Body Solid GPR370.1 User manual

BODY-SOLID,Inc.
1900 S. Des Plaines Ave.
Forest Park, IL 60130 USA
Phone:[phone]
Fax:[phone]
www.bodysolid.com
OWNER'S MANUAL
GPR370.1

TABLE OF CONTENTS
General Instructions ..…………………….………..……..….……..2
Training Tips and Safety Information ..….……..………….……..3
Inspection and Maintenance Schedule ………..………….……..4
Hardware Illustration .…………………………..……..…………….5-6
Parts Illustration ……….……………………….…………..………..7
Assembly（Step 1）…………………..……………………………..8-9
Page 1
GPR370 ASSEMBLY INSTRUCTIONS
GPR370.1
-
05200
7

GENERAL INSTRUCTIONS
Thank you for purchasing the Body-Solid equipment. At Body-solid, our
goal is to ensure customer satisfaction. If you have any questions about
these instructions or have any problems with assembly or parts for this
machine, please call our Customer Service Department at 1-800-556-
3113.
Prior to assembling any Body-Solid machine, please take the time to read
the instructions thoroughly. Please use this manual to make sure that all
parts have been included with your shipment. When ordering
replacement parts, please refer to the part number and description of
each part from this manual. Use only Body-Solid replacement parts when
servicing any Body-Solid machine. Failure to do so may void your
warranty and could result in personal injury.
Body-Solid equipment is designed to provide the safest, smoothest and
most effective workouts possible. After you have finished assembling this
product, check all stations to ensure correct operation. If for some reason
you experience problems with any functions of this machine, do not
continue operation. First, re-check all of the assembly instructions to
locate any possible errors made during assembly. If you are not able to
correct the problem, contact our Customer Service Department
immediately at 1-800-556-3113.
TOOLS REQUIRED
‧Socket Wrench
‧1/2" Sockets
‧Crescent Wrench
‧ Rubber Mallet
‧Tape Measure
Page 2
GPR370
ASSEMBLY INSTRUCTIONS
GPR370.1
-
05200
7

TRAINING TIPS AND SAFETY INFORMATION
Before starting any exercise program, it is recommended that you consult
your physician and get a complete physical examination. There is a risk
assumed by individuals who use this type of equipment. To minimize risk,
follow the rules below.
‧ Always consult your physician before starting any exercise program.
‧ Do not allow children or minors to play on or around the equipment.
‧ Warm up properly before engaging in any weight training regimen.
‧ Before using, read all the warning labels and instructions on the use of this
machine.
‧ Do not modify the machine in any way.
‧ Inspect the machine before use for any damaged, worn or missing parts. If
there is any doubt about the ability of this equipment to operate safely, do not
use the equipment until it is serviced.
‧ Exercise with care, performing exercises at a smooth, moderate pace. Never
perform jerky or uncoordinated movements that may result in injury.
‧ Never hold your breath while exercising.
‧ Learn how to perform the exercise correctly before using heavy weight.
Correct form is important to avoid injury and to ensure that you work the
proper muscle groups.
‧ It is recommended that you train with a training partner.
‧ Keep body and clothing clear of cables and moving parts when the machine
is in use.
‧ Know your limitations. If you are new to resistance training or are starting an
exercise routine after a prolonged lay-off, start slowly and build up to a more
intense routine.
Failure to follow these rules may result in serious injury. If unsure about
the proper use of the machine, consult your local Body-Solid distributor or
call the Body-Solid Customer Service department at 1-800-556-3113.
Page 3
GPR370
ASSEMBLY INSTRUCTIONS
GPR370.1-052007

INSPECTIONS AND MAINTENANCE SCHEDULE
There is a risk assumed by individuals who use this type of equipment. To
minimize risk, follow the rules below.
‧ Inspect equipment daily, ensuring that all nuts, bolts and screws are fully
tightened.
‧ Inspect cables daily ensuring they are routed properly and not worn, frayed or
stretched. Check and adjust tension on cables daily.
‧ When using pop-pin adjustments, always make sure the plunger for the pop-
pin is securely inserted into an adjustment hole.
‧ Before performing any exercise, always make sure all ball-pins, ring-pins,
pop-pins and selector pins are inserted properly and all snap-links are
properly closed.
‧ Replace worn parts immediately.
‧ Human perspiration is corrosive. Clean your machine regularly. Wipe down
and dry upholstery and frame pieces on a daily basis.
‧ Every week clean the chrome guide rods with a dry cloth and apply a coat of
dry silicon spray or Teflon based spray lubricant.
‧ Every week clean and lubricate all non-chrome guide rods and all seat posts
and adjustments for starting positions.
‧ Every week check hand grips, rollers and non-skid surfaces for wear.
‧ Only use Body-Solid parts. Parts form other manufacturers or any other
modifications will void the warranty and may result in serious injury.
‧ Do not use this machine with damaged, worn or missing parts.
‧ If there is any doubt about the ability of this equipment to operate safely, do
not use the equipment until it is serviced.
‧ Please ensure that all warning stickers are visible and acknowledged by
users of the equipment.
Failure to follow these rules may result in serious injury. If unsure about
the proper use of the machine, consult your local Body-Solid distributor or
call the Body-Solid Customer Service department at 1-800-556-3113.
Page 4
GPR370
ASSEMBLY INSTRUCTIONS
G
PR370
.1
-
05200
7

