Beckhoff CP29 -2 -0000 Series User manual

Manual | EN
CP29xx-2xxx-0000
Control Panel
4/8/2021 | Version: 1.2

Table of contents
CP29xx-2xxx-0000 3Version: 1.2
Table of contents
1 Notes on the documentation ....................................................................................................................5
2 For your safety...........................................................................................................................................6
2.1 Description of safety symbols............................................................................................................6
2.2 Intended use......................................................................................................................................6
2.3 Fundamental safety instructions........................................................................................................7
2.4 Operator's obligation to exercise diligence ........................................................................................7
3 Product overview.......................................................................................................................................8
3.1 Structure ............................................................................................................................................9
3.2 Interface description ........................................................................................................................10
3.2.1 Power supply ................................................................................................................... 10
3.2.2 USB ................................................................................................................................. 11
3.2.3 DVI................................................................................................................................... 11
3.3 Name plate ......................................................................................................................................12
3.4 Connection cables/connection kits ..................................................................................................13
4 Commissioning........................................................................................................................................14
4.1 Transport and storage .....................................................................................................................14
4.2 Installation in the control cabinet .....................................................................................................15
4.2.1 Dimensions ...................................................................................................................... 15
4.2.2 C6030 installation ............................................................................................................ 17
4.2.3 Installation in the control cabinet ..................................................................................... 18
4.3 Connecting the Control Panel..........................................................................................................19
4.3.1 Installing the supply cable................................................................................................ 19
4.3.2 Grounding the Control Panel ........................................................................................... 21
4.3.3 Connecting cables and power supply .............................................................................. 22
5 Shutting down..........................................................................................................................................23
5.1 Disconnecting the power supply and cables ...................................................................................23
5.2 Disassembly and disposal ...............................................................................................................24
6 Servicing and maintenance ....................................................................................................................25
7 Troubleshooting ......................................................................................................................................26
8 Technical Data .........................................................................................................................................27
9 Appendix ..................................................................................................................................................28
9.1 Service and support.........................................................................................................................28
9.2 Approvals.........................................................................................................................................29

Table of contents
CP29xx-2xxx-00004 Version: 1.2

Notes on the documentation
CP29xx-2xxx-0000 5Version: 1.2
1 Notes on the documentation
This description is only intended for the use of trained specialists in control and automation engineering who
are familiar with the applicable national standards.
The following instructions and explanations must be followed during installation and commissioning of the
components. The qualified personnel must ensure that the application of the described products meets all
safety requirements, including all applicable laws, specifications, regulations and standards.
Disclaimer
The documentation has been prepared with care. The products described are, however, constantly under
development. For that reason the documentation is not in every case checked for consistency with
performance data, standards or other characteristics. In the event that it contains technical or editorial errors,
we retain the right to make alterations at any time and without warning. No claims for the modification of
products that have already been supplied may be made on the basis of the data, diagrams, and descriptions
in this documentation. All illustrations shown are only examples. The configurations depicted may deviate
from the standard.
Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, EtherCAT P®, Safety over EtherCAT®, TwinSAFE®, XFC® and XTS®
are registered and licensed brands of Beckhoff Automation GmbH. Other designations used in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights of
the owners.
Patents
The EtherCAT Technology is covered, including but not limited to the following patent applications and
patents: EP1590927, EP1789857, DE102004044764, DE102007017835 with the corresponding applications
and registrations in various other countries. The TwinCAT Technology is covered, including but not limited to
the following patent applications and patents: EP0851348, US6167425 with corresponding applications or
registrations in various other countries.
Copyright
© Beckhoff Automation GmbH & Co. KG. Publication of this document on websites other than ours is
prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the
grant of a patent, utility model or design.
Delivery state
All the components are supplied in particular hardware and software configurations appropriate for the
application. Changes to the hardware or software configuration are permitted, provided they are within the
specified limits for power consumption and power dissipation (please refer to the respective data sheet).
Delivery conditions
In addition, the general delivery conditions of the company Beckhoff Automation GmbH & Co. KG apply.

