Bernina HLT002 User manual

NOTE: LAY OUT ALL PARTS TO CONFIRM ALL ITEMS ARE AVAILABLE FOR ASSEMBLY.
SCREWS AND CONNECTORS
RIGHT DRAWER EXTENSION PLATFORM
1 PCS.
PAGE 1
#6 X 1 1/8" FH
8 PCS.
7/3/2019
TOOLS NEEDED TO ASSEMBLE!
NOT INCLUDED
#2 PHILLIPS SCREWDRIVER
LIFT TABLE EXTENSION KIT!
CONTENTS LIST
LEFT DRAWER EXTENSION PLATFORM
1 PCS.
STORAGE SHELF
1 PCS.
SHELF SIDE
2 PCS. SWIVEL CLAMP
2 PCS.
1/4 20 X 2" PH
TWIST CAM PIN
4 PCS.
6 PCS.

LIFT TABLE EXTENSION KIT!
ASSEMBLY INSTRUCTIONS
PAGE 2
FIGURE #1
NOTE: MAKE SURE ARROW POINT ON!
CAM LOCK IS POINTING UP TO ALLOW!
FOR PROPER ALIGNMENT ON TWIST CAM PINS
FIGURE #2-B
FIGURE #2
TABLE BOTTOM!
PANEL
TWIST CAM PIN
1. INSTALL TWIST CAM PINS
VIEW OF BACK OF TABLE
From back side of table locate!
6- 5mm holes on table bottom!
panel. Install 6- Twist Cam Pins!
using #2 Phillips Screwdriver as !
shown in Figure #1
2. INSTALL SHELF SIDES
Slide Shelf side onto Twist Cam Pins!
and with #2 Phillips Screwdriver turn!
twist cam clockwise until tight. !
Note: Make sure Twist Cams on !
Shelf Side are facing center of table!
as shown in Figure #2. If Shelf !
Side will not slide onto Twist!
cam pin refer to Figure #2-B!
below.
VIEW OF BACK OF TABLE
TWIST CAM
7/3/2019

LIFT TABLE EXTENSION KIT!
ASSEMBLY INSTRUCTIONS
PAGE 3
FIGURE #3
FIGURE #4
NOTE: IF BOLT WILL NOT THREAD INTO!
BARREL NUT, TURN NUT 1/2 TURN. (180º)
TYPICAL CONNECTOR!
JOINT
BARREL NUT
3. INSTALL SHELF
Position Shelf under Shelf Sides so
only 4 bolt holes can be seen from
bottom. Secure Shelf to Shelf Side
using 4- 1/4 20 X 2" PH bolts
with #2 Phillips Screwdriver as
shown in Figure #3. If bolt will not
thread in refer to Figure #3-B
VIEW OF BACK OF TABLE
FIGURE #3-B
SHELF SIDE
SHELF SIDE
1/4 20 X 2"PH!
BOLT
4. INSTALL SWIVEL CLAMPS
VIEW OF FRONT OF TABLE
DROP LEAF
DROP LEAFPRE-DRILLED!
HOLES
PRE-DRILLED!
HOLES
SWIVEL CLAMP
#6 X 1 1/8"FH SCREW
Locate 4-Pre-drilled Holes under!
each Drop Leaf. Install 1-Swivel!
Clamp with 4- #6 X 1 1/8"FH!
screws using #2 Phillips Screwdriver!
as shown in Figure #4. Refer to !
Figure #4-B for detail view.
FIGURE #4-B
7/3/2019

LIFT TABLE EXTENSION KIT!
ASSEMBLY INSTRUCTIONS
PAGE 4
FIGURE #5
FIGURE #6
5. PREPARE TO INSTALL LEFT AND RIGHT!
DDAWER EXTENSION PLATFORMS
Pull out both Left and Right !
Drawers as shown in !
Figure #5.
RIGHT DRAWER
LEFT DRAWER
6. INSTALLING LEFT AND RIGHT!
DRAWER EXTENSION PLATFORMS
Align pins on back edge of !
Left and Right Drawer !
Extension Platforms to Receiving!
Holes on Front Edge of Top.!
Lower Left and Right Drawer !
Extension Platforms onto !
drawer front while aligning !
pins to Receiving Holes on!
Top Edge of Drawer Front!
as shown in figure #6. The!
drawer extension platforms fit!
tightly into receiver holes. !
When installing use fingers to!
pull on drawer face and thumbs!
to push back and down on!
drawer extension platform!
until pins go into place. !
RECEIVING HOLES!
IN FRONT EDGE OF TOP
RECEIVING HOLES!
IN FROMNT EDGE !
OF TOP
RECEIVING HOLES ON!
TOP EDGE OF DRAWER!
FRONT
LEFT DRAWER!
EXTENSION PLATFORM
RIGHT DRAWER!
EXTENSION PLATFORM
VIEW OF FRONT OF TABLE
VIEW OF FRONT OF TABLE
7/3/2019

LIFT TABLE EXTENSION KIT!
ASSEMBLY INSTRUCTIONS
PAGE 5
FIGURE #7
FIGURE #8
7. CONNECT SWIVEL CLAMPS
Rotate Swivel Clamps !
clockwise until each one!
snaps into position as shown!
in Figure #7. This locks the!
Drop Leaf to the Left and!
Right Drawer Extension!
Platforms.
VIEW OF FRONT OF TABLE
DROP LEAF
DROP!
LEAF
LEFT DRAWER !
EXTENSION PLATFORM RIGHT DRAWER !
EXTENSION PLATFORM
SWIVEL !
CLAMP SWIVEL!
CLAMP
6. STORING LEFT AND RIGHT!
DRAWER EXTENSION PLATFORMS
LEFT DRAWER !
EXTENSION PLATFORM
RIGHT DRAWER !
EXTENSION PLATFORM
TOP VIEW
Lay Right Drawer Extension!
Platform upside down on flat!
surface. Lay Left Drawer !
Extension Platform right side!
up on top of Right Drawer!
Extension Platform as shown!
in Figure #8.
NOTE THAT VERTICAL ALIGNMENT PINs!
ARE CLEAR OF HITTING OPPOSITE PLATFORM.
7/3/2019