BDI TANAMI 7109 User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a
BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Tanami Credenza is designed for indoor use on level floors.
Clean painted surfaces and steel parts with a moist cloth.
Tanami is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of this
product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing hardware
pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by BDI Studio.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Tanami & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2016, BDI
Made in China. 05.25.2017
TANAMI™7109
CREDENZA
A1 Cabinet x 1
C1 Shelf x 4
H4 TV Saftely Strap x 1
A2 Base Rail x 1
A3 Leg x 2
T1 Hex Wrench x 1
H1 1/4-20 x 25 mm
Flathead Screw x 8
H2 1/4-20 x 12 mm
Screw x 8
H5 5/16-18 x 15 mm
Screw x 1
H3 1/4-20 x 80 mm
Screw x 2

bdiusa.com
customerservic[email protected]om
TANAMI 7109
CREDENZA
2
Step 2 - Assemble the base
Attach the 2Legs A3 to Base Rail A2 with 4Flathead Screws H1 using Hex wrench T1. Make sure the
countersunk holes on the legs are positioned on the outside.
Step 3 Attach the base
With help from another person, carefully position the cabinet on its back. Attach the base using 8 screws H2
going through the plates and 2 screws H3 going through the base rail and into the threaded holes on the
bottom of the cabinet.
A2
2 Person Ta sk
T2
H1
T1
H2 x 8 H3 x 2
A3
A3
H1 x 4
A1

bdiusa.com
customerservic[email protected]om
TANAMI 7109
CREDENZA
3
Step 4 Stand Up / Adjust shelves
With help from another person, carefully position the cabinet onto its base. Check to make sure the cabinet
is level and that all legs are touching the ground. Adjust levelers if needed. The upper shelves in your Tanami
Credenza are adjustable. Shelf pins may be unscrewed and moved up or down.
STEP 5 - Level your unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg. If your floor
is uneven, you may extend one or more levelers to attain a level, stable cabinet placement. Turning the leveler
clockwise will extend the leveler; turning it counter-clockwise will retract it.
2 Person Ta sk
C1 C1 C1 C1
down

bdiusa.com
customerservic[email protected]om
TANAMI 7109
CREDENZA
4
Step 6 Attach the TV Safety Strap
If you intend to place a TV on your Tanami Console, it is strongly recommended that you install the TV Safety
Strap. Insert the triangular bracket through the left side of the center upper slot on the back of your console as
shown.
Open the third door (from the left) and attach the triangular bracket into the insert on the upper left corner using
the 5/16-18 x 15mm screw H5. Follow the instructions on the hang tag attached to the safety strap to secure
your TV.
H5
H5
Triangular bracket
on end of safety
strap

bdiusa.com
customerservic[email protected]om
TANAMI 7109
CREDENZA
5
STEP 7 - Adjust Door Hinges (if needed)
The doors on your cabinet should be evenly spaced and the doors should open and close freely without rubbing
against the door frame. If the cabinet’s doors appear out of alignment, this condition can be corrected with minor
adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can
modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet.
Example:
Tightening screw 1
on top hinge will move the
top of the door in the
direction shown
Example:
Adjusting screw 2
on both hinges (same direction)
will move the door up or down
Use the Phillips Screwdriver T1 supplied to adjust the door hinges:
• By adjusting Screw 1, the door will move LEFT or RIGHT within the
frame. Make minor adjustments at both top and bottom hinges for
best results.
• By adjusting Screw 2, the door will move UP or DOWN. For best
results, adjust Screw 2 on both the top and bottom hinges.
• By adjusting Screw 3 the entire door will move IN or OUT, opening
or closing the gap between the door frame and cabinet. (This screw
rarely needs adjustment.)
123