Body Craft BC-F431 User manual

TF-
~ 60 Min.
CM
BCF431.01.02
Art. No. BC-F431
Assembly and Operating Instructions
BodycraftLat pull and pulley for F430
L 87 | W 119 | H 210

2F431

3
Content
1 GENERAL INFORMATION 7
1.1 Technical Data 7
1.2 Personal Safety 8
1.3 Set-Up Place 9
2 ASSEMBLY 10
2.1 General Instructions 10
2.2 Scope of Delivery 11
2.3 Assembly 12
3 STORAGE AND TRANSPORT 16
3.1 General Instructions 16
4 TROUBLESHOOTING, CARE AND MAINTENANCE 17
4.1 General Instructions 17
4.2 Faults and Fault Diagnosis 17
4.3 Maintenance and Inspection Calendar 18
5 DISPOSAL 18
6 RECOMMENDED ACCESSORIES 19
7 ORDERING SPARE PARTS 20
7.1 Serial Number and Model Name 20
7.2 Parts List 21
7.3 Exploded Drawing 23
8 WARRANTY 24
9 CONTACT 26

4F431

5
Dear customer,
thank you for choosing training equipment of the brand Bodycraft. Bodycraft equipment inspires
with its multifunctionality and excellent quality. In terms of innovation and technology, it is one of
the highest quality tness equipment for home use. Bodycraft multi gyms, for example, oer a very
wide range of exercise possibilities. This ranges from traditional strength training such as bench
presses and rehabilitation exercises to workout for complex sports like golf, tennis or badminton.
Disclaimer
BodyCraft® is a registered brand of the company Fitness Authority Industrial Co., LTD. All rights
reserved. Any use of this trademark without the explicit written permission of Fitness Authority
Industrial Co., LTD is prohibited.
Product and manual are subject to change. Technical data can be changed without advance notice.
Intended Use
The equipment may only be used for its intended purpose.
The equipment is only suitable for home use. The equipment is not suitable for semi-professional
(e.g. hospitals, associations, hotels, schools, etc.) and commercial or professional use (e.g. tness
studios).

6F431
ABOUT THIS MANUAL
Please carefully read the entire manual before installation and rst use. The manual will help you to
quickly set up the system and explains how to safely use it. Make sure that all persons exercising with
the equipment (especially children and persons with physical, sensory, mental or motor disabilities)
are informed about this manual and its contents in advance. In case of doubt, responsible persons
must supervise the use of the equipment.
Due to ongoing changes and software optimisations, the manual may have to be updated. If
you notice any discrepancies during assembly or use, please refer to the manual uploaded to the
webshop. The latest manual is always available there.
This equipment has been manufactured according to the latest safety knowledge. As far as possible,
potential safety hazards which could cause injury have been eliminated. Make sure to carefully follow
the instructions and that all parts are securely in place. If required, read through the
instructions again to correct any mistakes.
Please pay close attention to the safety and maintenance instructions given here.
The contract partner cannot be held liable for damage to health, accidents or
damage to the equipment when it is not used in accordance with these instructions.
The following safety instructions may appear in this manual:
࣑ATTENTION
This notice indicates potentially hazardous situations which, if not avoided, may result in
property damage.
⚠CAUTION
This notice indicates potentially hazardous situations which, if not avoided, may result in slight
or minor injuries!
⚠WARNING
This notice indicates potentially hazardous situations which, if not avoided, may result in death
or serious injuries!
⚠DANGER
This notice indicates potentially hazardous situations which, if not avoided, will result in death
or serious injuries!
LNOTICE
This notice indicates further useful information.
Retain these instructions in a safe place for future reference, maintenance or when ordering
replacement parts.

