BMW 84 63 0 017 895 User manual

Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
BMW Motorola V50 / V3690 (dual band) hands-free retrofit kit
BMW 3 Series touring (E 46/3)
The installation time is approx. 5 hours, but this may vary depending on the condition of the car and the
equipment in it.
Retrofit kit No. 84 63 0 017 895
84 63 0 143 197
Parts and Accessories
Installation Instructions
046 0538 Z
TOP

EN/2
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
Contents
Section Page
Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1. Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Retrofit wiring harness connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Installation and cabling diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. To install and connect the retrofit wiring harness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5. To install and connect the hands-free control module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
6. To install and connect the eject box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7. To install the hands-free microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
8. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
9. Circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

EN/3
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
Important information
Only for use in the BMW dealer organisation.
Subject to technical modifications.
Installation information
Ensure that the cables/lines are not kinked or damaged as you install them in the car.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
Target group
The target group for these installation instructions is specialist personnel trained on BMW cars with the
appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and
work instructions in a rational order using the prescribed tools (special tools) and observing current health and
safety regulations.
Ordering instructions
A black insert for the centre console is supplied in the retrofit kit.
An insert for the centre console in other colours for cars with different interior colours can be ordered if
required. See the EPC for all further ordering information.
Safety instructions
Refer to the safety instructions for handling components of the airbag system. Further information is available
in the TIS in RA No. 32 34 ... If you fail to follow the safety instructions the airbag system may deploy
incorrectly and cause injuries.
List of special equipment
The following special equipment must be taken into consideration when installing the mobile phone.
SA 403 Glass roof
SA 602 On-board monitor
SA 606 Radio navigation system
SA 609 Navigation system
SA 660 BMW Reverse radio
SA 661 BMW Business radio
SA 662 BMW Business CD radio
SA 663 BMW Professional radio
Special tools required
DIS or MoDiC III

EN/4
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
1. Preparations
0
TIS instruction No.
Conduct a brief test
Disconnect the negative pole of the battery 12 00 ...
The following components must be removed first of all:
Boot trim on the left 51 47 151
Rear seat bench 51 24 005
Rear seat backrest 51 24 010
Front left door sill trim 51 47 000
Rear left door sill strip 51 47 030
Front left seat 52 .. ...
B pillar trim at the bottom left 51 43 150
Glove box, left 51 16 350
Pedal trim 51 15 185
A pillar trim in the left footwell 51 43 070
A pillar trim on the left 51 43 201
Left sun visor 51 16 080
Interior light 63 31 000
Glove box with casing, right 51 16 366
Oddments box support 51 16 ...
Finishing strips, centre and right 51 10 221
Heating system control 64 11 748
Radio 65 11 030
Oddments box 51 16 200

EN/5
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
2. Retrofit wiring harness connection diagram
0
0
Item Description Signal
Cable colour
/ Cross-
section
Connection location in the car Abbreviation / Slot
A Multi wiring harness --- --- --- ---
A1 SW 54-pin plug --- --- To hands-free control module adapter
branch B1
X4038
A2 Fakra plug contact --- --- To aerial resistor X13323
A3 SW 18-pin plug --- --- To eject box adapter branch
C1 X4545
A4 Fakra plug contact --- --- To eject box aerial connector X13322
A5 SW 10-pin plug LSP --- Cars with SA 660/661/662 only
To the radio plug
X13598
A6 Socket contact
Mute
Tel-On
WS/BR
0.35 mm
2
WS/GN
0.35 mm
2
Cars with SA 660/661/662 only
To the radio plug X18126
PIN 4
X18126
PIN 10
A7 Twin-lead terminal
SW 8-pin plug --- --- Between audio plugs X322
A8 SW 3-pin plug Mic --- To hands-free microphone X13293
A9 SW 3-pin plug --- --- To the aerial booster X1765
A10 Cable eyelet Terminal 31 --- To the earth post in the boot on the left X13016
A11 SW 12-pin plug LSP --- Cars with SA 602/606/609/663 only
To radio receiver plug X13321
A12 Socket contact
Mute
Tel-On
WS/BR
0.35 mm
2
WS/GN
0.35 mm
2
Cars with SA 602/606/609/663 only
To radio receiver plug X18126
PIN 10
X18772
PIN 11
A1
A12
A11
A5
A6
A3
A
A4
A2
A7
A8
A10
A9
046 0490 Z

