Bend-Pak Clearfloor 10AP User manual

1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free: [phone]
Telephone: [phone]
bendpak.com
Clearfloor Two-Post Lifts
Installation and Operation Manual
Manual P/N 5900265 — Manual Revision A6 — December 2022
Models:
•10AP
•10AP-168
•10APX
•10APX-181
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠
DANGER
IMPORTANT SAFETY INSTRUCTIONS, SAVE THESE
INSTRUCTIONS!
Read this manual thoroughly before installing,
operating, servicing, or maintaining this Lift. Failure to follow the instructions
and safety precautions in this manual can result in serious injury or death.
Make sure all other operators also read this manual. Keep the manual near
the product for future reference. By proceeding with installation and
operation, you agree that you fully understand the contents of this
manual and assume full responsibility for product use
.
10AP model shown.

Manual. 10AP Series Two-Post Lifts, Installation and Operation Manual, Manual Part Number 5900265, Manual
Revision A6, released December 2022.
Copyright. Copyright © 2022 by BendPak Inc. All rights reserved. You may make copies of this document if you
agree that: full attribution goes to BendPak Inc., you are not authorized to make changes to the content, you do
not gain any rights to this content, and you will not use the copies for commercial purposes.
Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,
product, and service names are used for identification only. All trademarks and registered trademarks mentioned
in this manual are the property of their respective owners.
Limitations. Every effort has been made to ensure complete and accurate instructions are included in this
manual. However, product updates, revisions, and/or changes may have occurred since this manual was
published. BendPak reserves the right to change any information in this manual without incurring any obligation for
equipment previously or subsequently sold. All drawings are reference only – do not scale. BendPak is not
responsible for typographical errors in this manual. You can always find the latest version of the manual for
your product on the BendPak website.
Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of
your new product. Contact your nearest BendPak dealer or visit www.bendpak.com/support/warranty for
full warranty details. Go to bendpak.com/support/register-your-product/ and fill out the online form to
register your product (be sure to click Submit).
Safety.Your Lift was designed and manufactured with safety in mind. Your safety also depends on proper
training and thoughtful operation. Do not set up, operate, maintain, or repair the Lift without reading and
understanding this manual and the labels on the unit;
do not use your Lift unless you can do so safely!
Owner Responsibility. In order to maintain your product properly and to ensure operator safety, it is the
responsibility of the product owner to read and follow these instructions:
• Follow all installation, operation, and maintenance instructions.
• Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,
such as state and federal OSHA regulations and electrical codes.
• Read and follow all safety instructions. Keep them readily available for operators.
• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.
• Do not operate the product until you are certain all parts are in place and operating correctly.
• Carefully inspect the product on a regular basis and perform all maintenance as required.
• Service and maintain the unit only with approved replacement parts.
• Keep the manual with the product and make sure all labels are clean and visible.
•BendPak makes no promises, guarantees or assurances that our products meet any state, county, federal or
international mandated permit, license, code, standard, certification, or any other mandate other than what is
listed or shown on BendPak website(s), or any BendPak or Ranger online or published catalog. Not all
BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201.
Consult www.autolift.org for a complete list of lift models that meet ANSI/ALI ALCTV-(current edition) or
ANSI/UL 201, or contact BendPak via [email protected].
Buyer assumes full responsibility
for any state, county, federal or international mandated permit, license, code, standard,
certification, or any other mandate required related to the installation and/or operation of
any BendPak product.
BendPak will not be responsible for any charges, fines, liens, or other levies
imposed on the Buyer related to any special or regional structural, seismic or any other building code and/or
codes such as the Uniform Building Code (UBC), International Building Code (IBC), or any other state, county,
federal or international mandated permit, license, code, standard, certification, or other mandate, law, rule,
regulation or directive by any other agency, government, administrations, or corporations whether state,
county, federal, or international mandated.
Only use the Lift if it can be used safely!