7
1 GENERAL INFORMATION
1.1 Technical Data
Weight and Dimensions:
Package dimensions (L x W x H) approx.:
No. 1: 124 cm x 35 cm x 17 cm
No. 2: 217 cm x 8 cm x 5 cm
Article weight (gross, incl. packaging):
No. 1 26.2 kg
No. 2 5.1 kg
Set-up dimensions (L x W x H) approx.: 86.9 cm x 119.4 cm x 209.5 cm
Transmission ratio: 1:1

8F431
1.2 Personal Safety
⚠DANGER
+ Before you start using the equipment, you should consult your physician that this type of
exercise is suitable for you from a health perspective. Particularly aected are persons who:
have a hereditary disposition to high blood pressure or heart disease, are over the age of 45,
smoke, have high cholesterol values, are overweight and/or have not exercised regularly in
the past year. If you are under medical treatment that aects your heart rate, medical advice
is absolutely essential.
+ Note that excessive training can seriously endanger your health. Please also note that
heart rate monitoring systems can be inaccurate. If you notice any signs of weakness,
nausea, dizziness, pain, shortness of breath, or other abnormal symptoms, stop exercising
immediately and seek advice from your doctor if necessary.
⚠WARNING
+ This equipment may not be used by children under the age of 14.
+ Children should not be allowed unsupervised access to the equipment.
+ Persons with disabilities must have a medical license and must be under strict observation
when using the equipment.
+ The equipment is strictly for use by one person at a time.
+ If your equipment provides a safety key, the clip of the safety key must be attached to your
clothing before starting your training. In the event of a fall, the EMERGENCY STOP of the
equipment can be initiated.
+ Keep your hands, feet and other body parts, hair, clothing, jewellery and other objects well
clear of moving parts.
+ During use, wear suitable sports clothing rather than loose or baggy clothing.When wearing
sports shoes, make sure they have suitable soles, preferably made of rubber or other non-
slip materials. Shoes with heels, leather soles, studs or spikes are unsuitable. Never exercise
barefoot.
⚠CAUTION
+ If your equipment needs to be connected to the power supply with a mains cable, make
sure that the cable is not a potential tripping hazard.
+ Make sure that nobody is within the range of motion of the equipment during training so as
not to endanger you or other persons.
࣑ATTENTION
+ Do not insert any objects of any kind into the openings of the device.

9
1.3 Set-Up Place
⚠WARNING
+ Do not place the equipment in main corridors or escape routes.
⚠CAUTION
+ Choose a location in which to place the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The training room should be well ventilated during training and not be exposed to any
draughts.
+ Choose the place in which to set up the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The set-up and mounting surface of the equipment should be at, loadable and solid.
+ If your device is to be mounted on the wall/ceiling, make sure that you use the appropriate
assembly material to avoid possible damages or personal injuries. The contractual partner
accepts no liability for this.
࣑ATTENTION
+ The device may only be used in one building, in suciently tempered and dry rooms
(ambient temperatures between 10°C and 35°C). The equipment should not be used
outdoors or in rooms with high humidity (over 70%) like swimming pools.
+ A oor protective mat/equipment underlay can help to protect high-quality oor coverings
(parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight
unevenness.

10 F431
2 ASSEMBLY
2.1 General Instructions
⚠DANGER
+ Do not leave any tools, packaging materials such as foils or small parts lying around,
as otherwise there is a danger of suocation for children. Keep children away from the
equipment during assembly.
⚠WARNING
+ Pay attention to the instructions attached to the equipment in order to reduce the risk of
injuries.
⚠CAUTION
+ Ensure to have sucient room for movement in each direction during assembly.
+ The assembly of the equipment must be carried out by at least two adults. If in doubt, seek
the help of a third technically skilled person.
࣑ATTENTION
+ To prevent damage to the equipment and the oor, assemble the equipment on a mat or
packaging board.
LNOTICE
+ In order to make the assembly as simple as possible, some screws and nuts to be used can
already be pre-assembled.
+ Ideally, assemble the equipment at its later set-up place.

(51) BASE FRAME
(58) TWO WAY
TOP PLATE
(60) LOW
ROW BAR
(63) 45mm
X 75mm PLUG
X 4pcs
(71) SNAP HOOK
X 2pcs
(73) 1" SPRING
CLIP X 2pcs
(74) LOW CABLE
(74A) TOP CABLE
(64) PULLEY
X 7pcs (65) RUBBER
DONUT X 4pcs
(70) LOW ROW
CHAIN (21 LINK)
(62) 75mm
X 45mm CAP
X 3pcs
(61) STACK
SPACER 24"
X 2pcs
(59) LAT BAR
(52) TOP FRAME
(54) 75mm X 170mm
LINK PLATE
(55) 50mm X 170mm
LINK PLATE
(56) DOUBLE
PULLEY BLOCK
(57) LAT BAR
HOLDER
(53) GUIDE
ROD 81.8"
X 2pcs
75
76
77
80
82
83
2
2
7
4
4
7
1/2" X 4" HEX HEAD BOLT
1/2" X 3" HEX HEAD BOLT
3/8" X 1-3/4" HEX HEAD BOLT
1/2" WASHER
1/2" NYLON NUT
3/8" NYLON NUT
NO. DESCRIPTION QTY.
75 76 77
80 82 83
11
2.2 Scope of Delivery
The scope of delivery consist of the following parts. At the beginning, check whether all parts
and tools belonging to the device are included in the scope of delivery and whether damage has
occurred. In the event of complaints, the contractual partner must be contacted directly.
⚠CAUTION
If parts of the scope of delivery are missing or damaged, the assembly must not be carried out.

