Better Bathrooms Arissa ARIMB008 User manual

Product
ARIMB008 - Arissa Matt Black Deck Mounted Shower Mixer Tap - 4 Tap
Hole
ARIBB008 - Arissa Brushed Brass Deck Mounted Shower Mixer Tap - 4 Tap
Hole
ARI H006 - Arissa hrome Deck Mounted Shower Mixer Tap - 4 Tap Hole
Single-person assembly
Tools required
We always recommend using professional
tradespeople to install your product
V2_4/ /2022

Congratulations on your purchase
And welcome to our growing gang of savvy shoppers
We're on a mission to bring you extraordinary bathroom products, for less. From modern
to traditional style ceramics, plus the gorgeous fixtures, fittings and furniture to match. So,
you can fall in love with your space every single day.
As one of the UK's largest independent bathroom stores, we've received countless
awards; including the National Business Awards UK, the Digital Entrepreneur Awards and
being placed on The Sunday Times Fast Track 100.
We hope your new product goes above and beyond your expectations. However, should
any problems occur, please:
log in to your account and contact our customer services team via your self-serve
portal – betterbathrooms.com/ ustomerAccount/Login
contact us via betterbathrooms.com/content/contact-us
Important information
Please read these instructions thoroughly and retain for future reference
Installation must be carried out in compliance with The Water Fittings Regulations
and Scottish Water Byelaws.
The system must be flushed prior to installation
Minimum and Maximum working pressure : 1 - 5 bar
Pressures must be equal for optimum performance
Please do not connect hot and cold water supply lines in reverse. This could result
in hot water flowing from cold line and cause scalding.
The feed-water temperature of water shall not exceed 85° .
Exceeding 85°may cause scalding, the service life of faucets might be shortened,
or the faucet might be damaged.
After installation, please make sure the faucet is securely mounted and checked for
leaks.

Parts / Diagrams
No Description No Description
1 Spout assembled 12 Switching device
2 Aerator with key 13 Locknut
3 Handle Hot 14 Switching handle
4 Headwork Hot 15 Handle old
5 O-ring 16 Headwork old
6 Base assembled 17 Shower holder assembled
7 Body 18 Hand shower
8 Fixing kit 19 onnecting hoses(to connect spout body
and hot& cold valves)
9 Base assembled for spout 20 Shower hose
10 Leg 21 Weight
11 onnector with Non-return valve
assembled
22 onnecting hoses(to connect hot&cold
valves with isolation valves)

Dimensions
Tools required
Spanner
Screwdriver

Installation
Remove the Screws, Locknuts, Metal Gaskets, and
Rubber Gaskets from the Legs of each body.
Drill 4 holes referring to the reference drawing at the
left. Recommened distance between each hole is
125mm.
From above, push the legs through holes on
bathtub.
From underneath the bathtub, secure the bodies
mixer by fixing the Rubber Gaskets, Metal Gaskets,
and Locknuts onto the legs, and finally fasten the
Locknuts and Screws by wrench and screwdriver.
onnect the hot valve and cold valve with the
isolation valves(not included) by connecting hoses,
hot on the left, cold on the right.
Loosen the screw on the weight by screwdriver, and
install it with the shower hose and tighten the screw.
onnect the shower hose with the spout body and
pull it out from the holder, and finally install the
shower hose with handshower.
Make sure the rubber washers are in the nuts of the
hoses.
Turn on water supply and check for leaks.

Operation
Troubleshooting
Issues Inspection Item
Poor water flow  Is there blockage within the filter mesh on
aerator(2)
Was the system flushed prior to installation
Is there debris inside the non-return valve(11)
Water leak Is there damage or dirt within the O-rings of the
headwork(4&16)
Is the headwork(4&16) fully tighten
Is there damage or dirt with the O-ring in th
aerator(2)
Is the locknut(13)fully tighten
Is there damage with the O-ring(5)
Is there damage with the O-rings under the
base(6,9)
Is there damage within the rubber washers and
inside the nuts of hoses(19,22,20)
Is there damage with the O-rings on the
hoses(19,20)
Is there damage within the rubber washer or O-
ring on the non-return valve(11)
Handle loose Is the screw inside the handles(3,15,14) fully
tightened
Is the locknut(13) tightened
Body loose Is the fixing kit(8) underneath fully tightened

Maintenance
Replacement of Cartridge Replacement of Aerator
Cleaning
To maintain the surface of your product, wipe with a clean damp cloth and wipe dry, do
not use any abrasive cleaning agents or materials. If any harsh chemicals come into
contact with the surface of the product, rinse and wipe clean immediately.