AXIOMTEK PANEL5155-807 User manual

PANEL5155-807
Open Frame 15” TFT Touch
Panel Computer
User’s Manual

ii
Disclaimers
The information in this manual has been carefully checked and is believed to
be accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any
infringements of patents or other rights of third parties, which may result from
its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be
contained in this document. AXIOMTEK makes no commitment to update or
to keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
AXIOMTEK Co., Ltd.
©Copyright 2007 by AXIOMTEK Co., Ltd.
All rights reserved.
March 2007, Version A4
Printed in Taiwan

iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measurers:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.ou

iv
Safety Precautions
Before getting started, read the following important cautions.
1. The PANEL5155-807 does not come equipped with an
operating system. An operating system must be loaded first
before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the PANEL5155-807 before
making any installation. Be sure both the system and the
external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the
PANEL5155-807 is properly grounded.
4. The brightness of the flat panel display decreases with usage.
However, hours of use vary depending on the application
environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The PANEL5155-807 may come with
or w/o a touch screen. Although the touch screen is chemical
resistant, it is recommended that you spray the liquid cleaner
on a cloth first before wiping the screen. In case your system
comes without the touch screen, you must follow the same
procedure and not spray any cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touch screen.
Scratches on the touch screen may cause malfunction or
internal failure to the touch screen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the PANEL5155-807, make sure it is
securely installed.

v
5. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
9Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few seconds.
This will help to discharge any static electricity on your body.
9When handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of
Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties of their
respective owners.

vi
This page does not contain any information.

Table of Contents vii
Table of Contents
Disclaimers........................................................................ii
Safety Approvals................................................................iii
FCC Compliance ..............................................................iii
Safety Precautions .............................................................iv
C h a p t e r 1 .....................................................................1
Introduction..........................................................................1
1.1 General Description ............................................1
1.2 Specifications......................................................1
1.2.1 Main CPU board..................................................1
1.2.2 I/O System ...........................................................2
1.2.3 System Specification ..........................................3
1.3 Dimensions ..........................................................3
1.4 Rear View and I/O Outlets ..................................5
1.4.1 Rear View ............................................................5
1.4.2 I/O Outlet.............................................................6
1.5 Package list..........................................................7
C h a p t e r 2 .....................................................................8
Hardware Installation.........................................................8
2.1 CPU and DRAM Installation ...............................8
2.2 HDD Installation.................................................11
2.3 Serial Port Interface ..........................................12
2.4 VGA.....................................................................12
2.5 Ethernet..............................................................12
2.6 Mountings: VESA/ Wall/ Panel mount.............13
2.6.1 VESA ARM..........................................................13
2.6.2 Wall Mount.........................................................14
2.6.3 Panel-Mount Kit Assembly...............................15
C h a p t e r 3 ...................................................................16
Driver Installation.............................................................16
3.1 System................................................................16

Table of Contents
viii
3.2 P5155-807S Touch Screen ...............................17
3.2.1 Specification .....................................................17
3.2.2 Driver Installation- Windows2000/XP..............18
3.3 P5155-807R Touch Screen...............................21
3.3.1 Specification .....................................................21
3.3.2 Driver Installation- Windows2000/XP..............22
3.3.3 Driver Installation- DOS ....................................24
C h a p t e r 4 ...................................................................28
Embedded O.S. Installation.............................................28
4.1 Windows XP Embedded ...................................28
4.1.1 Calibration Touch Screen for P5155-807S......29
4.1.2 Calibration Touch Screen for P5155-807R......29
4.2 Windows CE.NET 5.0 ........................................30
4.2.1 Calibration Touch Screen for P5155-807S......30
4.2.2 Calibration Touch Screen for P5155-807R......30
A p p e n d i x A ..............................................................31
SBC86807 BIOS Setup.......................................................31
A.1 BIOS Introduction..................................................31
A.2 BIOS Setup.............................................................31
A.2.1 Standard CMOS Setup .....................................33
A.2.2 Advanced BIOS Features.................................36
A.2.3 Advanced Chipset Features ...........................40
A.2.4 Integrated Peripherals .....................................42
A.2.5 Power Management Setup..............................45
A.2.6 PNP/PCI Configuration.....................................48
A.2.7 PC Health Status................................................49
A.2.8 Frequency/Voltage Control............................50
A.2.9 Load Fail-Safe Defaults ....................................51
A.2.10 Load Optimized Defaults .................................52
A.2.11 Set Supervisor/User Password .........................53
A.2.12 Save & Exit Setup ..............................................54
A.2.13 Exit Without Saving ...........................................55
Appendix B.........................................................................56

Table of Contents ix
Power Supply Specification ............................................56
B.1 Power Supply: FSP180-50PLA1 (180W, AC
110~230V Input)...............................................................56
B.1.1 ELECTRICAL REQUIREMENTS ...................................56
B.1.2 EFFICIENCY..............................................................59
B.1.3 ENVIRONMENTAL REQUIREMENTS..........................59
B.1.4 MTBF .........................................................................59
B.1.5 SAFETY......................................................................59
B.2 Power Supply: FSP200-62DL (200W, DC 18~36V
Input)…………………………………………………………60
B.2.1 ELECTRICAL REQUIREMENTS ...................................60
B.2.2 EFFICIENCY..............................................................63
B.2.3 ENVIRONMENTAL REQUIREMENTS..........................63
B.2.4 MTBF .........................................................................63
B.2.5 SAFETY......................................................................63

