Bosch D7412GV2 Quick start guide

EN
Operation and Installation Guide
Control Panels
D9412GV2
/
D7412GV2

D9412GV2/D7412GV2 | Operation and Installation Guide | Trademarks
2 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
Trademarks
CoBox is a registered trademark of Lantronix.
Windows is a registered trademark of Microsoft
Corporation in the United States or in other countries.
Molex is a registered trademark of Molex
Incorporated.
Certifications and Approvals
The D9412GV2/D7412GV2 Literature Pack includes
the D9412GV2/D7412GV2 Approved Applications
Compliance Guide (P/N: F01U003639). Refer to this
guide for additional guidelines on installing the control
panels in Underwriters Laboratories Inc. (UL) and fire-
specific applications.
Listings and Approvals
UL
The D9412GV2 and D7412GV2 Control Panels are
UL Listed for Central Station, Local, Auxiliary,
Proprietary, and Household Fire Alarm, and Central
Station, Local, Police Station Connect, Household
Burglar Alarm and Encrypted line Security when
communicating via a network.
Department of Defense (DOD)
The D9412GV2/D7412GV2 was granted approval for
Department of Defense (DoD) installations in
Sensitive Compartmented Information Facilities
(SCIF).
Federal Communications
Commission (FCC) Rules
Part 15
This equipment was tested and found to comply with
the limits for a Class A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy; and if not installed and used
according to the instructions, can cause harmful
interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user is required to correct the interference at his or
her own expense.
Part 68
This equipment complies with Part 68 of FCC rules. A
label contains, among other information, the FCC
registration number and ringer equivalence number
(REN). If requested, this information must be provided
to the telephone company.
The D9412GV2 and D7412GV2 Control Panels are
registered for connection to the public telephone
network using an RJ38X or RJ31X jack.
The REN is used to determine the number of devices
that can be connected to the telephone line.
Excessive RENs on the telephone line may result in
the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the RENs
should not exceed five. To be certain of the number of
devices that may be connected to the line, as
determined by the RENs, contact the telephone
company to determine the maximum REN for the
calling area.
If you experience trouble with the D9412GV2 or
D7412GV2 Control Panel, please contact Bosch
Security Systems Customer Service for repair and
warranty information. If the trouble is causing harm to
the telephone network, the telephone company might
request that the equipment be removed from the
network until the problem is resolved. User repairs
must not be made, and doing so will void the user’s
warranty.

D9412GV2/D7412GV2 |Operation and Installation Guide | Federal Communications Commission (FCC) Rules
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 3
If the D9412GV2 or D7412GV2 Control Panel causes
harm to the telephone network, the telephone
company attempts to notify you in advance. If
advance notice is not practical, the telephone
company notifies you as soon as possible. Also, you
will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
The telephone company might make changes in its
facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this
happens, the telephone company provides advance
notice in order for the necessary modifications to be
made in order to maintain uninterrupted service.
This equipment cannot be used on public coin service
provided by the telephone company. Connection to
Party Line service is subject to state tariffs. (Contact
your state public utilities commission for information.)