For your safety
CP29xx-2xxx-00006 Version: 1.2
2 For your safety
The safety chapter explains the safety symbols used and their meanings. They contain fundamental safety
instructions that are essential for the avoidance of personal injuries and damage to property.
Exclusion of liability
Beckhoff shall not be liable in the event of non-compliance with this documentation and thus the use of the
devices outside the documented operating conditions.
2.1 Description of safety symbols
The following safety symbols are used in these operating instructions. In order to avoid personal injuries and
damage to property, read and follow the safety and warning notices.
Warning of personal injuries:
DANGER
Disregarding the safety notice will lead to death or serious injuries.
WARNING
Disregarding the safety notice may lead to death or serious injuries.
CAUTION
Disregarding the safety notice may lead to minor injuries.
Warning of damage to property:
NOTE
Disregarding the notice may lead to damage to property.
2.2 Intended use
The CP29xx multi-touch built-in Control Panel is designed for industrial applications in machine and plant
engineering. A multi-finger touch screen is installed in an aluminum housing. The Control Panel is installed in
the front of control cabinets. Standard cables allow the Control Panel to be placed up to 5 m away from the
PC.
The front of the Control Panel is designed for an IP65 working environment. It offers full protection against
contact and against water jets (nozzle) from any angle. The rear of the Control Panel is designed for an IP20
working environment. It is protected against the penetration of fingers and solid foreign bodies of 12.5 mm or
larger in size. It is not protected against water. The specified limits for technical data must be adhered to.
The Control Panel can be used within the documented operating conditions.
Improper use
Do not use the device outside the documented operating conditions.

For your safety
CP29xx-2xxx-0000 7Version: 1.2
2.3 Fundamental safety instructions
The following safety instructions must be observed when handling the device.
Application conditions
• Do not use the device under extreme environmental conditions. Protect the device against dust,
moisture and heat and keep the ventilation slits free.
• Never use the device in potentially explosive atmospheres.
• Do not carry out any work on the device while it is live. Always switch off the supply voltage for the
device before mounting it, replacing device components or rectifying malfunctions. This does not apply
to the replacement of hard disks in a RAID configuration.
• Never connect the device during a thunderstorm. There is a risk of electric shock.
Damage to property, loss of data and impairment of functions
• If you change the hardware and software configurations, you must keep within the specified limits of
power consumption and power dissipation (please refer to the respective data sheet).
• Ensure that only trained qualified persons with a control and automation technology background,
operate the device. Use by unauthorized persons can lead to damage to property and loss of data.
• Protect the power supply cable with a fuse with a max. rating of 16A. The fuse serves to protect the
supply line in the event of a short circuit.
• In case of fire, extinguish the device with powder or nitrogen.
2.4 Operator's obligation to exercise diligence
The operator must ensure that
• the products are used only for their intended purpose (see chapter 2.2 Intended use [}6]).
• the products are only operated in sound condition and in working order.
• the products are operated only by suitably qualified and authorized personnel.
• the personnel is instructed regularly about relevant occupational safety and environmental protection
aspects, and is familiar with the operating instructions and in particular the safety instructions contained
herein.
• the operating instructions are in good condition and complete, and always available for reference at the
location where the products are used.

Product overview
CP29xx-2xxx-00008 Version: 1.2
3 Product overview
The Beckhoff Panel generation with industrial multi-touch display is generally suitable for control cabinet
installation and for mounting arm installation, although only control cabinet installation is considered in this
documentation. The devices offer suitable solutions for a variety of applications. The wide model variety
ranges from different display sizes and formats to custom models. This Panel generation is also ideally
suited for single-touch applications.
The Control Panel has the following features:
• Different display sizes, landscape and portrait mode:
◦ 15.6 inch (16:9)
◦ 18.5 inch (16:9)
◦ 19 inch (5:4)
◦ 21.5 inch (16:9)
• Multi-finger touch screen (PCT): e.g., for 5-finger or 2-hand touch operation
• high touch-point density for safe operation
• Aluminum housing with glass front, front IP65, rear IP20
• 1x DVI
• 1x USB 3.0
• Control cabinet installation via pull-out clamping levers for fast installation without loose parts

Product overview
CP29xx-2xxx-0000 9Version: 1.2
3.1 Structure
Figure 1 shows an example of the device configuration for all CP29xx variants.
2
3
4
1
5
6
7
89
10
11
Fig.1: CP29xx_configuration
Table1: Legend for CP29xx configuration
No. Component Description
1 Touch Screen Operating the Control Panel
2 Clamping lever Mounting the Control Panel in the
control cabinet
3 Industrial PC C6030, optional Control system in machine
construction and plant engineering
4 Mounting plate for C6030 Part of the C6030: Plate for
mounting the Industrial PC at the
back of the Control Panel
5 Fastening points for C9900-K790 Attaching the power supply cable
adapter for shared use of CP29xx
and C6030
6 Connection block Access to the interfaces
7 Name plate Information on the Control Panel
equipment
8 Power supply (X101) Connection of the power supply
and external wiring of the Control
Panel
9 Grounding bolt Functional earthing of the Control
Panel
10 USB 3.0 interface (X104) Connection of peripheral devices
11 DVI interface (X106) Transmission of digital signals,
connection to digital displays