PANEL5155-807 User’s Manual
Introduction 1
C h a p t e r 1
Introduction
This chapter contains the general information and the detail
specifications of the PANEL5155-807. Chapter 1 includes the
following sections:
General Description
System Specification
Dimensions
Back View & I/O Outlets
Package List
1.1 General Description
The PANEL5155-807 is an Open Frame TFT Touch Panel PC which
equipped with superior Pentium®M/Celeron®M processors and 15"
XGA LCD display. The paradigmatic industrial panel computer,
P5155-807, is a complete full-function and extreme cost-effective
industrial HMI controller.
This ideal industrial-grade panel computer PANEL5155-807 can be
applied to the several of industrial or commercial projects, such as
transportation, factory automation, HMI machine controller, Point Of
Sales, KIOSK and more. Moreover, PANEL5155-807 provides highly
reliable and highly flexible industrial-grade products in all-in-one
solutions.
1.2 Specifications
1.2.1 Main CPU board
CPU: Socket 479 for Intel®Pentium®M and Intel®Celeron®
M Processors.
System Chipset: Intel®852GM+ICH*4
BIOS: Phoenix-Award BIOS, Y2K compliant
4Mbit Flash, DMI, Plug and Play
SmartView for multiple LCD type selection, display
mode option and application extension features

PANEL5155-807 User’s Manual
Introduction
2
RPL/PXE Ethernet Boot ROM
“Load Optimized Default” to backup customized
Setting in the BIOS flash chip to prevent from CMOS
battery fail
System Memory: One 184-pin DDR SDRAM DIMM
Maximum DDR of up to 1GB DDR266
L2 Cache: integrated in CPU
Bus Clock: 400 MHz
Watchdog Timer: Up to 255 levels as Reset feature
1.2.2 I/O System
Standard I/O:
−3 x serial ports with power; 3 x RS-232
−1 x PS/2 for Keyboard Interface
−1 x PS/2 for Mouse Interface
−4 x USB Ports 2.0 compliant
−1 x 15 pin(female) for VGA output
Ethernet:
One Realtek 8100C PCI Bus 10/100M Base-T
One Realtek 8110SC with Giga LAN
Wake On LAN (via ATX power supply)
Equipped with RJ-45 interface
Optional with Realtek RTL8110S for 10/100/1000 Base-T
Audio:
Realtek AC’97 codec audio
MIC-in, Line-out
Onboard IDE:
2 parallel ATA-100 as 1 * 44-pin 2.0 pitch box-header and
1 * 40-pin 2.0 pitch box-header.
PATA-100 as PIO Mode 0-4, DMA Mode 0-2 and Ultra
DMA/33/66/100.
Compact Flash Socket:
One Compact Flash Type II Socket (Optional)

PANEL5155-807 User’s Manual
Introduction 3
1.2.3 System Specification
15” TFT LCD
Disk drive housing:
−1 x internal 3.5” drive
AC power supply
Heat dispensing design
Net weight:
−8.8 Kgs
Dimension (main body size):
−414.5 x 325.3 x 78.9mm
Operating temperature:
−O° to 45°C ; Relative umidity:50%
Relative humidity:
−10% to 85% @ 40° C, non-condensing
Altitude:
−10,000 ft. (3,000 meters)
Vibration (operating):
−5 to 500 Hz, 1 G random
Shock (operating):
−10 G peak acceleration (11 msec. duration)
1.3 Dimensions
The following diagrams show the dimensions and outlines of
PANEL5155-807.

PANEL5155-807 User’s Manual
Introduction 5
1.4 Rear View and I/O Outlets
1.4.1 Rear View
The figure below shows the features and controls on the
PANEL5155-807 Rear chassis.
SEL- SEL+ Backlight ON/OFF

PANEL5155-807 User’s Manual
Introduction
6
1.4.2 I/O Outlet
The following figure shows the I/O locations of the PANEL5155-807.
1: COM 3 6: COM 1 & 2
2: LAN 7: VGA
3: Mic-in, Line-in, Line-Out 8: USB v2.0 * 4
4: Power Switch 9: AC power
5: PS2 x 2 (KB/MS)

PANEL5155-807 User’s Manual
Introduction 7
1.5 Package list
When you receive the PANEL5155-807 there are following items in
the package. If you can not find it, please contact AXIOMTEK
distributors.
1. P5155-807 x 1
2. AC power cord x 1
3. Panel mount kit x 7
4. Wall mount bracket x 1
5. Wall mount screw x 4
6. CD driver x1

PANEL5155-807 User’s Manual
Hardware Installation
8
C h a p t e r 2
Hardware Installation
The PANEL5155-807 provides lots of flexible ways for you to select
different configuration such as CPU, Hard Disk and more. The chapter
will show you how to install the hardware. It includes:
CPU DRAM Hard Disk
Serial Port VGA Ethernet
Mountings
2.1 CPU and DRAM Installation
The standard PANEL5155-807 system is designed Pentium M level
CPUs. The CPU board provides one 184-pin DDR DIMM socket that
supports system memory up to 1GB.
When upgrading the CPU, DRAM, please refer to the following
instructions and illustration:
1. Unscrew screws to remove the rear chassis.
Up side
Left / Right side

PANEL5155-807 User’s Manual
Hardware Installation 9
2. Please be careful of membrane switch and follow below photos
against cable broken.
Rear side

PANEL5155-807 User’s Manual
Hardware Installation
10
3. Install the CPU and DDR DRAM in the PANEL5155-807.
DRAM
CPU

PANEL5155-807 User’s Manual
Hardware Installation 11
2.2 HDD Installation
The PANEL5155-807 offers a convenient drive bay module for users
to install HDD. The PANEL5155-807 offers one 3.5” HDD drive for
users to install. Please follow the steps:
1. Unscrew screws to remove the rear chassis.
2. Unscrew 4 screws from the HDD drive bracket, and take out HDD
bracket kit to install 3.5” HDD.
3. Installation complete.