FCC Registration Number: AJ9MUL-46532-AL-E
Service Center in USA:
Bosch ST Service Center
8601 East Cornhusker Hwy
Dock B
Lincoln, NE 68507 - 9702 USA
Ringer Equivalence: 0.4B

D9412GV2/D7412GV2 | Operation and Installation Guide | Contents
4 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
Contents
1.0 Introduction..................................................7
2.0 Lightning Strikes .........................................8
2.1 Effects............................................................8
2.2 Precautions during Installation ......................8
3.0 Overview.......................................................9
3.1 Configuration and Parts.................................9
3.1.1 Parts List......................................................10
3.1.2 Parts Available by Separate Order..............10
3.2 Accessories .................................................10
3.3 Features in the D9412GV2 and D7412GV211
3.3.1 SDI Molex Connector ..................................11
3.3.2 Tip and Ring Posts ......................................11
3.3.3 Super Capacitor...........................................11
3.3.4 Telephone Line Sniff....................................12
3.3.5 Points...........................................................12
3.3.6 Areas and Accounts ....................................12
3.3.7 Digital Communicator ..................................12
3.3.8 Keypads.......................................................13
3.3.9 Keyswitch ....................................................13
3.3.10 Access Control ............................................13
3.3.11 Event Memory .............................................13
3.3.12 Event Log ....................................................14
3.3.13 Ground Fault Detection ...............................14
3.3.14 Ground Fault Detection Added Feature ......14
3.3.15 Conettix Functions.......................................14
3.3.16 Programming ...............................................14
3.3.17 Other Features ............................................14
4.0 Installation..................................................15
4.1 Installation Preparation................................15
4.2 Enclosure Options .......................................15
4.3 Mounting Enclosure.....................................15
4.4 Installing the Control Panel..........................16
4.5 Connecting Earth Ground............................16
4.5.1 Terminal 10..................................................16
4.5.2 Ground Fault Detect Enable ........................16
4.5.3 Enabling Ground Fault Detection ................17
4.5.4 D7212GV2 Ground Fault Specifications .....17
4.5.5 Locking the Reset Pin..................................18
4.6 Completing the Installation ..........................18
4.6.1 Charging the Battery....................................18
4.6.2 Installing and Wiring Detection Devices......18
4.6.3 Installing Modules and Relays.....................19
4.6.4 Connecting the On-board Points and
Keypads.......................................................19
4.6.5 Powering Up ................................................19
4.7 Programming the Control Panel ..................19
4.8 Installing the Point Chart Label................... 19
4.9 Testing the System ..................................... 19
4.10 Service Walk Test ....................................... 20
5.0 Power Supply ............................................ 23
5.1 Primary Power Terminals 1 and 2 .............. 23
5.1.1 Primary (AC) Power Circuit......................... 23
5.1.2 Installing the Transformer ........................... 23
5.2 Secondary Power Terminals....................... 23
5.2.1 Secondary (DC) Power ............................... 23
5.2.2 Installing the Battery ................................... 24
5.2.3 Replacing the Battery.................................. 26
5.2.4 Battery Supervision..................................... 26
5.2.5 Battery Charging Circuit.............................. 26
5.2.6 Battery Discharge and Recharge Schedule 27
6.0 Power Outputs........................................... 28
6.1 Circuit Protection......................................... 28
6.2 Total Available Power ................................. 28
6.3 Continuous Power Output Terminals 3, 8,
24, and 32 ................................................... 28
6.4 Programmable Power Output Terminals 6,
7, and 8 ....................................................... 28
6.4.1 Programming............................................... 28
6.4.2 Terminals 6 and 7 ....................................... 29
6.4.3 Fire System Power Formula ....................... 29
6.4.4 Terminal 8 ................................................... 29
7.0 Telephone Connections ........................... 30
7.1 Registration................................................. 30
7.2 Notification .................................................. 30
7.3 Location....................................................... 30
7.4 Telephone Cord Connection....................... 30
7.5 Phone LED (Red)........................................ 31
7.6 Operation Monitor LED (Green).................. 31
7.7 Dialing Format............................................. 31
7.8 Telephone Line Monitor .............................. 31
7.9 Called Party Disconnect.............................. 31
7.10 Communication Failure ............................... 31
7.11 D928 Dual Phone Line Switcher................. 32
7.11.1 Description .................................................. 32
7.11.2 Operation .................................................... 32
7.11.3 Installing the D928 ...................................... 33
