Bob's Space Racers Jersey Wheels User manual

OPERATOR’S MANUAL
Bob’s Space Racers®Inc. ©1976-2020
427 Whac-A-Mole Way,
Holly Hill, Florida 32117
Phone - [phone]
Fax - [phone]
E-mail: [email protected]
Jennison Entertainment Technologies
822 South Nova Road
Daytona Beach, Florida 32114
Phone - 1-(386)-255-1599
Fax: [phone]
E-mail: [email protected]

Bob's Space Racers® Inc. ©1976-2019 ii
Table of Contents
I.
JERSEY WHEELS ARCADE OPERATOR’S MANUAL
A.
Introduction ……………………………………………………………….………..
iii
A.1: Overview ………………………………………………………….…………
iii
A.2: Use only a GROUNDED AC receptacle. ………...………………….……..
iii
A.3: Maintenance for the Games ………..…………………………………….…
iii
A.4: Average Power Requirements ……………………………………….………
iii
A.5: Packing List ………………………………………………………………...
iii
A.6: Tools ………………………………………………………………………...
iv
A.7: Parts Kit Contents from Figure A.4 ………………………………………...
iv
B.
Setup …………………………………………………………………………….…
v
B.1 The initial setup up of the game ……………………………………………..
v
B.2 Assembling a Jersey Wheel ………………………………………………….
v
B.3 Hooking up the Connections …………………………………………………
vii
Chapter 1 :
Operator’s Procedure ....................………………………….……………….
1-1
1.1: Object of Game ……………………………………………………….
1-1
1.2: Operate / Race ………………………………..………….…………...
1-1
Chapter 2 :
Maintenance ……………………..………………………………………….
2-1
2.1: Maintenance Recommendations …………….……………….………
2-1
2.2: Periodic Maintenance …………………………………………………
2-1
Chapter 3 :
Troubleshooting …………….………..………..……………………………
3-1
3.1: Troubleshooting Philosophy ..………………………………………...
3-1
3.2: Motor Belt Errors …………………….……………………………...
3-1
3.3 Error Codes …………………………………………….……………..
3-1
3.4 Solution A (Errors 7-10) ………………………………………………
3-1
3.5 Solution B (Errors 11-14) ……………………………………………..
3-2
3.6 Motor Belt Errors ……………………………………………………..
3-2
3.7 Sensor Break or Home Break Error …………………………………..
3-2
Chapter 4 :
Option Settings –Jersey Wheels ……….…………………………………...
4-1
Chapter 5 :
Service …………………………………………………..…………………..
5-1
5.1 Calling for Service …………………………………………………….
5-1
Appendix A :
Policies ……………………………………………………………..……….
A-1
A.1: Service Policy ………………………………………………………..
A-1
A.2: Advance Replacement Policy …………………………………..…….
A-1
Appendix B :
Warranty …………………………………..………………………………..
B-1
B.1: Game warranty ……………………………………………………….
B-1
B.2: Advanced replacement item(s) shipping requirements ………..….….
B-2
Appendix C :
Federal Communications Commission statement …………………………..
C-1
Appendix D :
Parts …...………………………….………………………………………...
D-1
D.1: Customer Parts List ……………………………………………..…....
D-1
Appendix E :
Wire Diagram …...…………………………………………………..………
E-1
Appendix F :
Revision ……………………………………………………………..………
F-1

