BluDot Chicago 3 Box User manual

Chicago 3 Box
DESIGNED IN 1997
ASSEMBLY NOTES | REV 04
@BLUDOT
We design all our pieces in our Minneapolis studio. Follow
along on Instagram for some sneak peeks into the process.
NEED A HAND?
Contact us at [email protected] or
844.425.8368 for assistance.

1 | 844.425.8368 CHICAGO 3 BOX
Upright
4QTY
Pt. 1001
24QTY
Pt. 5001
24QTY
Pt. 5005
24QTY
Pt. 5002
QTY 24
Pt. 8036
2QTY
8041
An�-�p Bracket
Pt. 8041
2QTY
Pt. 1217
QTY 2
Top panel
6QTY
Side panel
6QTY
Back panel
3QTY
Pt. 1218
2QTY
8042
An�-�p Strap
Pt. 8042
1QTY
Parts & Hardware

[e-mail] | 2ASSEMBLY NOTES
354
1 2
How to use the cam lock system
Note direction of cam arrow. Turn cam clockwise 1/2 turn or until tight. Note direction of cam arrow.

3 | 844.425.8368 CHICAGO 3 BOX
PT. 5001 x 12 PT. 5002 x 12 PT. 5005 x 12
Step 01
ATTACH THE SIDE PANELS (X3).
Attach the side panels to the top panel. See
page 2 for how to use the cam lock system.
Step 02
INSERT THE BACK PANEL (X3).
Slide the back panel between
the side panel grooves.

[e-mail] | 4ASSEMBLY NOTES
PT. 5001 x 12 PT. 5002 x 12 PT. 5005 x 12
Step 03
ATTACH THE TOP PANEL (X3).
Attach the top panel to the side panels. See
page 2 for how to use the cam lock system.

5 | 844.425.8368 CHICAGO 3 BOX
PT. 1001 x 8
Step 04
INSTALL THE STANDOFFS (X4).
Install standoff bolts in the lowest hole
locations as shown (x4).

[e-mail] | 6ASSEMBLY NOTES
Step 06
LEVEL THE UPRIGHTS.
Turn the adjustable glides to level the case.
Step 05
INSTALL UPRIGHTS.
Slide uprights one at a time through the holes
in the assembled box. After the legs have been
installed, have a second person help lift and
bring the case upright.

7 | 844.425.8368 CHICAGO 3 BOX
PT. 1001 x 8
PT. 1001 x 8
Step 07
INSTALL THE SECOND BOX.
Install standoff bolts in the center
hole locations as shown (x4). Slide
the box assembly over the uprights.
Step 08
INSTALL THE LAST BOX.
Install standoff bolts in the highest
hole locations as shown (x4). Slide
the box assembly over the uprights.

[e-mail] | 8ASSEMBLY NOTES
Back
Panel
Top
8041
An�-�p Bracket
PT. 8041 x 1PT. 1217 x 2
Step 9
INSTALL ANTI-TIP BRACKET TO CASE.
Bracket must be installed to top panel
of case.In order to prevent damage, it is
recommended that 7/64” pilot holes be
drilled prior to installation.
Rear of Case

CHICAGO 3-BOX9 | 844.425.8368
PT. 8036 x 2*
8041
An�-�p Bracket
PT. 8041 x 1PT. 1218 x 2
Step 10
ATTACH ANTI-TIP BRACKET TO THE WALL.
Wall anchors and fasteners are included for installation into
drywall. Please consult your local hardware professional to
determine the hardware best suited for your wall type.
Position the anti-tip bracket onto the wall 1” below case top panel
height as shown and mark hole locations with a pencil.
If the mounting locations are not positioned on a stud, drill 5/16”
clearance holes in the hole locations. Press wall anchors into
drilled holes.
If the hole locations are positioned on a stud, this step of
installing wall anchors may be skipped. Instead, drill 7/64” pilot
holes for the fasteners.
Secure anti-tip bracket in place using fasteners as shown.
1” lower than
case top
Side Panel
Wall

[e-mail] |10ASSEMBLY NOTES
8042
An�-�p Strap
PT. 8042 x 1
Step 11
SECURE THE CASE.
Install and tighten the strap
prior to using the product.

BLU DOT DESIGN & MANUFACTURING, INC. DESIGNED IN MINNEAPOLIS, MN
Additional Information
CLEAN
Clean with a slightly damp, soft cloth. To remove dirt
and fingerprints, use a quality cleaner formulated for
wood furniture. Wipe completely dry with a soft cloth
in the direction of the wood grain.