EN/6
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
2. Retrofit wiring harness connection diagram
0
0
Item Description Signal
Cable colour
/ Cross-
section
Connection location in the car Abbreviation / Slot
B Hands-free control module adapter --- --- --- ---
B1 SW 54-pin plug --- --- To multi wiring harness branch A1 X4038
B2 SW 25-pin plug --- --- To hands-free control module X695
C Adapter eject box --- --- --- ---
C1 SW 18-pin plug --- --- To multi wiring harness branch A3 X4545
C2 SW 18-pin plug --- --- To interface X4545
B1 B2
B
C
C2
C1
046 0552 Z

EN/7
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
3. Installation and cabling diagram
0
Legend
A Multi wiring harness II
B Hands-free control module adapter
C Adapter eject box
0
1 Radio plug X18126 (with SA 660, 661, 662 only)
2 Hands-free microphone
3 Eject box and interface
4 Audio plug
X322
5 Hands-free control module
6 Radio plug
X18126 (with SA 602, 606, 609, 663 only)
7 Earth post
X13016
046 0755 Z
23
6
B
A
4
1
7
5
C

EN/8
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
4. To install and connect the retrofit wiring harness
0
0
0
0
0
Connect branches A1 and B1 in the boot on the left.
Connect the aerial resistor (1) between branch
A2 and
the standard aerial cable (2).
Wrap both plug connections in safety strips (3).
0
Screw branch A10 to earth post X13016 .
0
Cars with SA 660/661/662 only
Insulate branches A11 and A12 and tie them back.
Cars with SA 602/606/609/663 only
Disconnect plug X18126 from the radio receiver (1).
0
Connect branch A12 as follows to plug X18126 :
- WS/BR cable in PIN 10
- WS/GN cable in PIN 11
A1
1
2
33
B1
A2
046 0553 Z
X13016
A10
046 0741 Z
X18126
1
046 0723 Z
A12
X18126
046 0724 Z

EN/9
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
4. To install and connect the retrofit wiring harness
0
0
0
0
Connect branch A11 to plug X18126 .
If the plug
X13321 is already in the car, the two
cables from branch
A9 must be disconnected and
connected to the same pins in the plug in the car
X13321 . "
0
All cars
Install branches A3 – A8 as follows:
- Branches
A3 and A4 to the centre console.
- Branch
A8 to the A pillar.
Cars with SA 660/661/662 only
- Branches A5 – A7 to the radio.
Cars with SA 602/606/609/663 only
- Insulate branches A5 and A6 and tie them back.
0
All cars
Lay branch A8 to the installation site of the hands-free
microphone.
0
Disconnect plug X322 .
Connect branch
A7 in parallel between plug X322 .
A11
X18126
046 0725 Z
A8
A3-A4
A5-A7
046 0735 Z
A8
046 0736 Z
X322
A7
X322
046 0540 Z

EN/10
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
4. To install and connect the retrofit wiring harness
0
0
0
Cars with SA 660/661/662 only
Connect branch A6 as follows to plug X18126 :
- WS/BR cable in PIN 4
- WS/GN cable in PIN 10
0
Connect branch A5 to plug X18126 .
If the plug
X13321 is already in the car, the two
cables from branch
A9 must be disconnected and
connected to the same pins in the plug in the car
X13321 . "
X18126
A6
046 0740 Z
X18126
A5
046 0739 Z

