Bertin Technologies CORIOLIS COMPACT User manual

1 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Document reference: CORC-083-DU001-EN
Coriolis© is a registered trade mark of Bertin Technologies.
© 2021 Bertin Technologies. All rights reserved
Original instructions
CORIOLIS COMPACT
USER MANUAL

2 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
DISCLAIMER
Bertin Technologies and/or its subsidiaries accept no responsibility with respect to
the present document, whether explicit or implicit, in particular but not limited to
commercial warranties or individual warranties.
In the absence of legislation to the contrary, neither Bertin Technologies nor its
subsidiaries shall be held liable, either in contract or in tort, in terms of warranty or
any provision, for any damage arising in particular but not exclusively during the
use of this document.
Neither Bertin Technologies nor its employees shall be held responsible for losses or
costs arising from said use.
The information contained in the present document is intended solely for use with
this Bertin Technologies product. Bertin Technologies shall not be liable for any use
of this information in its application to other products.
Bertin Technologies reserves the right to revise the present document and make
periodic modifications without prior warning.
This liability disclaimer clause is governed by and interpreted in accordance with
French law. Any dispute arising from the content of said clause is therefore subject
to the exclusive jurisdiction of the Courts of Paris, France.
PROPRIETARY RIGHTS AND CONFIDENTIALITY
The information, research, drawings and diagrams contained in the present
document remain the property of Bertin Technologies and are confidential.
The information contained in the present document may not be used (whether in
part or in full), disclosed or reproduced without prior authorisation from Bertin
Technologies.

3 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Table of Contents
1Introduction............................................................................................................ 4
Safety instructions and recommendations ...................................................4
Technical assistance .........................................................................................7
Warranty..............................................................................................................7
2Equipment description.......................................................................................... 7
Operating principle.........................................................................................10
Specifications ...................................................................................................10
CE marking........................................................................................................11
3Transport/Storage ................................................................................................ 12
Transport............................................................................................................12
Storage ..............................................................................................................12
4Instructions for use when performing a collection........................................... 13
Installing the single-use assembly .................................................................13
Starting up the air sampler.............................................................................15
Self-testing.........................................................................................................16
Battery and mains power supply ..................................................................18
Starting/stopping collection ..........................................................................20
Suspending the collected sample in a solution .........................................25
5Settings ................................................................................................................. 27
6Cleaning and decontamination ........................................................................ 28
Cleaning............................................................................................................28
Decontamination ............................................................................................29
7Maintenance and servicing ............................................................................... 30
8Disposal ................................................................................................................ 30
9Appendix 1: EC Declaration of Conformity ...................................................... 31

4 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
1INTRODUCTION
Bertin Technologies is grateful that you have purchased the Coriolis Compact air
sampler.
The Coriolis Compact is an air sampler that has been designed specifically for
collecting micro-organisms through the implementation of cyclonic technology.
The Coriolis Compact is an innovative air sampler that assesses bio-contamination
levels. It is mainly designed to monitor and control air quality in environmental
research on pollution, in the pharmaceutical, food-processing and veterinary
industries and in the biomedical and health sectors.
This manual provides all of the required information for the installation, routine use,
maintenance and transport of your Coriolis Compact.
This document also summarises the operating mode for obtaining a sample with
the Coriolis Compact and for liquid suspension of the collected sample.
The user must read this manual carefully before using the Coriolis Compact air
sampler.
Contact the manufacturer immediately if there is any doubt relating to the safety
of this unit.
The technical specifications of this product and all information in this manual are
subject to change without prior warning.
Safety instructions and recommendations
This manual must be read carefully by any user before using the Coriolis Compact
air sampler.
Operating this unit without following the instructions provided in this manual may
impact the protection provided by this unit.
If you have any doubts or concerns regarding device safety, please contact us
via email at ai[email protected] or contact your local distributor.
You can find your local distributor on the Bertin Instruments website.

