Barco Event Master E2 User manual

Event Master E2 –Screen Management System
Quick Start Guide
Input Cards Output CardsExpansion Cards MVR
M2
P/N 26-1205004-00 Rev 01
Ethernet Genlock
In Loop
SDISDISDI SDI
SDISDISDI SDI
DVIDVI
DVIDVI
DP
DPHDMIHDMI
DP
DPHDMIHDMI
DP
DPHDMIHDMI
DP
DPHDMIHDMI
HDMI
HDMIHDMIHDMI
SDISDISDI SDI
HDMI
HDMI
HDMIHDMI
CXPCXP
CXPCXP
123 4 56 7 8 910 11 12 13 14
H
Dual Redundant Power Supplies
H
123412
S3D
In S3D Out
Expansion Cards
- 2 High speed CXP connectors
SDI Input & Output Cards
- 4 SDI BNC connectors
- SD/HD/3G formats (6G ready)
DisplayPort/HDMI Combo Input Cards
- 2 DP and 2 HDMI locking connectors
- Displayport 1.1a specification
- HDMI 1.4a specification
- HDCP 1.4 & EDID 1.3
DVI Input Cards
- 2 DVI-I connectors (no analog signals)
- Single / Dual Link formats
- DVI 1.0 specification
- HDCP 1.4 & EDID 1.3
Quad Channel DisplayPort Output Cards
- 4 full-size DP locking connectors
- Up to 4 independent signals
- DisplayPort 1.2 specification
- HDCP will be supported in a future software
release.
HDMI Output cards (including MVR)
- 4 HDMI connectors (top 2 connectors capable of
high-speed HDMI signals up to 300 MHz)
- HDMI 1.4a specification
- HDCP 1.4 and EDID 1.3
M1
Be sure that you properly align the Link cable connectors prior to insertion.
Connectors should insert easily with almost no resistance, until the lock is
about to engage. Be sure that the lock engages fully to ensure proper
contact. Make sure that you use the locking mechanism and then push
each cable until it locks in place.
1. Connect the Link cables provided with each E2 between the Link
connectors as follows:
• VP ID 0, Link Card slot 1, Link 1 >> VP ID 1, Link Card slot 1, Link 2
• VP ID 0, Link Card slot 1, Link 2 >> VP ID 1, Link Card slot 1, Link 1
• VP ID 0, Link Card slot 2, Link 1 >> VP ID 1, Link Card slot 2, Link 2
• VP ID 0, Link Card slot 2, Link 2 >> VP ID 1, Link Card slot 2, Link 1
4. Start the Event Master Toolset
version 4.0 or higher.
5. Make sure that both E2s are
discovered on the network and that
they have different Unit IDs.
If the system does not discover your
device, you may manually add it. See
"How to manually add a device into
the selected system" in the user’s
guide.
6. Drop one of the E2s in the EM GUI.
Link Connections
Ethernet switch
PC with Event Master
Control Software
MVR
MVR
Refer to the Event Master devices User’s
guide (R5905948) for detailed system
specifications, descriptions and operation
instructions.
Any item contained in this document may
change without notice.
For the latest version of the Event Master
devices User’s guide (R5905948) and the E2 –
Screen Management System Quick Start
Guide (26-1205004-00), visit www.barco.com.
Power Switch
USB Port
SEL and ESC ButtonsADJUST KnobDisplay
System Setup
1. Ensure that the unit is physically secured in a
rack or is placed on a flat surface with stable
support. If the unit is installed in a rack, it is
mandatory that the rear brackets are also
installed.
2. Connect all sources, displays, and peripherals
to the E2 according to your event’s
requirements.
3. Connect AC power to the unit. If power
redundancy is desired, connect power to both
power plugs.
4. Connect to a computer that has the Event
Master control software installed, via an
Ethernet cable. A switch is optional if additional
devices will be connected.
5. Power up the E2, the PC, all monitors and
peripherals.
6. Verify that no error messages appear on the E2
front panel.
7. After the E2 boots up, run the Event Master
control software and follow the sequence of
instructions listed in this Quick Start Guide to
complete the system setup and configuration.
Should the system not fully boot correctly, press
and hold the SEL and ESC buttons while
applying power to the unit. Release these
buttons when a menu appears asking to Factory
Reset the unit. Perform the Factory Reset and
the unit will boot normally.