10AP Series Two-Post Lifts 3P/N 5900265 — Rev. A6 — December 2022
Unit Information.
Enter the Model Number, Serial
Number
, and the Date of Manufacture from the ID label
on your unit
. This information is required for part or
warranty issues.
Model:
Serial:
Date of Manufacture
:

10AP Series Two-Post Lifts 4P/N 5900265 — Rev. A6 — December 2022
Table of Contents
Introduction 4 Maintenance 69
Shipping Information 5 Troubleshooting 71
Safety Considerations 5 Wiring Diagrams 74
Components 8 Labels 75
Specifications 9 Parts Drawings 78
Installation Checklist 11 ALI Store 94
Installation 12 Maintenance Log 95
Operation 61
Introduction
This manual describes the four BendPak Two-Post Lift models:
•10AP. A Two-Post Lift with overall height of 145 in. / 3,683 mm that raises Vehicles up to 10,000
pounds (4,536 kg).
•10AP-168. A taller version of the 10AP with overall height of 168 in. / 4,267 mm, designed to
accommodate taller Vehicles.
•10APX. A Two-Post Lift with overall height of 157 in. / 3,988 mm that raises Vehicles up to
10,000 pounds (4,536 kg).
•10APX-181. A taller version of the 10APX with overall height of 181 in. / 4,597 mm, designed to
accommodate taller Vehicles.
All models have Overhead Assemblies and clear floors. All models may be adjusted to a narrow
92-inch (2,337 mm) or a wide 102-inch (2,591 mm) drive-through dimension.
⚠DANGER Be very careful when installing, operating, maintaining, or repairing this equipment;
failure to do so could result in property damage, product damage, injury, or (in very
rare cases) death. Make sure only authorized personnel operate this equipment. All
repairs must be performed by an authorized technician. Do not make modifications
to the unit; this voids the warranty and increases the chances of injury or property
damage. Make sure to read and follow the instructions on the labels on the unit.
More information about the full line of BendPak products is available at bendpak.com.
This manual is mandatory reading for all users of 10AP Series Two-Post Lifts, including
anyone who installs, operates, maintains, or repairs them. Keep this manual on or near the equipment
at all times.
Technical support and service is available from your dealer, on the Web at bendpak.com/support,
by email at [e-mail], or by phone at [phone], extension 196. You may
also contact BendPak for parts replacement information (please have the model and serial number of
your unit available) at [phone], extension 191.

10AP Series Two-Post Lifts 5P/N 5900265 — Rev. A6 — December 2022
Shipping Information
Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect
the shipment
before you sign to acknowledge that you received it.
When you sign the bill of lading, it tells the carrier that the items on the invoice were received in good
condition.
Do not sign the bill of lading until after you have inspected the shipment. If any of the
items listed on the bill of lading are missing or damaged, do not accept the shipment until the carrier
makes a notation on the bill of lading that lists the missing or damaged goods.
If you discover missing or damaged goods after you receive the shipment and have signed the bill of
lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not
make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a
specific date) and that the carrier has failed to comply with your request.
It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this
happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of
lading, freight bill, invoice, and photographs, if available. Our willingness to assist in helping you
process your claim does not make us responsible for collection of claims or replacement of lost or
damaged materials.
Safety Considerations
Read this entire manual carefully before using your new product. Do not install or
operate the product until you are familiar with all operating instructions and warnings. Do not allow
anyone else to operate the product until they are familiar with all operating instructions and warnings.
⚠WARNING California Proposition 65. This product can expose you to chemicals including
styrene and vinyl chloride which are on the list of over 900 chemicals identified by
the State of California to cause cancer, birth defects or reproductive harm. Always
use this product in accordance with BendPak’s instructions. For more information,
visit www.p65warnings.ca.gov.
Important Safety Information
When using this equipment, basic safety precautions should always be followed, including:
•Read all instructions. Use only as described in this manual.
•Only operate your Lift between temperatures of 41°F to 104°F (5°C to 40°C).
•Make sure all operators read and understand this Installation and Operation Manual.
Keep the
manual near the Lift at all times
. The Lift should only be operated by authorized personnel.
Keep children and untrained personnel away from the Lift.
•BendPak recommends referring to the ANSI/ALI ALIS Standard Safety Requirements for
Installation and Service for more information about safely installing, using, and servicing your Lift.
•The Lift should only be operated by authorized personnel. Keep children and untrained personnel
away from the Lift.
•Do not make any modifications to the Lift; this voids the warranty and increases the chances of
injury or property damage. Use only factory-approved attachments.
•Do not use the Lift while tired or under the influence of drugs, alcohol, or medication.
•Do not touch hot parts; you could be burned. Always use care with the equipment.