12 F431
2.3 Assembly
Before assembly, take a close look at the individual assembly steps shown and carry out the assembly
in the order given.
LNOTICE
+ First loosely screw all parts together and check that they t properly. Tighten the screws
using the tool only when you are instructed to do so.
+ If you have diculty recognising the graphics, we recommend that you open and/or
download the PDF instructions stored in the webshop on your end device (e.g. smartphone,
tablet or PC). There you have the option of zooming in closer. Please note that the Adobe
Acrobat Reader programme must be installed on your end device in order to open the le.
Step 1: Assembly of the Guide Rods, Base Frame and Top Frame
1. Assemble the base frame (51) to the rear stabilizer of the power rack F430 (1) with two bolts (75),
one link plate (55) and two nuts (82).
2. Attach three caps (62) to the base frame (51).
3. Insert two guide rods (53) into the holes in the base frame (51) and slide two stack spacers (61)
and two rubber donuts (65) over the top of the guide rods (53).
4. Slide the two way top plate (58) over the top of the guide rods (53).
5. Attach two rubber donuts (65) and two spring clips (73) to the two way top plate (58).
6. Assemble the top frame (52) to the guide rods (53) and to the rear top frame of power rack F430
(6) with two bolts (76), one link plate (54), four washers (80) and two nuts (82).
7. Attach four plugs (63) to the top frame (52).
8. Attach the lat bar holder (57) to the top frame (52) with two bolts (78) and two washers (81).
9. Now tighten all bolts and nuts.

61
58
65
73
65
73
65
53
75
55
82
62
62
62
1
82
61
51
65
6
82
80
54
80
82
52
63
63
63
76
80
63
78
81
57
13

FIG 6
58
FIG 1
74A
74A
74A
74A
59
52
52
64
64
83
77 83
56
77
FIG 4
FIG 2
64
77 83
FIG 3
74A
74A
52
64
77
83
FIG 5
FIG 1
FIG 2
FIG 6
FIG 3
FIG 4
FIG 5
14 F431
Step 2: Assembly of the Top Cable
LNOTICE
Assemble cables and pulleys simultaneously.
1. Route threaded end of top cable (74A) into the slot in front of the top frame (52) and out of the
slot in the rear of the top frame (52).
2. Attach the lat bar (59) to the top cable (74A).
3. Assemble two pulleys (64) to the brackets in the slots of the top frame (52) with one screw (77)
and one nut (83) each while guiding the top cable (74A) over the pulleys as shown in Fig 2 and
Fig 3.
4. Route the cable down and around the top pulley (64) of the double pulley block (56) and x the
pulley with one screw (77) and one nut (83) as shown in Fig 4.
5. Route the cable over the pulley (64) in the bracket of the top frame (52) and x it with one screw
(77) and one nut (83) as shown in Fig 5.
6. Route the cable down and screw the threaded head into the pre-assembled top cable locker of
the two way top plate (58) .

51
51
60
51
71
70
71
74
FIG 7
64
64
64
83
74
77
74
74
77
83
83
56
77 74
FIG 10
FIG 8
FIG 9
FIG 11
FIG 7
FIG 8
FIG 9
FIG 10
FIG 11
15
Step 3: Assembly of the Low Cable
LNOTICE
Assemble cables and pulleys simultaneously.
1. Assemble the low row bar (60) to the low row chain (70), snap hooks (71) and to the ball end of
the low cable (74) as shown in Fig 7.
2. Guide the low cable (74) under the two pulleys (64) on the base frame (51) and assemble the
pulleys to the brackets with one screw (77) and one nut (83) each as shown in Fig 8 and Fig 9.
3. Route the low cable (74) up and over the bottom pulley (64) in the double pulley block (56) and
x it with one screw (77) and one nut (83) as shown in Fig 10.
4. Route the low cable (74) down to the threaded frame extension and screw the threaded end
into the welded bolt on the base frame (51) as shown in Fig 11.