Dashboarda quick glance of your E2
Expansion
0Ready √Run Diagnostics
Expansion
1Ready √Run Diagnostics
Input
2Ready √Run Diagnostics
Input
3Ready √Run Diagnostics
Input
4Ready √Run Diagnostics
Input
5Ready √Run Diagnostics
Input
6Ready √Run Diagnostics
Input
7Ready √Run Diagnostics
Input
8Ready √Run Diagnostics
Input
9Ready √Run Diagnostics
Input
10 Ready √Run Diagnostics
Expansion
Slot ID Card Status Actions
Inputs Outputs Other
S1 S2 S3
SETTINGS MENU
S1: Options - On the Options tab
click on the boxes to select system
wide user preferences such as
Layer positioning.
S2: Tools - Allows users to
perform Backup and Restore
operations or download the latest
software from the Barco website
S3: Dashboard - Provides status
information regarding the cards
and other system diagnostic
information.
inputs, and they expand the number of layers and outputs. For more information on linking, see Section 6.17 "Configuration Menu > Linking in the Event
Master Devices User's Guide, or see the instructional videos on the Barco Folsom IP YouTube site.
For links to other quick-start guides and the Event Master Devices User's Guide, see the Technical Downloads tab for each product on the Barco
Presentation switchers page at: https://www.barco.com/en/Products/Image-processing/Presentation-switchers
Linking
An Event Master unit can link with other
Event Master units. Depending on the
linking configuration, linked units share
Barco Technical Support:
USA: [phone]
EMEA : 0800 90 0410
CHINA : 40088 22726
APAC: [phone]
www.barco.com/en/Support
For links to instructional videos, see the Barco Folsom IP YouTube site at: https://www.youtube.com/user/BarcoFolsomIP.
Notes:
- Input and Output cards each support
one 4K/UHD signal.
- This sample system shows the optional DP 1.2
Output card. The system does not ship with this
card; your configuration may be different.
- Cards are not hot-swappable.
Example: Linking a pair of E2s
1. Check the cable orientation for keying. The cable fits in only one orientation.
2. Fully insert the cable into the connector on the Link Card.
3. If the cable resists full insertion, do not force it; pull the cable out, check its
orientation, and reinsert it.
4. Make sure that the latch is properly engaged.
5. Always use the release when removing the cable.
Improper insertion or removal of Link cables can damage the
connectors and is not covered under the product warranty.
2. Make sure that the E2s have different IP addresses.
The default IP address for each unit is the same; one of them must be
changed.
3. Connect all devices to network Ethernet.
7. Drop the second E2 in the EM GUI.
The EM GUI presents the options of adding the second unit as a new system,
as a master, or a as a slave.
HDMI
HDMIHDMIHDMI
H
MULTIVIEWER (MVR)
MENU
M1: Select MVR Sources - From
the dropdown menus select the
Inputs, Backgrounds, and
Destinations you want to view
and drop them into Multiviewer
Outputs. Overlapping is not
allowed. An MVR source may be
used twice. A maximum total of
63 windows can be used for
Inputs and 63 windows can be
used for Outputs.
M2: Adjust Window - Adjust the
size, position and the color
parameters associated with each
window. Repeat for all Inputs and
save.

C3: System Parameters
(Native Rate, Genlock Mode, and Preset Conflict Mode)
C8:Add Screen
Destinations
Add Layers to
Destinations
C9:Add Aux
Destinations
C6: Add
Outputs
(Turn On Test
Patterns)
C4: Add
Backgrounds C5: Add
Inputs
P3: Create
Sources from
Inputs P6: Drop
Inputs/
Backgrounds
into Aux
Destinations
Multiviewer Menu (next page)
P2: Select
thumbnails
for Inputs
P1: Select
thumbnails
for
Backgrounds
C7: Add MVR
Outputs
P5: Drop Layers
into Screen
Destinations
&
Sources into
Layers
P4: Drop
Backgrounds into
Screen
Destinations
P7: Create User
Keys
P8: Create Presets
P/N 26-1205004-00 Rev 01
Refer to the User’s Guide for a detailed description of each step
Event Master Control Software Flowchart
C1: Discover
C2: Connect
CONFIGURATION MENU
C1: Discovery - When the Event Master control software loads, it
automatically discovers the devices connected to the network. These
devices are listed on the left hand side of the configuration screen.