10AP Series Two-Post Lifts 6P/N 5900265 — Rev. A6 — December 2022
•Do not operate equipment with a damaged cord or if the equipment has been dropped or
damaged – until it has been examined by a qualified service person.
•Do not let a cord hang over the edge of a table, bench, or counter or come in contact with hot
manifolds or moving fan blades. Loop the power cord around equipment when storing.
•If an extension cord is necessary, a cord with a current rating equal to or greater than that of the
equipment should be used. Cords rated for less current than the equipment may overheat. Care
should be taken to arrange the cord so that it will not be tripped over or pulled out.
•Always unplug equipment from electrical outlets when not in use. Never use the cord to pull the
plug from the outlet. Grasp plug and pull to disconnect.
•To reduce the risk of a fire, do not operate equipment in the vicinity of open containers of
flammable liquids (like gasoline).
•Adequate ventilation should be provided when working on operating internal combustion engines.
•Keep hair, loose clothing, fingers, and all parts of the body away from moving parts.
•To reduce the risk of electric shock, do not use the unit on wet surfaces or expose to rain.
•Always wear safety glasses! Everyday glasses only have impact resistant lenses, they are not
safety glasses.
Save these instructions!
Additional Safety Information
The following safety information applies to all BendPak 10AP models:
•10AP Series Lifts are Two Post Service Lifts.
Use them only for their intended purpose.
•You must wear OSHA-approved (publication 3151) personal protective equipment
at all times
when installing, using, maintaining, or repairing the Lift. Leather gloves, steel-toed work boots, eye
protection, back belts, and hearing protection are
mandatory .
•
Never exceed the rated capacity of the Lift.
•When the Lift is in use, keep hands and all body parts well away from it.
•Keep loads balanced on the Lift Arm Assemblies. Clear the area immediately if a Vehicle is in
danger of falling off the Lift.
•Modifications void the warranty and increases the chances of injury or property damage.
Do not
modify any safety-related features in any way
.
•The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make sure to
implement them after connecting the Lift to a power source.
•When handling the Hydraulic components,
always wear safety gloves! In rare cases, a
needle-like stream of Hydraulic Fluid (even at low pressure) can penetrate fingers, hands, or arms.
Such a puncture can feel like a bite, electric shock, or a prick. While it may seem like a minor issue,
any amount of Hydraulic Fluid injected into the human body is a serious issue. Anyone suffering
such a puncture wound should be
immediately taken as an emergency to the hospital to
determine the extent of the injury. Explain the circumstances of the injury to the attending
physician, including what type of Hydraulic Fluid was involved. Do not assume a puncture wound
that could have been caused by Hydraulic Fluid is a minor issue; it could be life-threatening.
•Make a visual inspection of the Lift before using it. Do not use the Lift if you find any missing or
damaged parts. Instead, take it out of service, then contact an authorized repair facility, your
distributor, or BendPak at [phone] or email [e-mail].
•BendPak recommends making a
thorough inspection of the Lift at least once a year. Replace
any damaged or severely worn parts, decals, or warning labels.

10AP Series Two-Post Lifts 7P/N 5900265 — Rev. A6 — December 2022
Symbols
Following are the symbols used in this manual:
⚠DANGER Calls attention to a hazard that will result in death or injury.
⚠WARNING Calls attention to a hazard or unsafe practice that could result in death or injury.
⚠CAUTION Calls attention to a hazard or unsafe practice that could result in personal injury,
product damage, or property damage.
NOTICE Calls attention to a situation that could result in product or property damage.
Liability Information
BendPak assumes no liability for damages resulting from:
• Use of the equipment for purposes other than those described in this manual.
• Modifications to the equipment without prior, written permission from BendPak.
• Injury or death caused by modifying, disabling, overriding, or removing safety features.
• Damage to the equipment from external influences.
• Incorrect operation of the equipment.

10AP Series Two-Post Lifts 8P/N 5900265 —Rev. A6 — December 2022
Components
Not all components shown. Models with extensions are taller.Reference only –do not scale.

