AXIOMTEK P1197E-861 User manual

P1197E-861
All-in-One
19”SXGA TFT Expandable
PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2015 Axiomtek Co., Ltd.
All Rights Reserved
May 2015, Version A2
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
2. Disconnect the power cords from the P1197 Series before making any installation. Be
sure both the system and the external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the P1197 Series is properly grounded.
3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only
a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Pentium®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
Safety Precautions........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 General Description............................................................................1
1.2 Specifications......................................................................................2
1.3 Dimensions and Outlines ...................................................................4
1.4 I/O Outlets............................................................................................5
1.5 Packing List.........................................................................................5
Chapter 2 Hardware and Installation ...................... 7
2.1 Open back cover .................................................................................8
2.2 Serial Ports Interface ..........................................................................9
2.2.1 COM1&COM2 Connector ........................................................................... 9
2.2.2 COM3 & COM4 Connectors........................................................................ 9
2.2.3 Jumper and Switch Setting ....................................................................... 10
2.3 Ethernet..............................................................................................11
2.4 Mountings: Panel / Wall / Rack / Desktop / VESA...........................12
2.4.1 VESA-ARM / Wall-Mount / Desktop-mount............................................... 12
2.4.2 Panel-mount Kit Assembly ........................................................................ 13
2.4.3 Rack-mount Kit Assembly ......................................................................... 13
2.5 HDD Installation.................................................................................14
2.6 DRAM Installation..............................................................................15
2.7 CPU Installation.................................................................................17
2.8 CPU Cooler Installation ....................................................................19
2.9 Wireless LAN Module Installation (optional)...................................20
2.10 Add-on Card Installation...................................................................22
2.11 Optical Drive Installation (optional).................................................24
Chapter 3 AMI BIOS Setup Utility .......................... 27
3.1 Starting...............................................................................................27
3.2 Navigation Keys ................................................................................27
3.3 Main Menu..........................................................................................28
3.4 Advanced Menu.................................................................................29
3.5 Chipset Menu.....................................................................................40

v
3.6 Boot Menu..........................................................................................48
3.7 Save & Exit Menu ..............................................................................49
Chapter 4 Drivers Installation................................ 51
4.1 System ...............................................................................................51
4.2 Touch Screen.....................................................................................51
4.3 Embedded O.S...................................................................................54
Appendix A Watchdog Timer ..................................... 55
About Watchdog Timer................................................................................55
WatchDog sample code...............................................................................55
Appendix B Digital I/O................................................ 57
Using Digital Output Function ....................................................................57
DIO sample code..........................................................................................57

vi
This page is intentionally left blank.

P1197E-861 User’s Manual
Introduction 1
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the P1197E-861.
Chapter 1 includes the following sections:
General Description
Specification
Dimensions and Outlines
I/O Outlets
Package List
1.1 General Description
The P1197E-861 adopts a 19-inch SXGA TFT LCD with 350-nits brightness and Intel®
3rd&2nd Core™i7/i5/i3 series, Pentium®and Celeron®processors and Intel® H61 chipset to
provide excellent and powerful computing performance. Furthermore, P1197E-861 adopts
built-in speaker and option WLAN module for wireless connectivity.
Industrial-grade front bezel
P1197E-861 adopts industrial-grade material front bezel which incorporates the advantages of
light weight, high degree of hardness better heat releasing, easy-to-shape and anti-corrosion
ability. Therefore, P1197E-861 is especially suitable for most rugged industrial environments.
Expandable for 1 PCIe (1 PCI optional)
P1197E-861 has 1 PCIe (1 PCI optional) for expansion purpose. User can easily plug in
standard half-size PCI or PCIe card for any requirement.
Speaker and WLAN Antenna Supported
P1197E-861 features built-in speakers for kiosk application to display multimedia content
program. It also supports WLAN module (optional) antenna for wireless network connectivity.
Powerful computing: Intel® 3rd Generation Core i7/i5/i3/Celeron processors
P1197E-861 features Intel®3rd&2nd Core™ i7/i5/i3 series, Pentium®and Celeron®processors
and Intel®H61 chipset which deliver high computing performance capability. Ivy Bridge CPU
offers reliable and stable performance and rugged environment.

P1197E-861 User’s Manual
2 Introduction
1.2 Specifications
Main CPU Board
CPU
Intel®3rd&2nd Core™i7/i5/i3 series, Pentium®and Celeron®processors
System Chipset
Intel®H61 Express Chipset
System Memory
2 x 204-pin DDR3 SO-DIMM socket
Supporting 8GB per DIMM, maximum memory size up to 16GB
BIOS
America Megatrends BIOS (AMI UEFI BIOS)
I/O System
Standard I/O
1 x RS-232/422/485 (COM1), 1 x RS-232 with 5V/12V(COM3), 3 x RS-232(COM4)
2 x USB 2.0 (front)
6 x USB 2.0 (back)
1 x DVI-D
1 x VGA
Ethernet
2 x RJ45 for Giga Ethernet
Audio
1 x Line-out
1 x Mic-in
Expansion
1 x Wireless Module(optional)
1 x PCIe x 4 slots Riser card (1 x PCI slots Riser card optional)
Storage
2 x 2.5” SATA HDD
Power connector
1 x AC plug

P1197E-861 User’s Manual
Introduction 3
System Specification
19”SXGA(1280 X 1024)LCD
5 wired resistive Touch
IP65/NEMA4 aluminum front bezel
IP65 aluminum front bezel
Net Weight
8Kgs (17.64 lb)
Dimension (Main Body Size)
482 x 94.7 x 380mm
Operation Temperature
0℃to 45℃
Relative Humidity
10% to 95% @ 40℃, Non-Condensing
Power Input
100~240VAC power connector
NOTE: 1. All specifications and images are subject to change without notice.
2. The speed of expansion card will depend on your CPU.
3. On-Screen Display Combo keys: Pressing VOL+ & VOL- means Audio mute.