5 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Bertin Technologies shall not be held liable for any damage or injury that may arise
from the use of this device in any manner other than that indicated in the present
document.
Manufacturer address
Recommendations:
Do not remove the Coriolis Compact casing
Do not attempt to remove the battery from the Coriolis Compact unit (See §3.1)
Specific recommendations relating to the battery and charger:
Use only the charger supplied with the unit
Never charge the unit when close to flammable materials or products
Never dispose of the unit or battery on a fire and never subject them to high temperatures
The battery cells contain electrolytes, which may pose a risk to health. In the event of contact, rinse
well with cold water and seek medical assistance immediately.
Units containing a lithium battery must be stored with the battery charge being at least 30%. If it is
stored fully discharged, the integral battery will quickly become unusable and potentially
hazardous. It is recommended to check the battery’s state of charge every 6 months and to
recharge it as necessary.
BERTIN TECHNOLOGIES
Parc d’activités du Pas du Lac
10 bis, avenue Ampère - BP 284
78053 Saint-Quentin-en-Yvelines Cedex
FRANCE
Tel: [phone]
Email: [e-mail]

6 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
If you notice any damage to the unit or battery, do not recharge it. Contact your local distributor
or the manufacturer.
Never leave the unit in a location where the temperature could exceed 60°C.
1.1.1 Risk of electric shock
In order to avoid any risk of electric shock, the equipment’s power supply must be
connected to an installation that complies with the standards in force.
If the system does not start up, we ask that the operator contacts the
manufacturer.
It is essential that all users are aware of the potential risks associated with the use
of liquids near to an electrical power supply. If any liquid is spilled, the unit must be
disconnected immediately from its electrical power supply by pulling out the mains
plug, even if the unit is running. The unit must then be dried and the spilled liquid
wiped up.
1.1.2 Risk of explosion
The equipment is not ATEX-rated, so it must never be used in an explosive
atmosphere.
1.1.3 Risk of bio-contamination
Where applicable, gloves must be worn when handling the sample, in order to
avoid any risk of contamination of the sample by the user and vice-versa. Please
refer to the applications employed within your laboratory to ensure that the
laboratory best practices are applied.
1.1.4 Noise level
During normal operation, the device generates a noise level of 62 dB(A) (acoustic
pressure measurement obtained at a distance of 1 m from the unit’s surface).

7 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
1.1.5 Heavy-duty operation
Heavy-duty use of the system (sample collection >8 hours) may result in
components heating up and therefore premature system wear.
Technical assistance
Should a problem occur for which the solution is not listed in this manual, please
contact the manufacturer or your local distributor.
Warranty
BERTIN TECHNOLOGIES guarantees that the equipment is fault-free at the time of
shipping.
This warranty is limited to a one-year (1 year) period and does not cover the
batteries.
It is not applicable in the following scenarios:
•If the equipment has not been installed, handled or maintained in
accordance with the instructions provided in this manual.
•If the equipment has been opened, repaired or modified by unqualified
personnel.
•If the product serial number has been defaced or removed.
2EQUIPMENT DESCRIPTION
The Coriolis Compact is a dry-cyclone technology-based system for collecting
physical and biological particulates from the air. It is supplied in a carry case
containing:
The Coriolis Compact unit
A battery charger
1 pack of 10 single-use collection assemblies (cone + air intake)
1 pack of 10 collection cone caps
This instruction manual
The calibration certificate

8 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Figure 1: Coriolis Compact carry case
1
Carry case: includes a specific foam inlay for holding the unit’s various
components.
2
Charger: for charging the device’s battery.
3
Coriolis Compact: detailed view in Figure 2
4
Cones, caps and air intakes: supplied in packs of 10 single-use units