7.11.4 D928 Status LEDs ...................................... 33
8.0 On-Board Points ....................................... 35
8.1 Terminals 11 to 22 Description ................... 35
8.2 Point Sensor Loops..................................... 35
8.3 Point Parameters ........................................ 35
8.4 Point Response Time.................................. 36

D9412GV2/D7412GV2 |Operation and Installation Guide | Contents
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 5
8.5 Wiring Information for Installations Using
the Rothenbuhler 5110/4001-42 High
Security Bell.................................................36
9.0 Off-Board Points........................................39
9.1 Point (Zonex) Bus: D9412GV2 Terminals
and D7412GV2 Terminals...........................39
9.1.1 POPIT Modules ...........................................39
9.1.2 POPEX Modules..........................................39
9.1.3 Missing Conditions ......................................39
9.1.4 Extra Point Events .......................................39
9.1.5 D9412GV2/D7412GV2 Responses to
Missing Point Conditions .............................40
9.2 D8125, D8127 and D9127 POPIT Modules 40
9.3 Installing the D8125 POPEX Module ..........43
9.3.1 Mounting......................................................43
9.3.2 Wiring the D8125 to the Control Panel........43
9.3.3 Wiring POPITs to the Data Expansion
Loop.............................................................43
9.3.4 Wiring Data Expansion Loops to POPEX
Modules .......................................................44
9.3.5 POPIT Sensor Loops...................................44
9.3.6 POPIT Module Point Assignments ..............44
9.3.7 Program Record Sheet................................44
9.3.8 POPIT Labels ..............................................45
9.4 D8128D OctoPOPIT Module .......................45
9.4.1 Description...................................................45
9.4.2 Listings.........................................................46
9.4.3 Installation ...................................................47
9.4.4 Setting the OctoPOPIT Switches ................47
9.4.5 Mounting OctoPOPITs.................................48
9.4.6 Wiring OctoPOPITs .....................................48
9.4.7 OctoPOPIT Sensor Loops...........................51
9.5 Testing Off-Board Points .............................52
10.0 Off-Board Relays .......................................53
10.1 D8129 OctoRelay ........................................53
10.1.1 Configuring the D8129 OctoRelay...............54
10.1.2 Relay Outputs..............................................54
10.1.3 Installation ...................................................54
10.1.4 Wiring Connections .....................................55
10.2 D811 Arm Status Relay Module ..................55
10.2.1 Relay Output................................................55
10.2.2 Installation ...................................................56
10.2.3 Wiring Connections .....................................56
11.0 Arming Devices .........................................58
11.1 Description...................................................58
11.2 Keypad Terminals 29 to 32 .........................58
11.2.1 Assigning an Address for the Keypad .........58
11.2.2 Installation ...................................................59
11.3 D279A Independent Zone Control .............. 60
11.4 Keyswitch .................................................... 60
11.4.1 Description .................................................. 60
11.4.2 Programming............................................... 60
11.4.3 Installation ................................................... 60
11.4.4 Operation .................................................... 60
12.0 SDI Devices................................................ 62
12.1 Description .................................................. 62
12.2 Installation ................................................... 62
12.3 D9131A Parallel Printer Interface Module .. 62
12.3.1 Switch Settings............................................ 62
12.3.2 Supervision ................................................. 62
12.4 D9210B Wiegand Control Interface
Module ........................................................ 63
12.4.1 Access......................................................... 63
12.4.2 Switch Settings............................................ 63
12.5 SDI Address 80 ........................................... 63
12.5.1 Serial Interface Modules (SIMs).................. 63
12.5.2 Address Settings......................................... 63
12.5.3 Supervision ................................................. 64
12.6 SDI Address 88 ........................................... 64
12.6.1 D9133DC Direct Connect Programming
Module ........................................................ 64
12.6.2 Network Interface Modules ......................... 64
12.6.3 Address Settings......................................... 65
12.6.4 Supervision ................................................. 65
13.0 Programmer and Accessory
Connections .............................................. 66
13.1 Programmer Connector .............................. 66
13.2 Programmer Access Reports...................... 66
13.3 Accessory Connector.................................. 66
14.0 Faceplates.................................................. 67
14.1 D9412GV2 Faceplate ................................. 67
14.2 D7412GV2 Faceplate ................................. 68
Appendix A: System Wiring Diagrams, Issue A . 69
A.1 D9412GV2 Control Panel ........................... 69
A.2 D7412GV2 Control Panel ........................... 72