Product overview
CP29xx-2xxx-000010 Version: 1.2
3.2 Interface description
3.2.1 Power supply
The Control Panel is supplied with a nominal input voltage of 24 V. The five-pin power socket (X101) is used
for connection to the power supply and the external wiring of the Control Panel.
X101
1 2 345
Fig.2: CP29xx_voltage connector pin numbering
Table2: Voltage connector pin assignment
Pin Description Function
1 NC
2 NC
3
4 GND 0 V
5 24 V Power supply
The plug for the power supply is specified for 16A and can accommodate cable cross-sections of up to
1.5mm2. The plug is included in the delivery. Replacement plugs can be obtained from your Beckhoff service
contact (see Chapter 9.1, Service and Support).

Product overview
CP29xx-2xxx-0000 11Version: 1.2
3.2.2 USB
The Control Panel has a USB 3.0 interface (X104) that supports the USB 3.0 specification. The Control
Panel is connected to the Industrial PC via the USB input.
12
3
4
X104
Fig.3: CP29xx_USB interface pin numbering
Table3: USB interface pin assignment
Pin Connection Typical assignment
Shell Shield Drain Wire
1 VBUS Red
2 D - White
3 D + Green
4 GND Black
5 StdA_SSRX - Blue
6 StdA_SSRX + Yellow
7 GND_DRAIN N/A
8 StdA_SSTX - Purple
9 StdA_SSTX + Orange
3.2.3 DVI
The Control Panel has a DVI interface (X106). It is used to transmit the video signal from the Industrial PC to
the Control Panel.
The graphics signal is transmitted directly over a maximum distance of 5m. The Industrial PC requires a
conventional DVI output. The resolution at the Control Panel depends on the distance from the display
device.
1
9
17
8
16
24
X106
Fig.4: CP29xx_DVI interface pin numbering
Table4: DVI interface pin numbering
Pin Signal Pin Signal Pin Signal
1 Rx2- 9 Rx1- 17 Rx0-
2 Rx2+ 10 Rx1+ 18 Rx0+
3 GND 11 GND 19 GND
4 Rx4- 12 Rx3- 20 Rx5-
5 Rx4+ 13 Rx3+ 21 Rx5+
6 DDC CLK 14 + 5V DVI 22 GND
7 DDC DAT 15 GND 23 RxC+
8 AV SYNC 16 HPD 24 RxC-

Product overview
CP29xx-2xxx-000012 Version: 1.2
3.3 Name plate
1
2
3
4
5
6
7
8910 11
12
13
Fig.5: CP29xx_name plate
Table5: Legend for CP29xx name plate
No. Description
1 Model
2 FCC approval
3 Serial number (BTN)
4 Date of manufacture
5 Display
6 Touch screen
7 Power supply unit: 24 VDC, NEC class 2
8 DVI interface (X106)
9 USB interface (X104)
10 Grounding bolt
11 Connection of the power supply and external wiring
of the Industrial PC (X101)
12 CE conformity, EAC conformity
13 Address of the manufacturer

Product overview
CP29xx-2xxx-0000 13Version: 1.2
3.4 Connection cables/connection kits
The following connection cables and ready-made connection kits are available for the CP29xx-2xxx-0000:
Table6: Connection cables/kits CP29xx
Connection cables/connection kits Description
C9900-K774 Connection kit 1 m, includes: 1 m display port to DVI
cable, 1 m USB cable
C9900-K775 Connection kit 3 m, includes: 3 m display port to DVI
cable, 3 m USB cable
C9900-K776 Connection kit 5 m, includes: 5 m display port to DVI
cable, 5 m USB cable
C9900-K780 Display port connection cable for DVI-D display cable
1 m
C9900-K781 Display port connection cable for DVI-D display cable
3 m
C9900-K782 Display port connection cable for DVI-D display cable
5 m
C9900-K554 Connection cable USB-2.0 A-B, 1 m
C9900-K552 Connection cable USB-2.0 A-B, 3 m
C9900-K553 Connection cable USB-2.0 A-B, 5 m
Ready-made connection kits for DVI/USB connection are available as an option. They are included as
standard when you order the C6030 as an option for mounting at the back of the Control Panel. They can
also be ordered separately from Beckhoff sales, quoting the following article descriptions:
Table7: Connection kits CP29xx with C6030
Connection kit DVI/USB connection
C9900-K783 Display port connection cable for DVI-D display cable
0.33 m
C9900-K784 Connection cable USB-2.0 A-B, 0.37 m
C9900-K790 Power supply cable adapter for shared use of
C6030-2xxx-00x0 and CP29xx-2xxx-000