10AP Series Two-Post Lifts 9P/N 5900265 —Rev. A6 — December 2022
Specifications
Reference only –do not scale.
Top View
Approach View

10AP Series Two-Post Lifts 10 P/N 5900265 — Rev. A6 — December 2022
Model 10AP 10AP-168 10APX 10APX-181
Lifting Capacity 10,000 lbs. / 4,536 kg
Max. Capacity — Front Axle 5,000 lbs. / 2,268 kg
Max. Capacity — Rear Axle 5,000 lbs. / 2,268 kg
A– Max. Rise 69 in. / 1,753 mm 75.5 in. / 1,918 mm
B– Lifting Height w/ Pad173 in. / 1,854 mm 79.5 in. / 2,007 mm
C– Max. Lifting Height182.5 in. / 2,095 mm 89 in. / 2,261 mm
D– Min. Height w/ Pad 4 in. / 102 mm
E– Overall Height 145 in. /
3,683 mm
168 in. /
4,267 mm
157 in. /
3,988 mm
181 in. /
4,597 mm
F– Width Overall (Narrow) 135 in. / 3,431 mm
F– Width Overall (Wide) 145 in. / 3,683 mm
G– Outside Posts (Narrow) 127.5 in. / 3,238 mm
G– Outside Posts (Wide) 137.5 in. / 3,492 mm
H– Inside Posts (Narrow) 108.5 in. / 2,756 mm
H– Inside Posts (Wide) 118.5 in. / 3,010 mm
I– Drive-Thru Width (Narrow) 92. in. / 2,338 mm
I– Drive-Thru Width (Wide) 102 in. 2,592 mm
J– Floor to Top Switch 140 in. /
3,556 mm
163 in. /
4,140 mm
152 in. /
3,861 mm
176 in. /
4,470 mm
K– Front Arm Reach (min) 24.5 in. / 622 mm
K– Front Arm Reach (max) 50 in. / 1,270 mm
L– Rear Arm Reach (min) 32 in. / 812 mm
L– Rear Arm Reach (max) 59.25 in. / 1,504 mm
Max. load per Lift Arm 2,500 lbs. / 1,134 kg
Screw Pad Adjustment 2 in. / 51 mm
Time to Full Rise ≈45 seconds
Motor2220 VAC, 60 Hz, 1 Phase
Sound <70 dB
1Lifting Height w/Pad is maximum lifting height with Pads adjusted to the lowest setting and no adapter(s). Maximum Lifting
Height is maximum lifting height with Pads adjusted to high setting and with both tall and medium Adapters installed.
2Special voltages available upon request.
3Lift Arms measured from the pivot center to the end of the Lift Arm.
Specifications subject to change without notice.

10AP Series Two-Post Lifts 11 P/N 5900265 — Rev. A6 — December 2022
Installation Checklist
Following are the steps needed to install a 10AP Series Two-Post Lift; perform them in this order.
☐1. Review the Safety Rules.
☐2. Make sure you have the necessary tools.
☐3. Plan for Electrical Work.
☐4. Review the Installation Orientation.
☐5. Review Clearances around the Lift.
☐6. Select the Installation Location.
☐7. Choose a Wide or Narrow Configuration (
do not proceed until you have chosen ).
☐8. Install the Safety Assemblies and position the Safety Cable.
☐9. Put Equalizing Cables into position.
☐10. Add Extension Pieces (10AP-168 or 10AP-181 Models only).
☐11. Learn about Hydraulic Fluid contamination.
☐12. Learn about Liquid Thread Sealant.
☐13. Routing the Hydraulic Hoses.
☐14. Create Chalk Line Guides for the Posts.
☐15. Anchor the Posts.
☐16. Prepare and install the Overhead Assembly and Safety Shutoff Bar.
☐17. Install the Microswitch.
☐18. Install the Equalizing Cables.
☐19. Mount the Power Unit (but do not connect it to power yet).
☐20. Route and install the Safety Lock Cable.
☐21. Connect the Hydraulic Hoses.
☐22. Install the Lift Arm Assemblies.
☐23. Perform final Leveling.
☐24. Contact the Electrician.
☐25. Wire the Microswitch (
Electrician required ).
☐26. Connect the Power Unit (
Electrician required ).
☐27. Install the Power Disconnect Switch and Thermal Disconnect Switch (
Electrician required ).
☐28. Lubricate the Lift.
☐29. Perform an Operational Test.
☐30. Review the Final Checklist.
☐31. Leave the Manual at the Lift for the Owner/Operator.

