BDI Sequel User manual

PLEASE FOLLOW
THESE INSTRUCTIONS
CAREFULLY.
ATTENTION:
PENINSULA
6018
SEQUEL
®
OFFICE
Sequel Peninsula 6018
Assembly and Placement Information
BDIUSA.COM

2
desk and return

3
Thanks for purchasing the
Sequel System.
Before you begin setting up the Sequel System Components,
it is imperative that you read the Consumer Considerations
section on the next page.
features

4
Consumer Considerations
Plan your space.
Forethought is essential in determining the placement of each
component. Using a measuring tape, determine how much
floor space each unit will require. A cardboard template has
been provided in order to help aid this process.
Get someone to help you.
Help from a second person is required for the majority of the
steps outlined in this instruction manual.
AC power outlet and wire management
Depending on the configuration of your office set up, the Sequel
cabinet may end up resting in front of an AC power outlet. If
so, be sure to plug in the AC power strip, phone/ethernet or
extension cords prior to placing the cabinet in its final position.
Placement
Once the Sequel System is fully assembled, it cannot be moved.
Make all positioning adjustments prior to final assembly.
Leveling
SEQUEL Furniture is designed for indoor use on level floors. If
the floors are uneven, adjust levelers as necessary.
Tempered glass.
Exercise caution while handling the glass, and be sure to
employ the help of another person. Keep edges of glass panels
away from hard surfaces in order to prevent breakage.

5
Consumer Considerations
Power & Placement
This page outlines two scenarios:
Scenario 1
If cabinet is NOT blocking an AC power
outlet, it may be positioned close to the wall.
Power
Top View
Scenario 2
If cabinet is going to block an AC power
outlet, position cabinet approximately 3” from
wall. Low profile extension plugs may be
used to reduce the amount of space required
in this application.
3" Power
Top View

6
I
G
E
D
F
H
C
G
H
D
H
H
F
Peninsula
Model 6018
Your SEQUEL®6018 Furniture is engineered
for easy assembly.
Carefully follow this procedure to prevent
any damage.
Do not use power tools for assembly of this product.
NOTE: This instruction sheet is intended
for both the Left and Right Peninsula 6018;
the Right is shown for illustration.
Placement and
Maintenance
SEQUEL®6018 Furniture is designed for
indoor use on level floors. Clean glass with
glass cleaner, and steel parts and wood
veneer with a moist cloth.
Unpack and identify the components.
The assembly workspace should be a
non-marring surface such as carpet. For
missing hardware pieces, please contact
BDI Customer Service at customerservice@
bdiusa.com. For all other concerns, please
contact your BDI Retailer.
AHex Wrench 4mm x 1
B
Hex Wrench 3mm
x 1 (for Leveler
adjustment)
C
1/4-20 5/8” Machine
Screws 4mm Socket
Drive x 2
D
1/4-20 1/2” Flat Head
Screws 4mm Socket
Drive x 2
ERubber Stem Bumpers
x 5
F
1/4-20 60mm Machine
Screws 4mm Socket
Drive x 4
GDesk Frame Assembly x 1
HRound Legs x 2
IGlass Top x 1
JLeveler x 2
KVelcro Strap x 6
LPlastic Clip x 6
step 1
J
J
C
E
I
G
G

7
Wire Management
(Optional)
For the purpose of wire management, use
Plastic Clip (L) to install Velcro Straps (K) to
outside perimeter of Desk Frame Assembly
(G).
step 2
K x 6
L x 6

8
Attach Leg to Desk
Frame
While the second person holds the desk
frame on its side position, attach Round
Leg (H) to the underside of Desk Frame
Assembly (G) using the Hex Wrench (A)
and Machine Screws (C).
A
C x 4
G
H
step 3

9
Attach Desk Frame
to Cabinets
With the help of another person, carefully
lower Desk Frame Assembly (H) onto the
adjacent cabinets (Sequel Models 6014,
6015, 6016, or 6017). Adjust frame so that
the holes are aligned with the threaded
inserts on top of the cabinets. Once holes
are aligned, install Flat Head Screws (D)
using Hex Wrench (A).
A
D x 2
step 4

10
step 4
Bumpers
Install Rubber Stem Bumpers (E). E x 5
step 5

11
step 6
Install Glass
With the help of another person, carefully
lower the Glass Top (I) onto the frame.
Register the steel discs on underside of
glass into the holes on the frame; then
attach the glass using Machine Screws (F)
and Allen Wrench (A).
NOTE: Do not over-tighten screws!
A
F x 4

12
Install Glass
Carefully lower the glass panel onto the
Sequel Cabinet (Refer to individual cabinet
instructions).
step 7
1"
Plan View
When setting up multiple
workstations, leave at least
1" between each station.
Failure to do so may result in
damage to tempered glass
work surfaces.
CAUTION:
Designed by Matthew Weatherly.
These distinctive product configurations are protected
by US and international patents, trade dress, and/or
copyright laws. “Sequel” and BDI are trademarks of
Becker Designed, Inc. All Rights reserved. ©2011, BDI
Made in Taiwan. 6018REV052611v1
BDIUSA.COM