Bob's Space Racers® Inc. ©1976-2018 iii
A. Introduction
A.1 Overview
This manual contains information about the Arcade Game Jersey Wheels™, including: Setup, tools,
instructions how to play, maintenance, tech tips, troubleshooting, game options settings, and service.
Appendixes A-C contain information about policies, warranty, and service. Appendix D has a list part(s)
pertaining to this specific game.
A.2 Use only a GROUNDED AC Receptacle.
Failure to do so could result in improper operation or damage to the game and could void your warranty. If
you are unsure that your AC receptacle is properly grounded, have a qualified electrician perform this check
for you.
A.3 Maintenance for the games
Always be sure power to the game is turned off when performing even routine maintenance. Otherwise
moving parts could activate unexpectedly and or cause injury.
A.4 Average Power Requirements Amperage & Watts will vary depending on game.
Voltage
Amps
Watts
Hertz
Service Power
Recommendation
A.4.1
3/4-Wheel Version:
110V ± 10V
~ 3.6 Amps
~ 400 W
at 50/60Hz
8 Amps
A.4.2
3/4-Wheel Version:
230V ± 10V
~ 1.8 Amps
~400 W
at 50/60Hz
5 Amps
WARNING!
Ensure that this product is compatible with your facilities power supply, voltage and frequency requirement.
A label describing Electrical Specifications is attached to the product. Non-compliance with the Electrical
Specifications can cause a fire and electric shock. Ensure the game is level before applying power.
A.5 Packing List
Check the packing list prior to installation. Verify that all parts that have been received and are in good condition.
Base
Marquee
2nd Sign Bracket
Part’s Kit
Figure A.1
Figure A.2
Figure A.3
Figure A.4
Back Supports
Side Signs
3-Wheel Version Top
Section Only
4-Wheel Version Top
Section Only
Figure A.5
Figure A.6
Figure A.7
Figure A.8

Bob's Space Racers® Inc. ©1976-2019 iv
A.6 Tools
#2 Phillips Screwdriver
Ratchet
17mm Socket
8-foot ladder
At least Two Helpers
Figure A.8
Figure A.9
Figure A.10
Figure A.11
Figure A.12
8mm
5mm
4mm
3mm
2.5mm
Figure A.13
Figure A.14
Figure A.15
Figure A.16
Figure A.17
A.7 Parts Kit Contents from Figure A.4
Spring | Intergrated Chips | Fuse | Pointer Placement
Marquee
Mounting Bolts
Rear Cabinet Support Brace Mount
Figure A.18
Figure A.19
Figure A.20
Sign Mounting Bolts | Wheel Mounting Bolts | Rear Cabinet Support Mounting Bolts
Wrenches
Figure A.21
Figure A.22
Power Cable
Allen Keys
Figure A.23
Figure A.24

Bob's Space Racers® Inc. ©1976-2019 v
B. Setup
B.1 Steps to setup a Jersey Wheels™ game.
B.1.1 Initial setup involves creating a location for the game.
B.1.2 Assembling the game, see Section B.2.
B.1.2 Make necessary game connections, see Section B.3.
B.1.3 Hook up the power to the game.
Please Note: If there is a problem, call BSR’s technical support: 386-677-0761.
B.2 Assembling a Jersey Wheel
B.2.1 Below is Figure B.2 which is a 3-Wheel Jersey Wheels™illistration. This visual aid will
help show which hardware to use to assemble Jersey Wheel. The 4-Wheel version is shown below
with Figure B.11.
B.2.2 Take the pallet close to the placement of the Arcade then removing all parts off the pallet. A
8-foot ladder (Figure A.10) will help assist when assembling the game.
B.2.3 The 3-Wheel version, install the third wheel, using the hardware as seen in Figure B.2 and a
17mm socket to tighten the bolts.
B.2.4 The 4-Wheel version, install the thrid wheel, using the hardware as seen in Figure B.12 and
a 17mm socket to tighten the bolts and then repeat the same procedure when installing the fourth
wheel .
B.2.5 Mounting the Marquee is the same for either the 3-Wheel or 4-Wheel version. First remove
the back panel with a #2 Phillps screwdriver, then place the Marquee into place on the top of the
third or fourth wheel. Then secure with the five bolts shown in Figure B.4 or Figure B.13, the
bolts are a 4mm Allen.
B.2.6 Install the second Sign Bracket (Figure B.5). On the 3-Wheel version the bracket is installed
onto the second wheel, see Figure B.2. There are three 5mm Allen bolts to secure this bracket. See
Figure B.5, B.4, & B.2.
B.2.6 Install the second Sign Bracket (Figure B.11). On the 4-Wheel version the bracket is
installed onto the thrid wheel, see Figure B14 . There are three 5mm Allen bolts to secure this
bracket. See Figure B.15, B.14, & B.11.
B.2.7 Next, install the signs. Figure B.6 or B.15 shows the 5mm Allen bolts to use to install the
signs. The letters JERSEY will be installed on the Left side, where WHEELS will be installed
onto the Right side of the game. Be sure to connect the wires to the signs, see Figure B.7 or in
Figure B.16, before completely securing the signs.
B.2.8 To ensure the arcade game does not move around, BSR recommneds to install the back
support braces. Figure B.8 –B.10, illistruates the 3-Wheel version and Figures B.17-B.19
illistrates the 4-Wheel version, how to mount the brackets and secure them to the game. A 17mm
socket and impact drill can reduce the time spent tighting this down. Once the arcade is place in
its final destination turn the stabilizers (Figure B.8 or B.18) into place until fully stable.