Appendix B: Point Address Charts...................... 75
B.1 Zonex 1, Points 9 to 127 (D9412GV2);
Zonex 1, Points 9 to 75 (D7412GV2).......... 75
B.2 Zonex 2, Points 129 to 247 (D9412GV2
Only)............................................................ 76
Specifications......................................................... 77

D9412GV2/D7412GV2 | Operation and Installation Guide | Contents
6 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
Figures
Figure 1: System Configuration..............................9
Figure 2: Enclosure Mounting ..............................15
Figure 3: Ground Fault Detection.........................16
Figure 4: Ground Fault Detect (S4)......................17
Figure 5: Area 5 Silent Alarm Relay in RPS.........17
Figure 6: Reset Pin...............................................18
Figure 7: D9412GV2 Service Walk Test Flow
Chart .....................................................21
Figure 8: D7412GV2 Service Walk Test Flow
Chart .....................................................22
Figure 9: Non-Power-Limited Wiring ....................25
Figure 10: Charging and Battery LEDs ..................26
Figure 11: RJ31X Wiring ........................................30
Figure 12: Phone Connector, Phone LED, and
Operation Monitor LED Locations.........30
Figure 13: D928 Dual Phone Line Switcher...........33
Figure 14: On-board Point Sensor Loop Wiring.....35
Figure 15: Rothenbuhler 5110/4001-42 High
Security Bell Wiring Configuration ........37
Figure 16: Wiring the Rothenbuhler 5110/4001-42
High Security Bell to the D9412GV2
or D7412GV2 Control Panel .................38
Figure 17: Connecting the D8125 POPEX to the
D9412GV2 Control Panel .....................41
Figure 18: Connecting the D8125 POPEX to the
D7412GV2 Control Panel .....................42
Figure 19: Program Record Sheet .........................45
Figure 20: D8128D OctoPOPIT Layout..................46
Figure 21: Connecting D8128D OctoPOPITs to
the D9412GV2 ......................................49
Figure 22: Connecting D8128D OctoPOPITs to
the D7412GV2 ......................................50
Figure 23: Wiring Multiple D8128Ds Using
Molex®Connectors ...............................51
Figure 24: D8128D OctoPOPIT Sensor Loops ......52
Figure 25: D8129 Connections to the D9412GV2 .53
Figure 26: D8129 Connections to the D7412GV2 .54
Figure 27: D811 Module Wiring to the
D9412GV2 ............................................56
Figure 28: D811 Module Wiring to the
D7412GV2 ............................................57
Figure 29: Power at Keypads.................................60
Figure 30: Keyswitch Wiring...................................61
Figure 31: D9133 Jumper Setting for Address 80..64
Figure 32: DX4010i DIP Switch Settings................64
Figure 33: DX4020 DIP Switch Settings ................65
Figure 34: Reset Pin...............................................66
Figure 35: Programmer and Accessory
Connections.......................................... 66
Figure 36: D9412GV2 Faceplate........................... 67
Figure 37: D7412GV2 Faceplate........................... 68
Figure 38: D9412GV2, Power Supply Side ........... 69
Figure 39: D9412GV2, Input Points and
Peripheral Devices ............................... 70
Figure 40: D9412GV2, SDI Devices...................... 71
Figure 41: D7412GV2, Power Supply Side ........... 72
Figure 42: D7412GV2, Input Points and
Peripheral Devices ............................... 73
Figure 43: D7412GV2, SDI Devices...................... 74
Tables
Table 1: Related Documentation.......................... 7
Table 2: GV2 Series Control Panel Differences... 9
Table 3: Compatible Accessories....................... 10
Table 4: Software Version Compatibility of
D6500 MPU and Line Cards ................ 13
Table 5: Compatible Keypads and Command
Centers ................................................. 13
Table 6: Ground Fault Impedance
Specifications ....................................... 17
Table 7: Battery Discharge and Recharge
Schedule............................................... 27
Table 8: Charging Status and Low Battery
LEDs..................................................... 27
Table 9: Phone Cord Lengths............................. 33
Table 10: Point Parameters.................................. 35
Table 11: POPEX Modules................................... 39
Table 12: Extra Point Events................................ 39
Table 13: Off-Board Point Errors.......................... 40
Table 14: Data Expansion Loop Wire
Specifications ....................................... 43
Table 15: D8128D OctoPOPIT Switch Settings
for D9412GV2 and D7412GV2............. 47
Table 16: Switch 5 Settings for Line Termination. 47
Table 17: Terminal Strip Connections .................. 48
Table 18: D8129 OctoRelay Switch Settings ....... 54
Table 19: Number of D8128Ds Used with D8129s
.............................................................. 55
Table 20: Keypad Address Settings ..................... 58
Table 21: Keypad Connections ............................ 59
Table 22: SDI Device Connections ...................... 62
Table 23: Printer Address Switch Settings ........... 62
Table 24: Address Switch Settings for Access
Control Module ..................................... 63
Table 25: Zonex 1 Point Address Chart ............... 75
Table 26: Zonex 2 Point Address Chart ............... 76
Table 27: Specifications ....................................... 77

D9412GV2/D7412GV2 |Operation and Installation Guide | 1.0 Introduction
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 7
1.0 Introduction
This manual addresses the operation and installation of the D9412GV2 and D7412GV2 Control Panels.
