Barco Lamp House with 2.5 kW lamp User manual

Lamp House with 2.5 kW lamp
Installation manual
For HDX series
R9864130
R5905109/02
21/09/2011

Barco nv Events
Noordlaan 5, B-8520 Kuurne
Phone: [phone]
Fax: [phone]
Support: www.barco.com/esupport
Visit us at the web: www.barco.com
Printed in Belgium

Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-
ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the
program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com or from the secured Barco web site
https://my.barco.com.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Disposal Information
This equipment has required the extraction and use of natural resources for its production. It may contain hazardous substances for health
and environment. In order to avoid the dissemination of those substances in the environment and to diminish the pressure on natural
resources, we encourage you to use the appropriate take-back systems. Those systems will reuse or recycle most of the materials of your
end of life equipment in a sound way.
The crossed-out wheeled bin symbol invites you to use those systems. If you need more information on the collection, reuse and recycling
systems, please contact your local or regional waste administrator. You can also contact us for more information on the environmental
performances of our products.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.

Table of contents
TABLE OF CONTENTS
1. Lamp House with 2.5 kW lamp.................................................................................. 3
1.1 Introduction .......................................................................................................................... 3
1.2 Safety ................................................................................................................................ 3
2. Lamp and Lamp House........................................................................................... 5
2.1 Removal of the Lamp House........................................................................................................5
2.2 Installation of the Lamp House...................................................................................................... 6
2.3 Realignment of the lamp in the Lamp House ....................................................................................... 7
R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011 1

Table of contents
2R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011

1. Lamp House with 2.5 kW lamp
1. LAMP HOUSE WITH 2.5 KW LAMP
Purpose of the Lamp House with 2.5 kW lamp
The Lamp House with 2.5 kW lamp is exclusively designed for the Barco HDX series and can thus not be used on any other equip-
ment.
Overview
• Introduction
• Safety
1.1 Introduction
Order info & content of the kit
When ordering the Lamp House with 2.5 kW lamp for HDX series, refer to article number R9864130.
The table below gives an overview of the content of the kit.
Article number Description Quantity Image
R5905109 This installation manual 1 image 1-1
R856950 Lamp House with 2.5 kW lamp 1 image 1-2
Image 1-1 Image 1-2
1.2 Safety
Safety instructions
Read and heed the following warnings and cautions.
WARNING:The procedures below may only be performed by Barco trained and qualified technicians.
WARNING:The projector must be cooled down before removing any of the projector covers: wait for the cool
down cycle to finish after switching the projector to standby (the sound of the fans comes to a very low level)
and wait for 15 more minutes before starting any of the procedures below.
WARNING:Unplug the mains power supply cord in order to completely cut off the power supply to the pro-
jector. Failure to do so can cause serious injury or death.
R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011 3

1. Lamp House with 2.5 kW lamp
CAUTION:Always wear a wrist band which is connected to the ground while handling the electrostatic dis-
charge (ESD) sensitive parts.
4R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011

2. Lamp and Lamp House
2. LAMP AND LAMP HOUSE
About this chapter
This chapter describes how to remove and install the complete Lamp House. Furthermore, instructions on how to align the lamp to
maximize the light output are given.
Image 2-1
Overview
• Removal of the Lamp House
• Installation of the Lamp House
• Realignment of the lamp in the Lamp House
2.1 Removal of the Lamp House
WARNING:The procedures below may only be performed by Barco trained and qualified technicians.
Necessary tools
7mmflat screwdriver
How to remove the Lamp House?
1. Switch off the projector and unplug the power cord at the projector back side.
2. Let the projector cool down for at least 15 minutes before proceeding to the next step.
Warning: The Lamp House is very hot after operation. Let the projector cool down for at least 15 minutes before proceeding
to the next step. Failure to do so can cause serious injury.
3. Remove the right projector cover. See the installation manual of the projector.
4. Release the 3 captive screws on the Lamp House.
R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011 5

2. Lamp and Lamp House
Image 2-2
5. Take the Lamp House by its handles and pull it out of its compartment.
Image 2-3
Note: While starting up the projector, the electronics detect if a Lamp House is installed. If no Lamp House is installed, it is not
possible to start up the projector.
2.2 Installation of the Lamp House
WARNING:The procedures below may only be performed by Barco trained and qualified technicians.
Necessary tools
7mmflat screwdriver
How to install the Lamp House?
1. Take the Lamp House by its handles and gently slide it in its compartment.
Tip: The compartment is provided with a guide to position the Lamp House correctly.
6R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011

2. Lamp and Lamp House
Image 2-4
2. Push the Lamp House forward until it slides fully into the projector. The positioning pins must match the holes in the Lamp House.
3. Secure the 3 captive screws on the Lamp House.
Image 2-5
4. Install the right projector cover. See the installation manual of the projector.
5. Plug in the power cord at the projector back side.
Note: While starting up the projector, the electronics detect if a Lamp House is installed. If no Lamp House is installed, it is not
possible to start up the projector.
2.3 Realignment of the lamp in the Lamp House
WARNING:The procedures below may only be performed by Barco trained and qualified technicians.
It is recommended to realign the Z-axis of the lamp after the first run time of 100 and 200 hours.
R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011 7

2. Lamp and Lamp House
Necessary tools
7 mm open-end wrench
How to realign the lamp in the Lamp House?
1. Switch off the projector.
2. Let the projector cool down for at least 15 minutes before proceeding to the next step.
Warning: The Lamp House is very hot after operation. Let the projector cool down for at least 15 minutes before proceeding
to the next step. Failure to do so can cause serious injury.
3. Remove the right projector cover. See the installation manual of the projector.
4. Switch on the projector and startup the lamp.
5. Press Menu to activate the menus and select Lamp →Z-axis.
Image 2-6
Main menu, lamp
Image 2-7
Lamp, Z-axis
6. Press ENTER to display the current light output.
Image 2-8
Current light output
7. Release the lock nuts for the X-axis, Y-axis and Z-axis..
8. Adjust the X, Y and Z-axis for maximum light output. Carefully turn the thumbscrews in one direction, and once over the maximum,
turn slightly in the opposite direction to reach the maximum light output again. Do this for each direction and repeat this adjustment
cycle minimum twice.
9. Tighten the lock nuts for the X-axis, Y-axis and Z-axis.
8R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011

2. Lamp and Lamp House
43
6
21 5
Image 2-9
1Xlock
2 X adjustment
3Ylock
4 Y adjustment
5Zlock
5 Z adjustment
10.Switch off the projector.
11.Install the right projector cover. See the installation manual of the projector.
R5905109 LAMP HOUSE WITH 2.5 KW LAMP 21/09/2011 9