1]
28
GND
9
GND
29
LVDSA_DATAN1
10
GND
30
LVDSA_DATAN3
11
LVDSB_DATAN3
31
LVDSA_DATAP1
12
LVDSB_DATAN0
32
LVDSA_DATAP3
13
LVDSB_DATAP3
33
GND
14
LVDSB_DATAP0
34
GND
15
GND
35
LVDSA_DATAN2
16
GND
36
LVDSA_CLKN
17
LVDSB_CLKN
37
LVDSA_DATAP2
18
LVDSB_DATAN1
38
LVDSA_CLKP
19
LVDSB_CLKP
39
Resolution selection[2]
20
LVDSB_DATAP1
40
Resolution selection[3]
Pin
Signal
1
+12V
2
GND
3
GND
4
+5V

MPC103-845 User’s Manual
Hardware and Installation 11
Full-size PCI-Express Mini Card: CN7
This is a full-size PCI-Express Mini Card connector on the top side complying with
PCI-Express Mini Card Spec. V1.2. It supports either PCI-Express or USB 2.0.
Pin
Signal
Pin
Signal
1
PCIE_WAKE3_N
2
+3.3V_SBY
3
No use
4
GND
5
No use
6
+1.5V
7
GND
8
SIM_PWR
9
GND
10
SIM_DATA
11
PCIE_REFCLK3_DN
12
SIM_CLK
13
PCIE_REFCLK3_DP
14
SIM_REST
15
GND
16
SIM_VPP
17
No use
18
GND
19
No use
20
+3.3V_SBY
21
GND
22
PLTRST_1_N
23
PCIE_P3_RXN
24
+3.3V_SBY
25
PCIE_P3_RXP
26
GND
27
GND
28
+1.5V
29
GND
30
SMB_CLK_SBY
31
PCIE_P3_TXN
32
SMB_DATA_SBY
33
PCIE_P3_TXP
34
GND
35
GND
36
USB_DN1
37
GND
38
USB_DP1
39
+3.3V_SBY
40
GND
41
+3.3V_SBY
42
No use
43
GND
44
No use
45
No use
46
No use
47
No use
48
+1.5V
49
No use
50
GND
51
No use
52
+3.3V_SBY

MPC103-845 User’s Manual
12 Hardware and Installation
SIM card connector: CN8
Table 2-6 CN8 pin assignment Diagram 2-6 CN8 pin mapping
DIO connector: CN9
Table 2-7 CN9 pin assignment Diagram 2-7 CN9 pin mapping
Pin
Signal
1
GPIO0
2
GPIO1
3
GPIO2
4
GPIO3
5
GPIO4
6
GND
7
GPIO5
8
GPIO6
9
+3.3V
10
GPIO7
Power connector: CN10
Table 2-8 CN10 pin assignment Diagram 2-8 CN10 pin mapping
Pin
Signal
Pin
Signal
1
UIM PWR
5
GND
2
UIM RST
6
UIM VPP
3
UIM CLK
7
UIM DATA
4
NC
8
NC
Pin
Signal
1
DCIN (+12V)
2
DCIN (+12V)
3
GND
4
GND

MPC103-845 User’s Manual
Hardware and Installation 13
Full-size PCI-Express Mini Card and mSATA Connector: CN11
This is a full-size PCI-Express Mini Card connector on the top side complying with
PCI-Express Mini Card Spec. V1.2. It supports either PCI-Express, USB 2.0 or SATA(mSATA).
Power button connector: CN12
Table 2-9 CN12 pin assignment Diagram 2-9 CN12 pin mapping
Pin
Signal
Pin
Signal
1
GND
2
PWBTN
Pin
Signal
Pin
Signal
1
PCIE_WAKE2_N
2
+3.3V_SBY
3
No use
4
GND
5
No use
6
+V1.5S
7
GND
8
No use
9
GND
10
No use
11
PCIE_REFCLK2_DN
12
No use
13
PCIE_REFCLK2_DP
14
No use
15
GND
16
No use
17
No use
18
GND
19
No use
20
+3.3V_SBY
21
GND
22
PLTRST_1_N
23
PCIE_mSATA_Card_RXN
24
+3.3V_SBY
25
PCIE_mSATA_Card_RXP
26
GND
27
GND
28
+V1.5S
29
GND
30
SMB_CLK_3P3_SBY
31
PCIE_mSATA_Card_TXN
32
SMB_DATA_3P3_SBY
33
PCIE_mSATA_Card_TXP
34
GND
35
GND
36
USB_DN2
37
GND
38
USB_DP2
39
+3.3V_SBY
40
GND
41
+3.3V_SBY
42
No use
43
GND
44
No use
45
No use
46
No use
47
No use
48
+V1.5S
49
No use
50
GND
51
No use
52
+3.3V_SBY

MPC103-845 User’s Manual
14 Hardware and Installation
TOUCH connector: CN13
Table 2-11 CN13 pin assignment Diagram 2-10 CN13 pin mapping
Lin/Mic In connector: CN16
Table 2-11 CN16 pin assignment Diagram 2-11 CN16 pin mapping
Pin
Signal
Pin
Signal
1
LIN IN R
2
GND
3
LIN IN L
4
GND
5
MIC IN
6
GND
Speaker connector: CN17
Table 2-12 CN17 pin assignment Diagram 2-12 CN17 pin mapping
Pin
Signal
1
SPKOUT_L-
2
SPKOUT_L+
3
SPKOUT_R-
4
SPKOUT_R+
5
GND
System Fan connector: CN18
Table 2-13 CN18 pin assignment Diagram 2-13 CN18 pin mapping
Pin
Signal
1
GND
2
+12V / Speed control output
3
Fan speed detect
Pin
Signal
1
Sense
2
X+
3
X-
4
Y+
5
Y-