Bob's Space Racers® Inc. ©1976-2019 vi
Figure B.3
Figure B.6
Figure B.4
Figure B.9
Figure B.2
Figure B.8
Figure B.5
Mounting
Bolts
Figure B.7
Figure B.10
Stabilizer

Bob's Space Racers® Inc. ©1976-2019 vi
Figure B.12
Figure B.15
Figure B.13
Figure B.18
Figure B.11
Figure B.17
Figure B.14
Mounting
Bolts
Figure B.16
Figure B.19
Stabilizer

Bob's Space Racers® Inc. ©1976-2019 vii
B.3 Hooking up the Connections
Depending on the 3-Wheel or 4-Wheel version of Jersey Wheels™ have cable which needs to be
connected. Each version will have the base cabinet and two wheels on top. The third wheel on a 3-Wheel
Jersey wheel will require the same connections as a 4-Wheel Jersey Wheel™ from the second wheel to
the third wheel.
B.3.1 In Figure B.20 there are only two cables which need to be connected to the I/O board.
B.3.1.1 Connection 5 is a 20-pin cable, which transfers power from the below wheel and
supplies power to the wheel being connected.
B.3.1.2 Connection 9 is a 34-pin ribbon cable, which will be connected to the bottom 34-
pin connector of the I/O board. This cable allows the master board to communicate to this
I/O board.
B.3.2 The Marquee’s harness (Figure B.21) shows three cables which need to be connected. There
is a (1) 20-pin connector, (2) 3-Pin connector, and a (3) 2-pin connector. Note: The 3-pin cable is
usually located in the second wheel. Fish it up through the other wheel(s) and connect it to the marquee
harness.
Figure B.20
Figure B.21
Note: See Appendix E for wiring diagram
CN5
Receives / Connects Power from previous
wheel or base
CN6
Power to Wheel (Present Wheel)
CN7
Sends power from present wheel to next
IO board (goes to CN5 of the next wheel)
above.
CN8 (Communication Ribbon Cable)
Sends Data to next IO board of the next
wheel above.
CN9 (Communication Ribbon Cable)
Receives Data from Motherboard /
Previous IO board.

Bob's Space Racers® Inc. ©1976-2019 1-1
Chapter 1: Operator’s Procedures
1.1 Object of Game.
Kick up the game and watch the wheels spin. The bottom wheel will start first. Press the flashing button
after it turns green. Land on the Bonus on each wheel to receive the ultimate number of tickets.
1.2 Operate / Race
3-Wheel Version
Stops here.
4-Wheel Version
Stops here.

