Barco R9841770 User manual

Lamp Kit for iQ/SIM4 Projectors
Installation Manual
R9841770 - R9841771
R9841100 - R9841111
R9841760 - R9841761
R5976375/03
23/06/2004

Barco nv Intelligent Displays
Noordlaan 5, 8520 Kuurne
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Visit us at the web: www.barco.com
PrintedinBelgium

Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may
cause harmful interference, in which case the user will be responsible for correcting any interference.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.

1. Safety
1. SAFETY
1.1 Safety Guidelines
This procedure is intended for use only by qualified service technicians who have been trained and authorized
by BARCO !
WARNING:Hot Surface and Risk of Explosion:Switch the projector to stand by and let it cool down for at least
15 minutes . These lamps consist of a quartz arc tube operating at very high temperature and high pressure
(200 bar) which may explode suddenly. There is a risk of personal injury and property damage from hot quartz
arc tube particles if handled incorrectly.
WARNING:Risk of Electrical Shock: Power down the projector and unplug the power cord from the wall
outlet. Once the projector is cooled down and the power is off, continue with the procedure.
WARNING:Lamp Runtime Warning: Do not exceed the indicated maximum total lifetime of the lamp for safe
operation in normal power mode. Do not use it longer ! Always replace the lamp with the BARCO lamp kit.
R5976375 LAMP KIT FOR IQ/SIM4 PROJECTORS 23/06/2004 1

1. Safety
2R5976375 LAMP KIT FOR IQ/SIM4 PROJECTORS 23/06/2004

2. Kit Content
2. KIT CONTENT
2.1 Contents
Overview
Depending on the Kitnumber ordered the kit may contain 1 or 2 lamps, the lamp power may also differ according to the type of
Projector.
Kitnumber Description Quantity Manual
R9841771 120 W Lamp 1R5976375
IQ200
R9841770 120 W Lamp 2R5976375
R9841111 200 W Lamp 1R5976375
IQ300/MGP10/SIM4
R9841100 200 W Lamp 2R5976375
R9841761 250 W Lamp 1R5976375
IQ350/400/5001
R9841760 250 W Lamp 2R5976375
Image 2-1
CAUTION:Do not touch the cover glass with your fingers. If the lamp is touched, finger prints can be removed
by cleaning the lamp with alcohol.
1. The 350 uses the 250 lamp on 200W only
R5976375 LAMP KIT FOR IQ/SIM4 PROJECTORS 23/06/2004 3

2. Kit Content
4R5976375 LAMP KIT FOR IQ/SIM4 PROJECTORS 23/06/2004

3. Replacement procedure in case of an iQ Projector
3. REPLACEMENT PROCEDURE IN CASE OF AN IQ
PROJECTOR
Overview
• Reset lamp runtime
• Access to the lamp unit(s) in the iQ projector
• Removing the lamp unit(s)
• Mounting the Lamp Unit
• Mounting the cover.
• Cleaning
3.1 Reset lamp runtime
3.1.1 Reset runtime
When to reset the lamp runtime ?
The lamp runtime should only be reset when placing a new lamp.
How to reset the lamp runtime ?
1. Press MENU to activate the Toolbar
2. Press →to select the Lamp item
3. Press ↓to Pull down the Lamp menu
4. Use ↑or ↓to select Reset runtime
5. Press →to pull down the menu
6. Use ↑or ↓to select the lamp to be reset (image 3-1)
7. Press ENTER
A dialogbox is displayed (image 3-2)
8. Use ←or →, the numeric keys on the remote, or the keypad to change the serial number of the lamp (serial number 0000000 will
not be accepted).
Image 3-1
Image 3-2
R5976375 LAMP KIT FOR IQ/SIM4 PROJECTORS 23/06/2004 5

3. Replacement procedure in case of an iQ Projector
WARNING:Lamp runtime reset as well as the lamp replacement can only be done by a Barco authorized
technician.
3.2 Access to the lamp unit(s) in the iQ projector
3.2.1 Removing the back cover
Necessary tools
a flat screwdriver of 10 mm
Necessary parts
No parts.
WARNING:Risk of Electrical Shock: For replacement procedures power down the projector and unplug the
power cord from the wall outlet. Once the projector is cooled down and the power is off, continue withthe
replacement procedure.
Removing the back cover
1. Turn with a screwdriver the cover lock screw A quarter turn counter clockwise. (image 3-3)
2. Remove the back cover.
See image 3-4, image 3-5.
Image 3-3
rear cover lock screw Image 3-4
rear cover removed
Image 3-5
right view of the projector, rear cover removed
6R5976375 LAMP KIT FOR IQ/SIM4 PROJECTORS 23/06/2004