Commissioning
CP29xx-2xxx-000014 Version: 1.2
4 Commissioning
Operating the Control Panel
The Control Panel is operated via the touch screen.
NOTE
Damage to the touch screen
Operating the touch screen with unsuitable objects may damage it.
• Operate the touch screen only with your bare fingers, wearing special gloves or with a touch screen pen.
• If you use gloves, make sure that no hard particles such as metal shavings, glass splinters or similar ad-
here to the glove.
To use the Control Panel, you must first put it into operation. The first step is to transport the device to is
operating location and unpack it. This is followed by installing the device in the control cabinet, connecting
the cables and the power supply and finally switching on the Control Panel.
4.1 Transport and storage
The specified storage conditions must be adhered to (see chapter 8 Technical data).
Despite the robust design of the unit, the components are sensitive to strong vibrations and impacts. During
transport the device must therefore be protected from mechanical stress. Appropriate packaging of the Panel
PC, in particular the original packaging, can improve the vibration resistance during transport.
NOTE
Hardware damage due to condensation
Unfavorable weather conditions during transport can cause damage to the device.
• Protect the device against moisture (condensation) during transport in cold weather or in case of ex-
treme temperature fluctuations.
• Do not put the device into operation until it has slowly adjusted to the room temperature.
• Should condensation occur, wait for about 12 hours before switching the device on.
Unpacking
Proceed as follows to unpack the device:
1. Remove packaging.
2. Keep the packaging for possible future transport.
3. Check your delivery for completeness by comparing it with your order.
4. Check the contents for visible shipping damage.
5. In case of discrepancies between the package contents and the order, or in case of transport damage,
please inform Beckhoff Service (see chapter 9.1 Service and support [}28]).

Commissioning
CP29xx-2xxx-0000 15Version: 1.2
4.2 Installation in the control cabinet
The CP29xx Control Panel is designed for installation in control cabinets for machine and plant engineering
applications. Please observe the environmental conditions prescribed for the operation (see chapter 8
Technical Data).
The C6030 Industrial PC can optionally me mounted at the back of the Control Panel. If you choose this
option, you must first install the C6030 before you can mount the Control Panel in the control cabinet. You
will find the corresponding information in the following chapters.
4.2.1 Dimensions
The dimensions of the Control Panel are used to prepare the control cabinet and to ensure that the Panel is
correctly mounted in the control cabinet.
If you want to mount a C6030-200x-0060 at the back of the Control Panel, you can find the corresponding
dimensions in the C6030 device documentation.
All dimensions are in mm.
Fig. 6 shows the dimensions of the Control Panel with 15.6 inch display.
414
302
7,7
53,5
x
y
tcutout dimensions:
x=
y=
r=
t =
r
395
290
1,5 - 2,5
2
Fig.6: CP29xx_dimensions, 15.6 inch
Fig. 7 shows the dimensions of the Control Panel with 18.5 inch display.
498
341
51,5
7,7
x
y
tcut-out
dimensions:
x=
y=
r=
t =
r
465
319
1,5 - 2,5
2
Fig.7: CP29xx_dimensions, 18.5 inch
Fig. 8 shows the dimensions of the Control Panel with 19 inch display.

Commissioning
CP29xx-2xxx-000016 Version: 1.2
393
463
51,5
7,7
x
y
tcut-out
dimensions:
x=
y=
r=
t =
r
450
380
1,5 - 2,5
2
Fig.8: CP29xx_dimensions, 19 inch
Fig. 9 shows the dimensions of the Control Panel with 21.5 inch display.
559
377
7,7
51,5
x
y
tcut-out
dimensions:
x=
y=
r=
t =
r
542
362
1,5-2,5
2
Fig.9: CP29xx_dimensions, 21.5 inch