Bob's Space Racers® Inc. ©1976-2019 2-1
Chapter 2: Maintenance
2.1 Maintenance Recommendations
2.1.1 Clean the outer surfaces of the game with an All-purpose cleaner, which is non-corrosive and
nonabrasive.
2.1.2 DO NOT USE commercial chemical sprays on vinyl graphics.
2.1.3 DO USE a good quality spray type furniture polish to keep the game looking good.
2.1.4 Vacuum the inside of the game occasionally to help keep the dust and ticket debris off of all the
electronics.
2.2 Periodic Maintenance
2.2.1 Daily Cleaning
2.2.1.1 Cleaning Cabinet (Simple Green™ or other non-corrosive general purpose cleaners)
2.2.1.2 Cleaning Plexiglas (Windex®, Clean-On-The-Go Glass®, Brillianize®)
2.2.2 Daily Check
2.2.2.1 Check individual unit coin switches or swipe card unit.
2.2.2.3 Check to see that the turns on and initializes properly.
2.2.2.4 Check all lights.
2.2.2.7 Check each wheel for proper motion.
2.2.2.8 Check to see that all wheels and moving parts are work properly. Repair as needed.

Bob's Space Racers® Inc. ©1976-2019 3-1
Chapter 3: Troubleshooting
3.1 Troubleshooting Philosophy. When troubleshooting any product, certain general guidelines should be followed.
3.1.1 Always check to be sure that your game power is turned on. Ensure that all of the fuses in the
game are functional and that the AC voltage is in the proper operating range for your game.
3.1.2 Ensure that all of the game harnessing is plugged in properly and that all of the pins are firmly
seated in the connectors. It is always possible that a harness can be damaged by rough shipping or
moving.
3.1.3 Inspect game harnessing to be sure that none of the wires have become or are damaged. Utilize
a handheld multi-meter, and check continuity of the wires to make sure they are not broken.
3.1.4 Inspect for obvious damage to the P.C. Boards or electrical components.
3.1.5 If you have multiple similar games or multiple parts for a game, swap or exchange the parts to
see if the problem goes away or moves to another location. You can quickly eliminate certain parts
as being the problem within the game.
3.1.6 When changing electronic or electrical components, ALWAYS turn off all external power and
unplug the game.
3.1.7 Ensure that all power supplies are delivering the specified voltages to the P.C. Boards and
components as shown in the manual.
3.2 General Function Errors
Game will not function with the following errors.
Error Code
Problem
Solution
Err1
Error Wheel #1
Indicates a problem on wheel #1 that could affect the
accuracy of scoring. Check the location of the break,
alignment, and or the sensor.
Err2
Error Wheel #2
Indicates a problem on wheel #2 that could affect the
accuracy of scoring. Check the location of the break,
alignment, and or the sensor.
Err3
Error Wheel #3
Indicates a problem on wheel #3 that could affect the
accuracy of scoring. Check the location of the break,
alignment, and or the sensor.
Err4
Error Wheel #4
Indicates a problem on wheel #4 that could affect the
accuracy of scoring. Check the location of the break,
alignment, and or the sensor.
3.6 Motor Belt Errors
Game will still function properly with the following errors however, the game will not score properly. These will only
be shown on start-up during initialization.
Error Code
Problem
Solution
BLT1
Belt Wheel #1
Indicates the motor belt for wheel #1 is either too loose
or too tight, adjust as necessary.
BLT2
Belt Wheel #2
Indicates the motor belt for wheel #2 is either too loose
or too tight, adjust as necessary.
BLT3
Belt Wheel #3
Indicates the motor belt for wheel #3 is either too loose
or too tight, adjust as necessary.
BLT4
Belt Wheel #4
Indicates the motor belt for wheel #4 is either too loose
or too tight, adjust as necessary.

Bob's Space Racers® Inc. ©1976-2019 3-1
3.7 Sensor Break or Home Break Error
Game will still function properly with the following errors, however the game will not score properly. These will only
be shown on start-up during initialization.
Error Code
Problem
Solution
Pin1
Pin (Break) Wheel #1
Indicates that either the home position break or another
break is not being read on wheel #1. Check the
location of the break and or check the sensor.
Pin2
Pin (Break) Wheel #2
Indicates that either the home position break or another
break is not being read on wheel #2. Check the
location of the break and or check the sensor.
Pin3
Pin (Break) Wheel #3
Indicates that either the home position break or another
break is not being read on wheel #3. Check the
location of the break and or check the sensor.
Pin4
Pin (Break) Wheel #4
Indicates that either the home position break or another
break is not being read on wheel #4. Check the
location of the break and or check the sensor.