EN/11
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
5. To install and connect the hands-free control module
0
0
0
0
0
Cars with SA 660/661/662 only
Insert the hands-free control module (1) into the holder
(2) and secure it with the bar (3) and a hexagonal screw
(4).
Connect branch
B2 to the hands-free control module (1).
0
Place speed nuts (1) in the side panel (2) on the left-hand
side of the boot.
0
Bolt the holder with the hands-free control module (1)
and retaining plate (2) to the left-hand side panel using
hexagonal screws and nuts (3).
0
Cars with SA 602/606/609/663 only
Insert square screws (1) into the holder (2).
B2 1
2
43
046 0559 Z
046 0560Z
1
2
046 0561 Z
23
1
046 0562 Z
1
2

EN/12
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
5. To install and connect the hands-free control module
0
0
0
Connect branch B2 to the hands-free control module (1).
Insert the hands-free control module (1) into the holder
(2) and secure it with the bar (3) and a hexagonal screw
(4).
0
Bolt the holder with the hands-free control module (1) to
the left-hand side wall plate (3) using hexagonal nuts (2).
B2 1
2
43
046 0559 Z
046 0563 Z
2
1
3

EN/13
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
6. To install and connect the eject box
0
0
0
0
0
Connect the telephone cable (1) to the eject box (2).
Insert the telephone cable (1) into the cable guide (3) and
clip the cable guide (3) together.
0
Clip the eject box (1) into the frame console (2).
0Clip the cable guide (1) into the frame console (2).
0Clip the frame console with the eject box (1) into the
oddments box (2).
3
1
2
046 0308 Z
1
2
046 0309 Z
1
2
046 0310 Z
1
2
046 0311 Z

EN/14
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
6. To install and connect the eject box
0
0
0
0
0Affix the foam strip (1) to the inside of the holder frame (2).
Place the interface (3) on the oddments box (4) and clip in
the holder frame (2).
0Connect the black 12-pin plug (1) for the eject box to the
interface (2).
Connect the black 6-pin plug (3) for the eject box to the
black 6-pin plug (4) for the interface (2).
0
The adapter cable Cmust be fitted."
Connect the eject box adapter C between the black
18-pin plug (1) on the interface and branch A3.
Connect the aerial plug (2) to branch A4.
0Wrap the plug connectors (1) in safety strips (2).
3
1
2
4
046 0312 Z
1
2
3
4
046 0313 Z
046 0726 Z
2
1
A3
A4
C
046 0727 Z
1
2

EN/15
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
7. To install the hands-free microphone
0
0
0
0
0Cars with SA 403 only
Connect branch A8 to the hands-free microphone (1).
The arrow on the hands-free microphone (1) must
point to the front of the car."
Clip the hands-free microphone (1) into the trim (2).
0Cars without SA 403 only
Only use the template from the installation kit."
Cut out the template (1) and affix it to the headlining
behind the opening for the interior light.
Cut the hatched area (3) out of the headlining.
0Push the metal frame (1) through the opening (2) and clip
it to the retaining frame (3).
0Connect branch A8 to the hands-free microphone (1).
The arrow on the hands-free microphone (1) must
point to the front of the car."
Clip the hands-free microphone (1) into the trim (2).
2
1
A8
046 0737 Z
1
2
3
039 0232 Z
2
1
3
039 0233 Z
2
1
A8
046 0738 Z

EN/16
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
8. Concluding work
This retrofit system does not require coding."
- Conduct a brief test with DIS/MoDiC III.
- Conduct a function test
- Re-assemble the car

EN/17
Retrofit kit No. 84 63 0 017 895/ 84 63 0 143 197
Installation Instructions No. 01 29 0 143 752 Issue date: 04.2002
9. Circuit diagram
The circuit diagrams for the retrofit telephone system are available if required on the installation
instructions CD entitled “Circuit diagrams for retrofit telephones UNI II”."