9 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Figure 2: Coriolis Compact description
1
Control panel: for powering the unit On/Off, operating controls and menu
navigation
2
Play/Pause button: for switching on the unit, starting a collection cycle,
pausing a collection cycle and confirming selections when navigating the
menu
3
Up/Down arrows: for menu navigation
4
Back button: for exiting the menu, stopping a collection
5
Carry strap clip (optional): for attaching a carry strap for transporting the
unit
6
Quick Connect Collar: for securing the air intake and the collection cone
7
Collection cone: for collecting micro-organisms (the cap is screwed at the
the end of the collection to preserve the sample)
8
Air intake: screws directly onto the collection cone, directs air flow into the
collection cone
9
Charger connector: for recharging the unit’s battery when it is plugged into
the mains power supply.

10 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Operating principle
During the collection process, airborne particulate matter in the ambient air is
aspirated into the collection cone via cyclonic action and pulled towards its walls.
Figure 3: Coriolis Compact operating principle
Stages
1. A sterile cone is placed onto the unit and locked into position
2. The aspirated air enters the cone
3. The airborne particles adhere to the cone wall
4. The collected particles are recovered by adding suspension liquid to the
cone
Specifications
Technical specifications
Power supply voltage
90 ->264 V AC @47-63 Hz
Energy consumption
36 W max.
Temperature cut-out
50°C (+- 5°C)
Electrical safety rating
Class 3
Dimensions
Coriolis Compact dimensions
255 x 135 x 130 mm
Carry case dimensions
464 x 366 x 176 mm

11 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Weight
Coriolis Compact weight
1.4 kg
Carry case weight when full
5.06 kg
Operating conditions
Use
Indoor and outdoor (IPX3)
Temperature
+5°C to +45°C
Temperature during charging
+0°C to +40°C
Humidity
10% - 90%
Mean flow rate
50 L/min
Figure 4: Summary table of Coriolis Compact main specifications
The battery charger is specifically for the unit. Do not use any other charger.
The batteries are of the Li-Ion type in compliance with subsection 38.3 of the UN
Manual of Tests and Criteria. Please refer to the current legislation applicable in
your country if necessary (see Section 3.1 TRANSPORT and §1.1 recommendations
relating to batteries)
CE marking
This equipment is compliant with the requirements of the CE marking and FCC Part
15 guidelines:
Figure 5: Example Coriolis Compact identification plate

12 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
3TRANSPORT/STORAGE
Transport
The Coriolis Compact unit must be transported in its carry case.
The equipment contains Li-Ion batteries, which are type-approved in accordance
with subsection 38.3 of the UN Manual of Tests and Criteria and have a low power
output (<100 Wh), so they are not classed as dangerous goods.
When in its carry case, the Coriolis Compact unit may be transported by road
without any specific restriction and by air either in the cabin or in the baggage
hold of a passenger aircraft.
When transporting the unit (with its battery), a label stating “UN3481: Lithium-Ion
batteries contained in or packed with the equipment” must be affixed to the
exterior packaging (see example below).
In all instances, please refer to the legislation in force in your country.
Storage
The unit must be kept in a dry location at a temperature of between +5°C and
+45°C.
The unit may be charged in a dry location at a temperature of between +0°C and
+40°C.
Please refer to Section 1.1 Safety instructions and recommendations, for details of
how to store the batteries.

13 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
4INSTRUCTIONS FOR USE WHEN PERFORMING A
COLLECTION
Installing the single-use assembly
1- Ensure that the lock is
in the open position on
the quick connect collar
2- Insert the top of the
cone into the
designated location
3- Lock the securing
collar by turning softly it
to the right (not more
180°) until you feel some
resistance
4- The secured padlock
symbol is visible on the
quick connect collar
and the cone is held in
place

14 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Handle the securing collar with precaution, you don’t need to force the
system.
Check that the quick connect collar is indeed in the locked position and that
the cone is located and secured correctly.
If it is not, unscrew the securing collar through one quarter of a turn to set it to the
correct position (the “open padlock” symbol is visible).
Insert the single-use assembly into the securing collar cradle.
Once the single-use assembly is placed correctly, set the collar to the closed
position to lock the assembly in position.
WARNING - IMPORTANT
Check that the single-use assembly is
positioned correctly