Bob's Space Racers® Inc. ©1976-2019 4-1
Chapter 4: Option Settings –Jersey Wheels
4.1 Jersey Wheels IO Settings Version 3.1
Options for the Jersey Wheels are set by three dip switch blocks (SW1, SW2, SW3), see Figure 4.2 &
4.3). By flipping the white tab upwards towards the “ON”, as seen in Figure 4.1, will activate an option
setting. Each Switch has a set of combinations. Below in Figure 4.6 shows how each switch needs to be
set to utilize the different options settings.
Note: To set up game play Options and tickets payouts refer to I/O Settings Version 3.1 in Figure 4.6.
4.1.1 For ticket options refer to payout chart below in figure 4.4 and 4.5 to set the ticket value and
cost to play chart.
Note: If ticket output is too low or high, raise or lower one letter at a time until proper payout is achieved. It is
recommended to check two weeks of payout before changing.
Switch 1
Switch 2
Switch 3
Figure 4.1
Figure 4.2
Figure 4.3
Figure 4.4
Figure 4.5

Bob's Space Racers® Inc. ©1976-2019 4-2
Figure 4.6

Bob's Space Racers® Inc. ©1976-2019 5-1
Chapter 5: Service
5.1 Calling for Service
5.1.1 When calling for service, please check the operator’s manual first. You may find a solution to
your problem within this manual.
5.1.2 Please make sure you have the serial number of the game ready when you call.
5.1.3 If this is a repeat call, please tell the service technician that you have made a previous call
regarding this problem. This way we will be able to retrieve the history on your game allowing us to
efficiently serve you better.
5.1.4 Please retain serial number for your product. This may be requested for warranty repairs.
5.1.5 If at all possible, please call us from and with access to the game as we may need you to check
certain things on the game while we are on call with you.
IF YOU HAVE ANY
QUESTIONS OR COMMENTS
PLEASE CALL BSR.
BSR’s Parts Contact Info
Phone: [phone]
Opened: Monday –Friday
Office Hours: 8:30AM –5:00PM EST
E-mail: [email protected]
EXCLUDING HOLIDAYS
BSR’s Tech Contact Info
Phone: [phone]
Opened: Monday –Friday
Office Hours: 8:30AM –5:00PM EST
Has afterhours support, charges may apply.
E-mail: [email protected]
EXCLUDING HOLIDAYS
Visit Our Website for More Information
WWW.BOBSSPACERACERS.COM
A great resource on our website is the CUSTOMER “SUPPORT” page.

Bob's Space Racers® Inc. ©1976-2019 A-1
Appendix A: Policies
A.1 Service Policy
A.1.1 Here at BOB’S SPACE RACERS®INC., we pride ourselves in providing the highest quality,
long lasting, and easy to maintain equipment.
A.1.2 Technical Support Service hours are from 8:30 am to 5:00 pm, EST, Monday through Friday,
excluding holidays. The direct technical number is [phone] ext:146. During all other times,
follow the prompts on our Automated Phone System to relay your problem to the technician on call.
Technical Support will assist you in troubleshooting a service problem or setting equipment options.
A.1.3 You can also e-mail your technical question to: [email protected].
A.1.4 Customer Service hours are from 8:30 am to 5:00 pm, EST, Monday through Friday, excluding
holidays. Customer Service staff can be reached at [phone]. They will also take parts orders
and research the status of previous orders.
A.2 Replacement Policy
A.2.1 After speaking with our Technical Department it may be necessary for Bob’s Space Racers®
Inc., to ship an assembly item or part to repair your game.
Note: We will not ship anything to P.O. Boxes via the US Postal Service. You will be billed per your account status for the total cost
of the shipment, which includes shipping charges.
A.2.2 Upon shipment of the new item(s) a Return Merchandise Authorization Number (RMA #) will
be issued for you to use when returning the defective item(s) to Bob’s Space Racers® Inc., or you
may use the order number. After the defective item(s) is received by Bob’s Space Racers® Inc. your
account will be issued either a:
A.2.2.1 Warranty credit: if your game is under warranty. See the Warranty Policy page.
Note: this credit does not include return shipping charges.
A.2.2.2 Credit for the item(s).
Note: this credit does not include return shipping charges, nor does it include the repair charges for the item(s).

