Balluff BNI EIP-950-000-Z009 User manual

BNI EIP-950-000-Z009
IP67 Module, Unmanaged Switch
User’s Guide

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
1 Notes for the user
1.1
About this guide
2
1.2
Structure of the guide
2
1.3
Typographical conventions
2
1.4
Symbols
2
1.5
Abbreviations
2
2 Safety
2.1
Intended use
3
2.2
Installation and startup
3
2.3
General safety notes
3
Hazardous voltage
3
3 Getting started
3.1
Connection overview
4
3.2
Mechanical connection
5
3.3
Electrical connection
5
3.4
Ethernet connection
5
4 Technical data
4.1
Dimensions
6
4.2
Mechanical data
6
4.3
Operating conditions
6
4.4
Electrical data
6
4.5
Ethernet port
7
4.6
LED indicators
7
Appendix
Product ordering code
8
Order information
8
Scope of delivery
8
Notes

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com 2
1Notes for the user
1.1 About this guide
The BNI EIP-950-000-Z009 serves as an unmanaged switch module for connecting to an
EtherNet/IP™ network. This module is IP67 protected and features a rugged metal IP67
housing. The device is ideal for use in harsh industrial environments.
1.2 Structure of the
guide
The guide is organized so that the sections build on one another.
Section 2. Basic safety informations.
Section 3: The main steps for installing the device.
Section 4: Technical data for the device.
…
1.3 Typographical
conventions
The following typographical conventions are used in this guide.
Syntax
Numbers
Decimal numbers are shown without additional indicators (e.g. 123),
Hexadecimal numbers are shown with the additional indicator hex (e.g. 00hex).
Cross references
Cross references indicate where further information on the topic can be found (see
Section 4 „Technical data“).
1.4 Symbols
Note, tip
This symbol indicates general notes.
Caution!
This symbol indicates a security notice which must be observed.
1.5 Abbreviations
BNI Balluff Network Interface
EIP Ethernet IP
EMC Electromagnetic compatibility
FE Function earth

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com
3
2Safety
2.1 Intended use
The BNI EIP-950-000-Z009 serves as an unmanaged switch module for connecting to an
EtherNet/IP™ network.
2.2 Installation and
startup
Note
Installation and startup are to be performed only by trained specialists. Qualified
personnel are persons who are familiar with the installation and operation of the
product, and who fulfills the qualifications required for this activity. Any damage
resulting from unauthorized manipulation or improper use voids the anufacturer's
guarantee and warranty. The Operator is responsible for ensuring that
applicable of safety and accident prevention regulations are complied with.
2.3 General safety
notes
Commissioning and inspection
Before commissioning, carefully read the operating manual.
The system must not be used in applications in which the safety of persons is dependent on
the function of the device.
Authorized Personnel
Installation and commissioning may only be performed by trained specialist personnel.
Intended use
Warranty and liability claims against the manufacturer are rendered void by:
Unauthorized tampering
Improper use
Use, installation or handling contrary to the instructions provided in this operating
manual
Obligations of the Operating Company
The device is a piece of equipment from EMC Class A. Such equipment may generate RF
noise. The operator must take appropriate precautionary measures. The device may only be
used with an approved power supply. Only approved cables may be used.
Malfunctions
In the event of defects and device malfunctions that cannot be rectified, the device must be
taken out of operation and protected against unauthorized use.
Intended use is ensured only when the housing is fully installed.
Hazardous
voltage
Note
Disconnect all power before servicing equipment.
Note
In the interest of product improvement, the Balluff GmbH reserves the right to
change the specifications of the product and the contents of this manual at any
time without notice.