15 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Starting up the air sampler
Figure 1: Interface
1
Display screen: displays the menu, collection selections and unit settings
2
Play/Pause button: for switching on the unit, starting a collection cycle,
pausing a collection cycle and confirming selections when navigating the
menu.
2’
Device On/Off: press and hold to switch the unit on or off
3
Back button: for exiting the menu, stopping a collection
4
Up arrow button: for menu navigation
5
Down arrow button: for menu navigation
5’
Padlock: pressing and holding this button locks the keypad and prevents a
collection from being stopped unintentionally once started.

16 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Self-testing
The system performs self-testing during start-up.
If the self-test reveals no faults, the message “Autotest OK” will be displayed for 1
second, after which the main menu will appear.
If the self-test fails, the message “Autotests KO” followed by an error code will be
displayed until the operator confirms this.

17 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
The codes are as follows:
Code
Name
Meaning
Action
0x0002
LOGICIEL
Software error.
Restart the unit. If the
fault persists, return to
manufacturer
0x0004
BATLOW
Insufficient battery
voltage.
The unit saves the
current settings then
powers down. After
charging and restarting
the system, it will resume
operation in the state
that it was in when it
powered down.
Charge the battery.
If the fault persists, return
to manufacturer.
0x0008
BATHIGH
Battery overvoltage
Return to the
manufacturer.
0x0010
DEFCHARGE
Charger fault
Return to the
manufacturer.
0x0040
MOTNOTOK
Turbine state reading
KO
Return to the
manufacturer.
0x0100
BLUETOOTH
Communication with
Bluetooth module KO
Return to the
manufacturer.
0x0200
GPS
Communication with
GPS module KO
Return to the
manufacturer.
0x0400
SDCARD
SD card corrupt or full
Return to the
manufacturer.
0x0800
HORLOGE
The date and time have
not been specified by
the user.
Set the date and time via
the HMI. If the fault
persists, return to
manufacturer.

18 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Battery and mains power supply
The Coriolis Compact unit may be battery-operated or run on a main power
supply.
1
Battery charge: indicates the battery charge level
3 bars = battery charge > 75%
2 bars = battery charge > 50%
1 bar = battery charge > 25%
Indicator empty and flashing = battery discharged (< 25%)
Indicator with lightning bolt = battery charging
The battery life when in operation is approximately 8 hours.
If the battery charge level is not sufficient for the duration or number of collections
to be performed, connect the charger to the equipment via the jack socket then
connect the charger to the mains power supply.
Samples may be taken while the battery is charging (unit plugged into the main
power).
1

19 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Figure 2: Charging
1
Jack socket: For charging the Coriolis Compact
2
Charger: Coriolis Compact charger

20 WWW.BERTIN-INSTRUMENTS.FR
USER MANUAL
Starting/stopping collection
Once the device has been started up and the single-use assembly installed
correctly, use the arrows to navigate the main menu and select collection mode,
then confirm with the “PLAY” button.
The “RESET” button returns you to the previous menu. Pressing and holding the
down arrow locks or unlocks the keypad, to prevent unintentional operations
during the collection (unintentionally stopping the collection process, etc.).
Figure 9: Collection mode
1
Immediate collection: Starts collection without programming, stops at user
request.
2
Simple collection: Starts a collection delayed by an interval T1 and stops
after a programmed period T2.
3
Advanced collection: Starts a collection delayed by an interval T1, stops
after a programmed period T2 and then restarts after a timed delay T3,
performed over N cycles (T1+T2).
Note: For the immediate sampling, the screen continuously displays the time
elapsed from the start of the collection throughout the entire collection process
For the simple and advanced program it displays the time remaining since the start
of the collection process.