ASSEMBLY INSTRUCTIONS
Page
GPR370
GPR370.1-052007 5
2
13456
HARDWARE ILLUSTRATION
A1. HEX BOLT M12X25L PARTIAL THREAD QTY.2
A2. HEX BOLT M12X70L PARTIAL THREAD QTY.4
A3. HEX BOLT M12X80L PARTIAL THREAD QTY.12
A4. HEX BOLT M12X75L PARTIAL THREAD QTY.6
B1. M12 NYLON LOCK NUT QTY.18
C1. M12 (I.D) FLAT WASHER (O.D)n34 QTY.40

ASSEMBLY INSTRUCTIONS
Page
GPR370.1-052007 6
D1. 50X75 END CAP (9211-084) ----------------------------------------- [2PCS]
D2. 38X325 RUBBER BAR CATCH (9310-042) ---------------------- [2PCS]
D3. 2"X2" FOOT CAP (9212-018) ---------------------------------------- [2PCS]
D4. n49.5 RUBBER END CAP (9211-074) ---------------------------- [4PCS]
D5. 45X45 TAPE (9440-067) ---------------------------------------------- [4PCS]
D6. 45X70 TAPE (9440-068) ---------------------------------------------- [2PCS]
D1 D2 D3
D4 D5 D6
HARDWARE ILLUSTRATION
GPR370

ASSEMBLY INSTRUCTIONS
Page
GPR370.1-052007 7
A [2PCS]
B [2PCS]
C [2PCS]
E [1PCS]
F [1PCS]
D [1PCS] G [4PCS]
H [4PCS]
I [1PCS]
J [1PCS]
(8312-091)
(8343-056)
(8343-056)
PARTS ILLUSTRATION SHEET
GPR370

ASSEMBLY- STEP 1
**Note ： Do Not fully tighten frame bolts and nuts until after completing Step 1
The following Parts and Hardware will be needed to complete Step 1
Parts Description Hardware Description
Qty Part Part Description Qty Part Part Description
2 A Base Frame 2 A1 M12X25 hex head bolt
2 B Side Frame 4 A2 M12X70 hex head bolt
2 C Upright Frame 12 A3 M12X80 hex head bolt
1 D Cross Support 6 A4 M12X75 hex head bolt
1 E Left Safety 18 B1 M12 Nylon Lock Nut
1 F Right Safety 40 C1
M12 (I.D) Washer Ø34
4 G Weight Horns 2 D1 50x75 End Cap
4 H Support Plates 2 D2 38x325 Rubber Bar Catch
1 I Lift Off Frame 2 D3 2"x2" Foot Cap
1 J Lift Off Frame 4 D4
Ø49.5 Round End Cap
4 D5 45x45 Tape
2 D6 45x70 Tape
Step by Step
1. Attach 2 (A) - Base Frame to 2 (B) - Side Frames
2. Attach (D) - Cross Support and 2 (G) - Weight Horns to 2 (B) - Side Frame
3. Attach (A) - Back Frame and (J) - Back Support Plate to (B) - Middle Frame
4. Attach 4 (G) - Weight Horns and 4 (H) - Support Plates to 2 (B) - Side Frames
5. Attach (I) - Lift Off Frame and (J) - Lift Off Frame to 2 (C) - Upright Frames
**Securely Tighten All Frame Bolts Used in Steps 1
GP
R
370
ASSEMBLY INSTRUCTIONS
G
PR370
.1
-
05200
7
Page 8

ASSEMBLY INSTRUCTIONS
Page
GPR370.1-052007 9
I
D5X2
D6X2
D5X2
D2X2
D3X2
C1X6
A4X6
D1X2
J
HX2
AX2
D4X4
BX2
HX2
A1X2 A3X8
C1X16
B1X8
A2X4
C1X4
B1X4
C1X4
A3X4
C1X4
B1X6C1X6
CX2
E
F
D
GX4
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK, YOU MUST FOLLOW THESE RULES:
1. Inspect equipment before each workout. Checke that all nuts, bolts, screws and pop pins are
in place and fully tightened. Also,before use,check cables for signs of wear. Replace all worn
parts immediately. Never use machine if any parts are damaged or missing. Failure to follow
these rules may result in serious injury.
2. Keep clear of the cables and all moving parts when the machine is in use.
3. Always make sure all Snap Links are closed when doing any cable/pulley exercises.
4. Exercise with care. Perform your exercises at a smooth moderate pace; never perform jerky
or uncoordinated movements that may cause injury.
5. It is recommended that you should workout with a training partner.
6. Do not allow children or minors to play on or around this equipment.
7. If unsure of proper use of equipment, call your local Body-Solid distributor or the Body-Solid
customer service department at 1-800-556-3113.
8. WARNING: Consult your physician before starting your exercise program. For your own safety.
do not begin any exercise program without proper instruction.
RAL2-11-98
ASSEMBLY STEP 1
GPR370