BDI MARGO 5229 User manual

1
Product Registration
Registering your new BDI product allows us to send you
important product updates, service information and helpful hints
related to your BDI products. Register today, and you will be
entered to win a free BINK table from BDI:
www.bdiusa.com/register
Placement and Maintenance
Your Margo Cabinet is designed for indoor use on level floors.
Clean all surfaces with a damp cloth.
Margo is engineered for easy assembly. Carefully follow this
procedure to prevent any damage. Do not use power tools
for assembly of this product.
Step 1
Unpack and identify the parts listed below. The assembly
workspace should be a non-marring surface such as carpet.
For missing hardware pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by Jeff Bare.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Margo & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2018, BDI
Patent:
Made in China. 08.06.2019 V3
MARGO™5229
Cabinet
Tool Required:
Phillips Screwdriver
C1 Cabinet x 1
C2 Shelf x 1
A1 Base Rail x 1
A3 Right Leg x 1
C3 Door Fascia x 1
T1 Hex driver x 1
T2 Small Hex wrench x 1
Component List
H3 Thumb Screw x 2
H1 M6 x 12mm
Screw x 4
A2 Left Leg x 1
H2 M6 x 72 mm
Screw x 7
H5 TV Safety Strap x 1
H4 5/16 x 5/8"
Screw x 1

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
2
Step 2 - Assemble the base
Position base rail A1 on a padded floor as shown. Orient the left and right legs as shown and slide the leg tabs
into the ends of the base rail. Attach leg to base rail with screws H1 and hex driver T1.
Do not fully tighten the screws yet.
A2 Left Leg
A3 Right Leg
A1
H1 x 4
T1
pairs of holes
facing you

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
3
Step 3 - Attach the base
With help from another person, carefully position the cabinet on its back. Attach the base using screws H2 and
hex driver T1 going through the holes on the base and into the threaded holes on the bottom of the cabinet.
Now fully tighten leg to base rail screws.
2 Person Ta sk
2 Person Ta sk
T1
H2 x 7
Step 4 - Stand Up
With help from another person, and making sure the door does not slide, carefully position the cabinet onto
its base.
secure door
before moving the
cabinet

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
4
Step 5- Attach Door Facia
Slide the door frame towards the middle. Orient the door fascia C3 as shown with the threaded holes
behind the left side. Position the door fascia C3 into the door frame and shift it to the right while holding the
left edge of the door frame to prevent it from sliding. Secure the left side of the door fascia to the door frame
with 2 thumb screws H3 going into the holes on the back of the door frame and into the threaded holes on
the back of the door fascia C3.
Caution: Before sliding the door, check to make sure the door facia is not rubbing on either the top or bot-
tom edge of the cabinet. If it is, proceed to step 6. If your door is level and the gaps on the top and bot-
tom are even, proceed to step 7.
Door frame
threaded holes
this side
Door fascia
C3
H3
H3
slide to the right
to lock

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
5
turning the wheel
horizontally
adjusts the corresponding
door corner
up or down
Step 6 - Adjust sliding door (if needed)
If your sliding door is not hanging evenly, or rubs at the top or bottom, it can be adjusted up or down by turning
one (or both) adjustment wheels inside the cup (located behind each upper corner of the door). To access
the adjustment wheel behind the right side of the door, remove the door facia by following step 5 in reverse.
To move the door frame up turn the wheel towards the left. To move the door frame down, turn the wheel
towards the right. Lifting the door frame up with your other hand allows the adjustment wheel to turn more
freely.
turn wheel
lift gently
adjustment
wheel
wheel
direction
door direction

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
6
3/4"
19mm
Step 7 - Door Stops
Your Margo Console sliding door has 2 green door stops located at each end of the upper aluminum track.
The door stops are preset to allow the door to stop in the correct position. If your door(s) do not stop at the
preset position indicated below, it is likely they may have moved during transit and handling. You will need
to reposition and tighten the door stop using Small Hex Wrench T2. The end of the door stops should be
exactly 19mm (3/4") away from the end of the track.
Edge of green door stop
should be 19mm (3/4") away
from end of track.
Use Small Hex Wrench T2
to tighten door stop in correct
position.
Correct Door Stop
Position
Incorrect Door Stop
Position
Door Stop
T2

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
7
Step 8 - TV Safety Strap
Your Margo Cabinet is equipped with a TV safety strap. If using a TV, attach the TV safety strap H5 to the
back of the cabinet with screw H4, unravel and connect the 2 loose ends of the Y strap to your TV.
See hang tag for details.
Shelf Pins
Levelers
C2
TV Saftely Strap
Step 9 - Adjust shelves / Level your unit
The cabinet shelf C2 is adjustable. Shelf pins may be unscrewed and moved up or down.
Levelers are integrated into each leg assembly and are accessed at the bottom of each leg. If your floor is
uneven, you may extend one or more levelers to attain a level, stable cabinet position.
H4
H5

bdiusa.com
customerservic[email protected]om
MARGO 5229
CABINET
8
Step 10 - Drawer Adjustment
The 2 drawers on your Margo Cabinet are adjustable as much as 2mm up, down, left, right, back or forward.
If the drawers are out of alignment, follow the steps below:
3) Pushing the orange lever towards the outside
wedges the drawer up. Pulling it towards the
middle of the drawer makes the drawer drop.
2) Rotating the white wheel towards you moves the
drawer to the left. Rotating away moves it right.
1) Rotating the black wheel towards the inside of
the drawer moves the drawer backward, deeper
into the cabinet.
Left
Right
Up Down
Backward
Forward