Bob's Space Racers® Inc. ©1976-2019 B-1
Appendix B: Warranty
B.1 Game Warranty
BOB’S SPACE RACERS® INC. ©2019
90 DAYS GAME WARRANTY
B.1.1 INCLUDED IN THIS WARANTY Bob’s Space Racers® Inc., warrants to the original purchaser only that the equipment that is the
subject of this sale conforms to its specifications, and is free from defects under normal service for 90-days period from the original date of
deliver. This warranty does not include any damages resulting from occurrences listed in paragraph 2 below. This warranty is not transferable
under any circumstance. Any claims under this warranty must be received in writing by Bob’s Space Racers® Inc. within 90-days from date
of delivery. Within a reasonable time of such written notification Bob’s Space Racers® Inc. will replace or repair any defective component
of the equipment or part thereof which fails for reasons other than normal service, use, or wear. Bob’s Space Racers® Inc. reserves the right
to request dated proof of purchase by the end user (original purchaser) at any time. Bob’s Space Racers® Inc., within its sole discretion,
makes the final determination as to whether to repair or replace any component and whether any such repair or replacement shall be performed
where the equipment is located or at its home facility in Volusia County, Florida, or another facility of its sole choice. Any and all freight
charges for the purposes of repair or replacement shall be paid by the original purchaser. All defective parts shall be returned to Bob’s Space
Racers® Inc. if requested. Bob’s Space Racers® Inc. does not warrant that the equipment will meet any original purchaser’s specific
requirements or that the operation of the equipment will be uninterrupted. These remedies are the original purchaser’s exclusive remedies for
breach of warranty.
B.1.2 EXCLUDED BY THIS WARRANTY Bob’s Space Racers® Inc. does not warrant (a) any product, components or parts not
manufactured by Bob’s Space Racers® Inc.; light bulbs are excluded and shall be the sole responsibility of the purchaser; (b) damages caused
by use of the equipment for purposes other than those for which it was designed; (c) defects caused by failure to provide a suitable installation
environment for the equipment; (d) damage caused by unauthorized attachments, modification, or service; damage caused by normal wear
and tear or improper power supply; (f) damage caused by accident or disaster such as fires, flood, lightning, and wind; or (g) any other abuse
or misuse of the equipment.
B.1.3 EXCLUSIVE WARRANTY. THE FORGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES OR REMEDIES, WHETHER WRITTEN, ORAL OR IMPLIED. THERE ARE NO WARRANTIES WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. ANY AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, COURSE OF DEALING OR USAGE OF TRADE
ARE HEREBY EXPRESSLY DISCLAIMED AND EXCLUDED.
B.1.4 REMEDIES LIMITED. UNDER NO CIRCUMSTANCES, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
SHALL BOB’S SPACE RACERS® INC. BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR INDIRECT, SPECIAL INCIDENTAL
OR CONSEQUENTIAL ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT INCLUDING BUT NOT LIMITED
TO ANY CLAIM FOR LOSS OR PROFITS, LOSS OF SAVINGS OR REVENUE, LOSS OF USE OF THE EQUIPMENT, OR ANY
ASSOCIATED EQUIPMENT, FACILITIES OR SERVICE, DOWNTIME, THE CLAIMS OR COSTS OF THIRD PARTIES INCLUDING
CUSTOMERS AND INJURY TO PROPERTY. Some states do not allow limitations on how long an implied warranty lasts or the exclusion
or limitation of incidental or consequential damages, so the above limitations or exclusion may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
B.1.5 NO OTHER WARRANTIES. Unless modified in writing and signed by both parties, this agreement
is understood to be the complete and exclusive agreement between the parties, superseding all prior
agreements, oral or written, and all other communications between the parties relating to the subject matter
of this agreement. No employee or representative of Bob’s Space Racers® Inc. or any other party is
authorized to make any other warranty or to assume any other liability in connection with the sale of its
equipment.