10AP Series Two-Post Lifts 12 P/N 5900265 — Rev. A6 — December 2022
Installation
The installation process includes multiple steps. Perform them in the order listed.
⚠WARNING Use only the factory-supplied parts shipped with your Lift. If you use attachments,
accessories, or configuration modifying components that are in the path and/or
affect the operation of the equipment, affect the equipment’s electrical listing, or
affect the intended Vehicle accommodation, and if they are not certified for use
with this Lift, then you void the warranty of the Lift as well as compromising the
safety of everyone who sets up or uses the Lift. If you are missing parts, visit
BendPak.com/Support, email [e-mail] or contact BendPak
Technical Support at [phone].
Reviewing the Safety Rules
When installing a Lift, your safety depends on proper training and thoughtful operation. BendPak
recommends referring to the ANSI/ALI ALIS Standard Safety Requirements for Installation and Service
for more information about safely installing, using, and servicing your Lift.
⚠WARNING Do not install this equipment unless you have automotive lift installation training.
Always use proper lifting tools, such as a Forklift or Shop Crane, to raise heavy
components. Do not install this equipment without reading and understanding this
Manual and the Labels on the unit.
Only fully trained personnel should be involved in installing this equipment. Always pay attention. Use
appropriate tools and lifting equipment. Stay clear of moving parts.
⚠WARNING You must always wear appropriate protective equipment during installation: leather
gloves, steel-toed work boots, eye protection, back belts, and hearing protection.
Gathering Your Tools
You may need some or all of the following tools:
•
Rotary hammer drill (or similar)
•
3/4-inch carbide bit (conforming to ANSI
B212.15)
•
Hammer
•
Four-foot level
•
Open-end wrench set, SAE, and metric
•
Socket and ratchet set, SAE, and metric
•
Hex-key wrench set
•
Crescent and pipe wrenches
•Crowbar
•Chalk line
•Medium-sized flat screwdriver
•Tape measure, 25 feet or more
•Needle-nose pliers
•Forklift or Shop Crane
•Two 12-foot ladders
•Two sawhorses
•Torque wrench

10AP Series Two-Post Lifts 13 P/N 5900265 — Rev. A6 — December 2022
Preparing for Electrical Work
You will need to have a licensed, certified Electrician available at some point during the installation.
⚠DANGER All wiring must be performed by a licensed, certified Electrician in accordance with
applicable local, state, and federal electrical codes, rules, and regulations, such as
state and federal OSHA regulations and electrical codes.
NOTICE Notify your Electrician in advance so they come prepared with the items required to
connect to the facility’s power system, or an appropriate power cord with plug to
connect to an appropriate VAC power source, a Power Disconnect Switch, and a
Thermal Disconnect Switch.
These items are not supplied with the Lift .
The Electrician needs to:
•Connect to the VAC power source. The Power Unit comes with a pigtail for wiring to a
power source. Have your Electrician connect a power cord with plug to the electrical box on the
Lift for connection to a power outlet or have them wire it directly into the electrical system at the Lift
location. The Lift’s Power Unit must be protected by an appropriate circuit breaker.
•Connect the Microswitch wiring to the Power Unit. The Microswitch must be wired to
the Power Unit. The required wiring is included with the Lift.
•Install a Power Disconnect Switch. A Power Disconnect Switch is used to shut down the
Lift in the event of an electrical circuit fault, emergency, or when the Lift is being serviced. Refer to
Installing a Power Disconnect Switch for more information.
•Install a Thermal Disconnect Switch. A Thermal Disconnect Switch automatically shuts
down the equipment in the event of an overload or an overheated motor. Refer to Installing a
Thermal Disconnect Switch for more information.