16 F431
3 STORAGE AND TRANSPORT
3.1 General Instructions
⚠WARNING
+ The storage location should be chosen so that improper use by third parties or children can
be prevented.
+ If your equipment does not have transportation wheels, the equipment must be
disassembled before transportation.
࣑ATTENTION
+ Make sure that the equipment is protected from moisture, dust and dirt in the selected
storage location.The storage location should be dry and well ventilated and have a constant
ambient temperature between 10°C and 35°C.

17
4 TROUBLESHOOTING, CARE AND MAINTENANCE
4.1 General Instructions
⚠WARNING
+ Do not make any improper changes to the equipment.
⚠CAUTION
+ Damaged or worn components may aect your safety and the life of the equipment.
Therefore, immediately replace damaged or worn components. In such a case, contact the
contract partner. The equipment must not be used until it has been repaired. If necessary,
use only original spare parts.
࣑ATTENTION
+ In addition to the instructions and recommendations for maintenance and care given here,
additional service and/or repair work may be necessary; this must only be carried out by
authorised service technicians.
4.2 Faults and Fault Diagnosis
The equipment undergoes regular quality controls during production. Nevertheless, faults or
malfunctions may occur. Frequently, individual parts are responsible for these disturbances, an
exchange is usually sucient. Please refer to the following overview for the most common errors and
how to correct them. If the equipment still does not function properly, contact your contract partner.
Fault Cause Solution
Grinding noises Cables or pulleys do not run
smoothly or are damaged
+ Visual inspection of the cable routing
or the pulley guide
+ If damaged, replace the defective
part
Weight hanging in
the air Cable tensioned too tight Readjust cable tension
Cable without tension Cable too loose + Check cable routing
+ Readjust cable tension
Squeaking & cracking
noises
Screw connections loosened
or too tight
+ Check or lubricate screw
connections*
+ Check cable routing
Unit wobbles + Uneven ground
+ Loose screw connections
+ Align unit
+ Tighten screw connections
Heavy draught
+ Weight holders/guide
rods too dry
+ Faulty cable routing
+ Lubricate guide rods*
+ Check cable routing
* With a grease-free silicone oil or silicone spray.

18 F431
4.3 Maintenance and Inspection Calendar
To avoid damage from body sweat, the equipment must be cleaned with a damp towel (no solvents!)
after each training session.
The following routine tasks must be performed at the specied intervals:
Part Weekly Monthly Quarterly
Cables C I
Screw connections I
Pulleys and cable routing I
Slide rails/Guide rods I
Legend: C = clean; I = inspect
5 DISPOSAL
At the end of its operational life, this equipment cannot be disposed of in normal household waste.
Instead, it must be disposed of via an recycling centre. Further information can be obtained from
your local authority‘s recycling service.
The materials can be recycled as per their symbols. Through the reuse, recycling
of materials or other forms of recovery of old equipment, you make an important
contribution to the protection of the environment.

19
oor mat
chest strap
weight block extension
triceps rope
6 RECOMMENDED ACCESSORIES
To make your training experience even more ecient and pleasant, we recommend that you add
suiting accessories to your tness equipment. For training equipment like smith machines, weight
benches or racks this could for example be a oor mat, which makes your tness equipment stand
moresecurely andalsoprotects the oor fromsweat butitcould be also additional weights,handles,
foot straps for leg exercises or triceps ropes. For some smith machines, there are also optional add-
ons such as leg presses that make your workout even more intense and comprehensive.
Our range of accessories oers the highest quality and makes training even
better. If you would like to nd out more about compatible accessories, please go
to the detail page of the product in our webshop (the easiest way is to enter the
article number in the search eld above) and go to the recommended accessories
on this page. Alternatively, you can use the QR code provided. Of course, you can
also contact our customer service: by telephone, e-mail, in one of our branches
or via our social media channels. We will be happy to advise you!