Bob's Space Racers® Inc. ©1976-2019 B-2
B.1.6 TIME LIMIT FOR CLAIMS. Any claim for breach of warranty or claims under this warranty must be received in writing by Bob’s
Space Racers® Inc. within 90-days following delivery of the equipment.
B.1.7 FUTURE CHANGES. Bob’s Space Racers® Inc. reserves the right to reserve, change or modify the construction and design of its
equipment or any component part or parts thereof without incurring the obligations to make such changes or modifications in present
equipment.
B.1.8 ALLOCATION OF RISKS. This agreement allocates the risks of equipment failure between Bob’s Space Racers® Inc. and the
original purchaser. This allocation is recognized by both parties and is reflected in the price of the goods. THE PURCHASER
ACKNOWLEDGES THAT HE HAS READ THIS AGREEMENT, UNDERSTANDS IT, AND IS BOUND BY ITS TERMS.
B.1.9 TO OBTAIN WARRANTY SERVICE. The original purchaser must, at his/her own expense, bring or ship the equipment to an
authorized location for service. Additionally, the original purchaser must pay all freight, shipping or transportation charges for the return of
the equipment from Bob’s Space Racers® Inc. to the original purchaser.
B.2 Replacement Item(s) Shipping Requirements
B.2.1 When you request an Advanced Replacement item from us, we recommend you to follow
B.2.2 DO NOT try to repair the defective item(s) on your own; DO NOT disassemble the defective item(s) prior to returning it to Bob’s
Space Racers® Inc. –this could cause further damage and the possibility of you not receiving any credit at all on the item(s). There are no
user serviceable parts contained within, and our vendors may void their warranty on disassembled parts.
B.2.3 Wait for the Replacement item(s) to arrive prior to returning the defective item(s).
B.2.4 When the Replacement item(s) arrive, verify that it is the correct part. If it is not, please note what the differences are and contact
Bob’s Space Racers® Inc. at 386-677-0761.
B.2.5 Return the defective item(s) in the exact same packaging the Replacement item(s) came in. This insures no more damage will be done
to the item(s) during the return shipping.
Thank You!

Bob's Space Racers® Inc. ©1976-2019 C-1
Appendix C: Federal Communications Commission (FCC) Statement
C.1 FCC Statement
C.1.1 This equipment has been tested and found to comply with limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate frequency energy, and, if not installed and used in accordance with
the instruction manual may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his/her own expense.
Note:
All games from Bob’s Space Racers® Inc. are shipped with the same factory keys and lock sets. Bob’s Space Racers® Inc.
recommends changing the keys and locks on your games upon receipt.

Bob's Space Racers® Inc. ©1976-2019 D-1
Appendix D: Parts List
D.1 Customer Parts List
Part #
Descriptions
Picture
TBD
Master Board
TBD
Wheel Position Sensor
TBD
Wheel Sensor Breaks
(Please Specify Size When Ordering)
TBD
Wheel Cover
(Please Specify which Wheel Cover When Ordering)
TBD
Wheels
(Please Specify Which Wheel When Ordering)
TBD
LED Lights
(Please Specify When Ordering)
TBD
Wheel Frame Front Border Set
(Please Specify Which Wheel & Color When Ordering)