10AP Series Two-Post Lifts 14 P/N 5900265 —Rev. A6 — December 2022
Reviewing the Installation Orientation
Keep these factors in mind when deciding how to orient the Lift:
•The first thing to figure out is which direction you will be driving the Vehicles in, called the
Approach.
oIn most cases, this is simple: there’s a driveway on one side and a wall on the other side.
The driveway is your Approach. This makes the wall side the Front of the Lift and the
driveway side the Rear of the Lift.
oIf both sides are open, decide which way you will be driving Vehicles onto the Lift. This is
the Approach; the drive-on side is the Rear of the Lift and the drive-off side if the Front.
•
The Power Unit must be installed on the Powerside Post . You can identify the
Powerside Post by the Mounting Bracket to which the Power Unit attaches; only one Post that
came with your Lift has a Mounting Bracket.
The following illustration shows the Power Unit location for your Lift.
Reference only –do not scale.
Top View

10AP Series Two-Post Lifts 15 P/N 5900265 —Rev. A6 — December 2022
Checking Clearances
Clearance around and above the Lift is required for safety .Refer to the figures below.
Figuresare not to scale. Not all components shown. Additional distance may be required on the Front
and Rear to allow Vehicles to be driven in or out from these directions.

10AP Series Two-Post Lifts 16 P/N 5900265 — Rev. A6 — December 2022
Selecting a Location
When selecting the location for your Lift, consider the following:
•Architectural plans. Consult the architectural plans for the desired location. Make sure there
are no contradictions between what you want to do and what the plans show.
•Available space. Make sure there is enough space for the Lift: front, back, sides, and
above .
Refer to Specifications for exact measurements. Check for overhead obstructions such as
building supports, heaters, lights, electrical lines, low ceilings, and so on.
•Power. You need an appropriate VAC power source for the Lift’s Power Unit.
•Outdoor installations.10AP Series Two-Post Lifts are approved for indoor installation and use
only.
Outdoor installation is prohibited.
•Floor. Only install the Lift on a flat, concrete floor; do not install on asphalt or any other surface.
The surface must be level; do not install if the surface has more than 3° slope.
⚠WARNING Installing your Lift on a surface with more than three degrees of slope could lead to
injury or even death. Only install your Lift on a level floor (defined as no more than
3/8 of an inch difference over the installation area). If your floor is not level, consider
making the floor level or using a different location.
•Concrete specifications. The concrete must be a minimum 4.25 inches thick, 3,000 PSI
minimum compressive strength, and cured for a minimum of 28 days. Do not install the Lift on
cracked or defective concrete. Anchor Bolts must be more than 6 inches from cracks and
expansion joints in the concrete or from a wall.
⚠CAUTION BendPak Lifts are supplied with installation instructions and concrete anchors that
meet the criteria set by the latest version of the American National Standard in
Automotive Lifts – Safety Requirements for Construction, Testing, and Validation in.,
ANSI/ALI ALCTV. Consult with an expert for any special regional structural and/or
seismic anchoring requirements specified by any other agencies and/or codes such
as the Uniform Building Code (UBC) and/or International Building Code (IBC).
Check your floor for the possibility of it being a post-tension slab. In this case, contact the building
architect
before drilling. Using ground penetrating radar may help you find tensioned steel.
⚠WARNING Cutting through a tensioned cable can result in injury or death. Do not drill into a
post-tension slab unless the building architect confirms you are
not going to hit
tensioned steel, or you have located it using ground penetrating radar.
If colored
sheath comes up during drilling, stop drilling immediately
.
•Unloading the components. Unload the Lift components as close to the installation location
as possible. The Lift includes several heavy pieces, so the closer you unload them to the
installation location, the better off you will be.
⚠WARNING Some Lift components are very heavy; if handled incorrectly, they can damage
materials like tile, sandstone, and brick. Try to handle the Lift components just
twice: once when delivered and once when moved into position. You must have a
Forklift or Shop Crane to move some of the Lift components into position.
Use
care when moving Lift components
.