P1197E-861 User’s Manual
4 Introduction
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of P1197E-861.

P1197E-861 User’s Manual
Introduction 5
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the P1197E-861.
1.5 Packing List
When you receive the P1197E-861, the bundled package should contain the following items:
P1197E-861 unit x 1
Driver CD x1
Panel mount kit x 9
Wall/VESA mount kit x 1 (optional)
Power cord x 1
If you can not find the package or any items are missing, please contact Axiomtek distributors
immediately.

P1197E-861 User’s Manual
6 Introduction
This page is intentionally left blank.

P1197E-861 User’s Manual
Hardware and Installation 7
Chapter 2
Hardware and Installation
The P1197E-861 provides rich I/O ports and flexible expansions for you to meet different
demand. The chapter will show you how to install the hardware. It includes:
Open back cover
Serial Port Interface
Ethernet
Mounting Method
Hard disk
DRAM
CPU
CPU Cooler
Wireless LAN Module(optional)
Add-on Card
Optical Drive

P1197E-861 User’s Manual
8 Hardware and Installation
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 3 screws on the back cover and push to the right side. Please refer
the photo below.
Step 2 Remove the back cover and unscrew 2 screws.

P1197E-861 User’s Manual
Hardware and Installation 9
2.2 Serial Ports Interface
The P1197E-861 has four serial ports. COM1 is RS-232/422/485, while COM2, COM3 and
COM4 are RS-232.
2.2.1 COM1&COM2 Connector
The COM1&COM2 are double-deck DB-9 connectors. The upper connector is for COM1
and the lower connector is for COM2.
COM1
COM2
2.2.2 COM3 & COM4 Connectors
The COM3 and COM4 interfaces are available through COM34 and COM56,
respectively.
COM34, COM56
Pin
Pin
Signal
1
10
Data Carrier Detect (DCD)
2
11
Receive Data (RXD)
3
12
Transmit Data (TXD)
4
13
Data Terminal Ready (DTR)
5
14
Ground (GND)
6
15
Data Set Ready (DSR)
7
16
Request to Send (RTS)
8
17
Clear to Send (CTS)
9
18
Ring Indicator (RI)
Pin
Signal
Pin
Signal
1
DCD#
2
DSR#
3
RXD
4
RTS#
5
TXD
6
CTS#
7
DTR#
8
RI#
9
GND
10
GND
11
DCD#
12
DSR#
13
RXD
14
RTS#
15
TXD
16
CTS#
17
DTR#
18
RI#
19
GND
20
GND

P1197E-861 User’s Manual
10 Hardware and Installation
2.2.3 Jumper and Switch Setting
Jumpers and Connectors Layout
Jumper Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins
to open. The following illustration shows how to set up jumper.
Select COM for RS-232/422/485
SelectCOM
Pin
Signal
Pin
Signal
1
UART1_RXD
2
COM1_485_RXD
3
UART1_RXD
4
COM1_422_RXD
5
UART1_RXD
6
COM1_232_RXD
7
COM1_BUF_DCD#
8
COM1_BUF_TXD
9
COM1_DCD#
10
COM1_TXD
11
COM1_TXD422-
12
COM1_RXD422+
13
COM1_BUF_RXD
14
COM1_BUF_
DTR#
15
COM1_RXD
16
COM1_DTR#
17
COM1_ TXD422+
18
COM1_RXD422-

P1197E-861 User’s Manual
Hardware and Installation 11
2.3 Ethernet
The P1197E-861 is equipped with two high performance plug and play Ethernet interfaces
(RJ-45). Connection can be established by plugging one end of the Ethernet cable into this
RJ-45 connector and the other end to a 1000/100/10-Base-T hub.
Each of these ports allows Gigabit connection to a Local Area Network (LAN) through a
network hub. Refer to the table below for the LAN port LED indications.
SPEED LED
ACT / LINK LED
Status
Description
Status
Description
OFF
10Mbps connection
OFF
No link
Orange
100Mbps connection
Green
Link
Green
1Gbps connection
Blinking
Data activity

P1197E-861 User’s Manual
12 Hardware and Installation
2.4 Mountings: Panel / Wall / Rack / Desktop / VESA
There are 5 application options for the P1197E-861, including Panel/Wall/Rack/ Desktop/VESA
mounting ways.
2.4.1 VESA-ARM / Wall-Mount / Desktop-mount
The P1197E-861 provides VESA mount: 75x75 mm or 100x100mm. Screw six screws to
fix the kit in the back chassis.
▲VESA/ Wall mount bracket
▲Putting the bracket on the back of system
▲Fixing the bracket by four screws on the left and right side.

P1197E-861 User’s Manual
Hardware and Installation 13
2.4.2 Panel-mount Kit Assembly
The P1197E-861 is designed for panel mount application. To mount the P1197E-861, the
standard set of mounting kit (included in the system packaging) is needed.
2.4.3 Rack-mount Kit Assembly
The P1197E-861 is designed for rack mount application.
Step 1 Remove 8 seal pads in front panel.
Step 2 P1197E-861 could mount directly to standard 19” industrial rack.

P1197E-861 User’s Manual
14 Hardware and Installation
2.5 HDD Installation
The P1197E-861 provides a convenient Hard Disk Drive (HDD) bracket for users to install 2 x
2.5”SATA HDD. Please follow the steps:
Step 1 Unscrew 1 screws to take off the HDD door.
Step 2 Unscrew two screws and pull the HDD out directly.