Commissioning
CP29xx-2xxx-0000 17Version: 1.2
4.2.2 C6030 installation
A C6030 can optionally be mounted at the back of the Control Panel. The following section contains the
information required for installing the Industrial PC.
The following two ordering options are available for the C6030 Industrial PC:
• C6030-2000-0060 (Smart Performance Class)
• C6030-2001-0060 (High Performance Class)
The housing of the Control Panel comes prepared with the mounting holes for the C6030. These are located
at the back of the device (see locations marked in Fig. 10).
Fig.10: CP29xx_without C6030
The holes are drilled in such a way that you can mount the C6030 on the panel using the mounting plate
over the side wall of the PC. Align the C6030 so that the fixing screws can be fitted at the marked points on
the mounting plate (see Fig. 11).
Fig.11: C6030_fixing screw positions
Place the C6030 over the holes on the panel and tighten the fastening screws (see Fig. 12).
Fig.12: CP29xx_assembly C6030

Commissioning
CP29xx-2xxx-000018 Version: 1.2
For more information about the C6030 Industrial PC please refer to the device documentation.
4.2.3 Installation in the control cabinet
Preparation of the control cabinet
The control cabinet must have the required installation cutout according to the device dimensions (see
Chapter 4.2.1 Dimensions [}15]) of the Control Panel.
NOTE
Extreme environmental conditions
Extreme environmental conditions can cause damage to the device.
• Avoid extreme environmental conditions.
• Protect the device against dust, moisture and heat.
• Do not block the ventilation slits of the device.
For installation in the control cabinet, make sure there is 5cm free space above and below the Control Panel
for air circulation.
Please also note the following for installation in a control cabinet:
• Place the Control Panel such that reflections on the screen are avoided as far as possible.
• For the correct installation height, use the position of the screen for guidance. This should always be
optimally visible to the user.
• Do not expose the Control Panel to direct sunlight.
• When the unit is in its mounting position, the ventilation openings must not be obstructed.
Installation in the control cabinet
Once you have made the required cutout in the control cabinet, you can install the Control Panel in the
control cabinet. Clamping levers are provided at the back of the housing for final mounting of the device.
To install and secure the Control Panel in the control cabinet, follow the steps shown in Fig. 13:
1. Insert the Control Panel at the intended position in the panel of the control cabinet. Make sure that the
device is secured against falling out until it is fastened properly.
2. Loosen the clamping levers with a 3.0 mm Allen key (sections A and B).
3. Fold the clamping levers 90° to the side (section C).
4. Retighten the clamping levers with the Allen key (section D).
A B
CD
Fig.13: CP29xx_control cabinet installation

Commissioning
CP29xx-2xxx-0000 19Version: 1.2
4.3 Connecting the Control Panel
CAUTION
Risk of electric shock
Dangerous touch voltages can lead to electric shock. To avoid electric shock, observe the following:
• Never connect or disconnect the device cables during a thunderstorm.
• Provide protective earthing for handling the device.
To prepare the Industrial PC for operation, it must be connected. The first step is to ground the device. Then
you can connect the cables and the power supply.
An external power supply unit is required to supply 24VDC (-15%/+20%) for operating the device.
Wire the Industrial PC in the control cabinet in accordance with the EN 60204-1:2006 standard on Protective
Extra Low Voltage (PELV) so that one side of the circuit or a point on the power source of this circuit is
connected to the protective conductor system.
Set "PE" and "0 V" (24 V power supply) to the same potential (connected in the control cabinet).
Connected devices that have their own power supply must have the same potential for "PE" and "GND" as
the Industrial PC system (no potential difference).
4.3.1 Installing the supply cable
Install the cable for the voltage supply of the Control Panel using the material supplied for connector
assembly. It consists of a 5-pin connection strip and a strain relief housing with cable tie.
Installing the supply cable
First mount the plug on the cable as follows:
1. Remove the insulation from the cable ends (8-9 mm).
2. Screw the cable ends into the 5-pin connection strip. For the pin assignment of the connector, see
Chapter 3.2.1 Power supply [}10].
Assembly of the strain relief housing
Now mount the strain relief housing on the previously connected plug and supply cable as shown in Fig. 14:
1. Thread the cable tie into the lower part of the strain relief housing (section A).
2. Insert the connection strip into the lower part of the strain relief housing (section B).
3. Tighten the cable tie and remove the plastic tab (section C).
4. Attach the upper part of the strain relief housing by snapping it onto the lower part (section D).

Commissioning
CP29xx-2xxx-000020 Version: 1.2
A B
CD
Fig.14: CP29xx_assembly of strain relief housing