10AP Series Two-Post Lifts 17 P/N 5900265 —Rev. A6 — December 2022
Choosing a Wide or Narrow Configuration
10AP Series Two-Post Liftscan be installed in a Wide or Narrow Configuration:
•Wide Configuration. The Posts are farther apart, which means you can raise wider Vehicles on
the Lift. This is usually the best choice
if your Lift location is wide enough to support it. When
installing the Equalizing Cables, use the Button End at the very end of the cable.
The following drawing shows an Equalizing Cable; the ends are exaggerated for clarity.
•Narrow Configuration. The Posts are closer together. This is usually the best choice for
narrower garages, as it uses less width. When you are installing the Equalizing Cables, use the
Button End
away from the end of the cable.
NOTICE 10AP Series Lifts are shipped from the factory with the Overhead Assembly and the
Safety Shutoff Bar already configured in the Narrow Configuration.Refer to Installing
the Overhead Assembly and Safety Shutoff Bar for information about
switching to the Wide Configuration.
You do not need to do anything to the Overhead Assembly at this point, but you must
decide on a
Wide or Narrow Configuration
now for two reasons:
•Routing the Equalizing Cables. The Equalizing Cables come with two Button ends, one for
the Wide Configuration and one for the Narrow Configuration. You need to know which Button end
to use when you put the Equalizing Cables into position.
•Creating the Chalk Line Guides. You use the Overall Width setting (in Specifications) to
create the Chalk Line Guides, so you know how far apart to put your Posts. There are two Width
Overall settings, one for the Wide Configuration and one for the Narrow Configuration. You need to
know which one to use when you are creating your Chalk Line Guides.
NOTICE If you are installing a Lift and do not yet know if it is going to be a Wide or a Narrow
Configuration, you need to
figure it out now , before you go any further in the
installation process.

10AP Series Two-Post Lifts 18 P/N 5900265 —Rev. A6 — December 2022
Installing the Safety Assemblies and Positioning the Safety
Lock Cable
Leaving both Lift Posts flat on the ground with access to the inside of the Post will ease the Safety
Lock installation and threading of the Safety Lock Cable into position. This procedure is intended to
leave the cable coiled at the top of the Offside Post, ready for routing after the Posts are standing. This
position will also make it easier to put the Equalizing Cables into position.
10AP Series Lifts have two Safety Assemblies: one on the Powerside Post (above the Power Unit) and
the other on the Offside Post at the same height.
The two Safety Assemblies engage the Lift head and prevent it from lowering. The Safety Release
mechanism allows the Lift Head to move past the Safety Locks and lower to the ground. The Safety
Assemblies must be disengaged
at the same time so that both Lift Heads lower together. To
accomplish this, the two Safety Assemblies are connected to each other via a Safety Lock Cable,
which is routed through the Lift Posts and the Overhead Assembly.
The following illustrations display the Offside and Powerside Safety Mechanisms.
Offside Safety: Similar to the Powerside
Safety, except that it does not have a Safety Lock
Release Handle.
Powerside Safety: The Powerside Safety
includes a Safety Lock Release Handle and
spring, which is pushed down and used to
disengage the Safety Locks when lowering the
Lift.
Not to scale. Components removed for clarity.

10AP Series Two-Post Lifts 19 P/N 5900265 —Rev. A6 — December 2022
To assemble and install the two Safety Assemblies and pre-position the safety
release cable:
Put both Posts either flat on the ground or elevated on a sawhorse or similar. The insides of the
Posts must be accessible, facing up.
Slide the Lift Heads away from the bottom of both Posts. Far enough to clear the Latch Support
Plate and provide room to work.
Illustration above is a top view looking at the inside of the Lift Post. Not to Scale. Some
components removed for clarity.
Begin on the Offside Post , retrieve the Offside Safety Block (5737177), two extension springs
(5540047), four M6 x 20 machine screws (5530065) and the Pivot Pin (5746494) from the Parts
Bag. Overlap the Safety Block over the Latch Support Plate welded to the Offside Lift Post. Then
attach the extension Springs. Overlapping these parts will ease the Extension Spring installation.
Then move the Safety Block to overlap the Latch Support Plate and secure using the Safety Pivot
Pin as shown below.
Not to scale. Components removed for clarity.

10AP Series Two-Post Lifts 20 P/N 5900265 —Rev. A6 — December 2022
Reference only –do not scale.
Locate the Safety Lock Cable. This is a long, thin Wire Rope Cable with a Button swaged onto one
end and nothing on the other end. Thread the cable through the Offside Safety Block as shown
above. Part Number and Cable length varies based on Lift Model.
Model Part Number Safety Cable
Dia. and Length
10AP 5595793 Ø1.8 x 7,773 mm
10AP-168 5595831 Ø1.8 x 8,865 mm
10APX 5595832 Ø1.8 x 8,103 mm
10AP-181 5595833 Ø1.8 x 9,322 mm
Thread the remainder of the Safety Lock Cable under the Safety Cable Sheave and Lift Head, then
up to the top of the Offside Post.
Coil the cable and secure with tape or a Zip Tie at
the top of the Offside Lift Post until called for later in the assembly.