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com 4
3Getting started
3.1 Connection
overview
Figure 3-1: Connection overview
1 Mounting hole
2 Ethernet Port 5
3 Status LED, transmission rate
4 Ethernet Port 6
5 Status LED, Link active
6 Ethernet Port 7
7 Ethernet Port 8
8 Ethernet Port 4
9 Ethernet Port 3
10 Ethernet Port 2
11 Ethernet Port 1
12 Label
13 Power supply
14 Ethernet Uplink Port
1
1
2
7
3
4
5
6
8
11
10
12
13
9
14

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com
5
3 Getting started
3.2 Mechanical
connection
The module is attached by using 2 M6 screws and 2 spacers.
Isolation pad as accessory available.
3.3 Electrical
connection
Supply voltage
Power (7/8 Mini 4-pin plug)
PIN
Signal
Demand
1
+24 V
Power 1
2
+24 V
Power 2
3
0 V
Power 2 Common GND
4
0 V
Power 1 Common GND
24 V DC.
Total current <9A. The total current of all modules may not exceed 9A even when daisy
chaining the actuator supply.
Function earth
Figure 3-2: FE connection
Note!
The FE connection from the housing to the machine must be low-impedance and
kept as short as possible.
3.4 Ethernet
connection
Ethernet Port: (M12, D coded, female)
PIN
Requirement
1
Tx+
2
Rx+
3
Tx-
4
Rx-

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com 6
4Technical data
4.1 Dimensions
Figure 4-1: Dimensions
4.2 Mechanical data
Housing material
Die-cast zinc, matte nickel plated
Enclosure rating per IEC 60529
IP 67 (only when plugged-in and threaded-in)
Supply voltage
7/8” 4-pin male
Dimensions (W x H x D in mm)
68 x 224 x 32.4
Mounting type
2-hole screw mount
Ground strap attachment
M4
Weight
Approx. 580gr.
4.3 Operating
conditions
Operating temperature Ta
Storage temperature
-5 °C ... 55 °C
-25 C ... 75 °C
EMC
- Immunity
- Emission
EMC-directive 2004/108/EEC
- EN 61000-6-2
- EN 61000-6-4
Shock / vibration
EN 60068-2-6, EN 60068-2-27
EN 60068-2-29, EN 60068-2-64
4.4 Electrical data
Supply voltage
18...30.2 V DC, per EN 61131-2
Ripple
<1%
Input current at 24 V
130 mA

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com
7
4 Technical data
4.5 Ethernet port
Ethernet IP Uplink port
1 x 10Base-/100Base-Tx
Connection for Ethernet IP Uplink port
M12, D coded
Standard Ethernet IP ports
8 x 10Base-/100Base-Tx
Connection for standard Ethernet ports
M12, D coded
Cable types per IEEE 802.3
Shielded twisted pair, min. STP CAT 5/ STP
CAT 5e
Data transmission rate
10 / 100 Mps
Max. cable length
100 m
Flow control
Half Duplex/Full Duplex
(IEEE 802.33x-Pause)
4.6 LED indicators
LED indicators
Ethernet IP /
module
LED
Indicator
Function
LED 1
Green / Red
Power Status
LED 4
Red / Off
Module Status
LED 7
Yellow / Off
Data transfer Uplink port active/inactive
LED 9
Yellow / Off
Data trans. rate Uplink port: 100Mbit/s / 50 Mbit/s
LED indicators
ports
Each M12 port is assigned LEDs which indicate the configuration or operating states.
LED LNK
Function
Off
Ethernet link is inactive
Green blinking
Data transfer is active
LED 100
Yellow / Off
Data trans. Rate: 100 Mbit/s / 50 Mbit/s
LED 1-9: Indication: Module / Uplink port
Port LED: Link
Port LED: Data transmission rate

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com 8
Appendix
Product ordering code
BNI EIP-950-000-Z009
Balluff Network Interface
IO-Link interface
Functions
950 = IP 67 module, unmanaged switch
Variant
000 = Standard version
Mechanical version
Z009 = Material: Die-cast zinc housing
Uplink: 1 x M12x1 internal thread
Power: 7/8“ external thread
Ethernet ports: 8 x M12x1 internal thread
Order information
Product ordering code
Order code
BNI EIP-950-000-Z009
BNI000F
Scope of delivery
The BNI EIP …consists of the following components:
IO-block
4 blind plugs M12
Ground strap
Screw M4x6
20 labels
User’s Guide

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com
9
Notes

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com 10
Notes

Balluff Network Interface / EtherNet/IP™BNI EIP-950-000-Z009
www.balluff.com
11
www.balluff.com
Balluff GmbH
Schurwaldstrasse 9
73765 Neuhausen a.d.F.
Germany
Tel. [phone]
Fax [phone]
[email protected]
www.balluff.com
Nr. 910590 E Edition 1312 Subject to modification