C2: Connect - Click on the device you want to connect and drag it in the
middle area. The software should automatically establish communication
with the unit. If connection between the PC and the E2 is not achieved, re-
check the wire connection. On the Configuration Menu, ensure that the IP
settings match with the E2 settings that are available from the front panel.
You can also connect to the E2 by typing the IP address manually.
C3: System Parameters - Select the desired Native Rate, Genlock Mode,
and Preset Conflict Mode.
C4: Add Backgrounds - Select and define input connectors as a
background. Select the Adjust tab and perform any additional adjustments.
Repeat for all Backgrounds and save. Max of 8 connectors of the same
type can be assigned per background (Except for DVI & HDMI).
C5: Add Inputs - Select and define input connectors as Inputs. Select the
Adjust tab and perform any additional adjustments. Repeat for all Inputs
and save. Max. of 4 connectors of the same type can be assigned per
input.
C6: Add Outputs - Select and define output connectors as Outputs. Select
the Adjust tab and perform any necessary adjustments.
Repeat for all Outputs and save. Max. of 4 connectors of the same type
can be assigned per output.
Output Test Patterns (Optional) - Under the Adjust and Output tabs select
the test patterns on one or more outputs, to assist with external device
setup
C7: Add Multiviewer Outputs - Select connectors from the MVR slot and
define them as a MVR Output. Repeat for all Outputs and save.
C8: Add Screen Destinations - Select the corresponding output
connector(s) from the same card and add them to Screen Destinations via
drag and drop. From the Adjust tab, add the number of desired layers and
perform any necessary adjustments. Repeat for all Screen Destinations
and save.
C9: Add Aux Destinations - Select the corresponding output connector(s)
from the same card and add them to Aux Destinations. Select the Adjust
tab and perform any necessary adjustments. Repeat add all Aux Screen
Destinations and save.
C1
C2
C3
C8,9C6
C7
C4
C5
P1
P7
P6
P2
P3
P4
P5
System Initialization
Return to Factory Default (Optional) - For a new event, back up your system if desired, then perform a complete factory reset. For a continuing (or multi-day)
event, this step is not required.
Restoring the System (Optional) - Insert a USB drive with a previous backup file into the USB Port. On the Backup and Restore Menu, press {Restore
System} and follow the prompts.
Backing up the System (Optional) - Insert a USB drive into the USB Port. On the Backup and Restore Menu, press {Backup System} to back up the system
setup and all memory registers.
Factory Reset, System Backup and Restore - Operations can be performed from the Events Master Control software or from the front panel.
PROGRAMMING MENU
P1: Select thumbnails for Backgrounds - Press Refresh All, or select the
thumbnails to represent the Backgrounds.
P2: Select thumbnails for Inputs & Stills - Press Refresh All, or select the
thumbnails to represent Inputs and Stills
P3: Create Source Files - Under the Input tab create any additional source
files (optional). Select the Adjust tab and perform any additional
adjustments and press Save. Repeat for all Inputs/Sources and save.
P4: Drop Backgrounds into Screen Destinations - Under the Background
tab select a Background and drop it to a Screen Destinations. Repeat for
all Backgrounds and save.
P5: Drop Layers & Sources - Under the Layer tab select a layer and drop
it to a Screen Destination. Select a Source under the Input tab and drop it
into the layer. Alternatively, select a source and drag it to the destination to
automatically show the layer with the selected source. Select the Adjust tab
and perform any additional adjustments. Repeat for all layers and sources
and save.
P6: Drop Inputs \ Backgrounds to Aux Destinations - Under the Input or
Background tabs select a Input \ Background and drop it to the Aux
Destinations. Select the Adjust tab and perform any additional adjustments.
Repeat for all Backgrounds and save.
P7: User Keys - Select a layer and under Adjust and User Keys tabs click
on the Enables to save. Repeat for all desired User Keys and save.
P8: Presets - Select Screen(s) and under Adjust and Preset tabs create a
new preset or manage existing ones. Repeat to create multiple Presets.
P8