Bennett BOLT Rocker BRC4000 User manual

User Quick-start Guide
BCN Control Installation Instructions
Refer to the wiring diagram (reverse side) and installation
template (below).
• Before drilling any holes, read the entire instructions.
• Using the included template (below), mark the locations for
the 7/64" holes and the 2.5" center hole.
• Check carefully ensure there are no obstructions behind the
console before drilling.
• Using a 2.5" diameter hole-saw, drill the center hole. Use a
7/64" drill for the four mounting stud holes.
• Unsnap the bezel from the control plate.
• Remove the four (4) #8 screws from the hardware bag and
insert into the holes on each corner of the control plate.
• Place the control plate onto the console, feeding the pre-
connected wires through the 2.5" center hole while inserting
the screws into each of the four holes.
• Once the control plate is properly seated, screw down the
four (4) #8 screws (do not over-tighten) and snap the bezel
back onto the plate assembly.
• e port cable on the rocker switch is marked with a red
band. e starboard cable on the rocker switch is marked
with a green band. Note: After the actuators are installed, the
port cable (red band) will be connected to the wire harness
coming from the port actuator, conversely the starboard cable
(green band) will be connected to the wire harness coming
from the starboard actuator.
• Plug the port yellow/blue 20ft. twisted cable
(PN# BAW20XX) to the port connector on the BRC Rocker
Control.
• Plug the starboard yellow/blue 20ft. twisted cable
(PN# BAW20XX) to the starboard connector on the BRC
Rocker Control.
• Connect the orange wire from the rocker switch to (+) 12V
(20A) power and black wire to ground.
BOLT Rocker Control (BRC4000) Installation & Quick-start Instructions
For information on installing a complete BOLT Trim Tab System, please visit BennettTrimTabs.com/BOLT-Install
Lowers
Port Bow
Raises
Port Bow
Lowers
Starboard
Bow
Raises
Starboard
Bow
BRC Control Installation Templates
Both control templates below are identical. e second has been provided for dual station applications. Must be copied at 100% if replicated.
Must be printed/copied at 100% scale 1"
1
—
8
2
2
"
2
"
1
—
8
2
"
13
—
16 13
—
16
2
"
1
—
2
"
7
—
64
BRC Rocker Templates
Both templates on this page are identical. The second has been provided for dual station applications.
"
1
—
8
2
2
"
2
"
1
—
8
2
"
13
—
16 13
—
16
2
"
1
—
2
"
7
—
64
"
Verify template dimensions if
printed from the web or copied
Verify template dimensions if
printed from the web or copied

Have questions?
We’re here to help. Call us at [phone] for assistance.
BOLT Trim Tab System Wiring Diagram with BRC Control
For information on installing a complete BOLT Trim Tab System, please visit BennettTrimTabs.com/BOLT-Install
BQE121 r031406
ORANGE WIRE
CONNECT TO
20A,(12V)
10A, (24V)
GROUND
2
1
3
No.
Part Name
Spec Sheet
1
BQEACT-X
BQE
2
BQEMTREXTCABLE-X
Wire Harness
3 ES-1000 RS
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Bennett Marine Inc. ANY REPRODUCTION
IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSION OF
Bennett Marine Inc IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
NEXT ASSY
USED ON
APPLICATION
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
1/16
ANGULAR: MACH
BEND
TWO PLACE DECIMAL .01
THREE PLACE DECIMAL
.005
INTERPRET GEOMETRIC
TOLERANCING PER: ANSI Y-14
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DATE
NAME
TITLE:
SIZE
B
DWG. NO.
REV
WEIGHT:
SCALE: 1:8
UNLESS OTHERWISE SPECIFIED:
SHEET 5 OF 5
BQE-0-0-1
DO NOT SCALE DRAWING
Bennett Marine
550 Jim Moran Blvd
Deerfield Beach, FL 33442
1. Actuators
2. Display Extension Cable
3. Helm Display
For dual station or dual actuator wiring
diagrams please visit
BennettTrimTabs.com/BOLT-Install