Throughout this guide, the words “control panel” refer to both control panels (D9412GV2 and D7412GV2).
Table 2 on page 9 provides an overview of the differences in the control panels.
To obtain any of the documents in Table 1, contact Bosch Security Systems, inc. Technical
Support and request the documentation by its corresponding part number.
Table 1: Related Documentation
Product Type Name of Documentation∗Part Number
D9412GV2/D7412GV2 Release Notes∗F01U003637
D9412GV2/D7412GV2 Approved Applications Compliance Guide∗F01U003639
D9412GV2/D7412GV2 Troubleshooting Guide∗F01U011024
D9412GV2/D7412GV2 Operation and Installation Guide (this document) ∗F01U003641
D9412GV2/D7412GV2 Program Entry Guide∗F01U003636
D9412GV2/D7412GV2 Program Record Sheet∗F01U003635
UL Certificated Bank Safe and Vault Applications Technogram 73-07302-000
Control Panels
9000/G/GV2 Series Technical Service Note: UL Smoke Detector Compatibility∗33284
D1255RB/D1256RB/D1257RB Installation Instructions∗F01U011791
D1255/D1255B Installation Instructions 74-06819-000
D1256/D1257 Installation Instructions 74-06925-000
D1260/D1260B Installation Guide 48101
D1260/D1260B Owner’s Manual 50410
D720 Series Installation Instructions 74-06918-000
D279A Operation and Installation Instructions 46458
Security System Owner's Manual 71-06633-000
Keypads
GV2 Series Owner's Manual Supplement F01U063791
RPS Installation and Operation Guide 4998141259 Programming
Tools D5200 Operation Manual 74-06176-000
D8128D Installation Guide∗41323
D8125MUX Operation & Installation Guide∗36796
Expansion
Devices
D9210B Operation and Installation Guide∗32206
∗These products meet the requirements for UL 864 Commercial Fire applications..

D9412GV2/D7412GV2 |Operation and Installation Guide | 2.0 Lightning Strikes
8 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
2.0 Lightning Strikes
The control panels are designed to significantly
reduce electromagnetic interference and malfunction
generally caused by lightning.
2.1 Effects
Any electronic system can be struck directly by
lightning or be adversely affected by a lightning strike
near the system. When lightning strikes, several
things happen:
•An electromagnetic wave spreads from the point
of the strike inducing high voltages in nearby
conductors.
•The voltage changes substantially on electrical
grounds near the lightning strike.
•High voltages are induced upon anything directly
struck by lightning.
Symptoms of installations that lightning might strike or
affect are Missing Trouble, Missing Alarm, or Point
Bus Trouble events. Occasionally, Reboot and
Watchdog events might be sent because the control
panel tried to reset itself.
Electronic systems, including control panels, cannot
be completely immune to direct or indirect lightning
strikes; however, some proven installation practices
might greatly reduce the risk of undesirable affects.
2.2 Precautions during Installation
To minimize the risk of undesirable effects from
lightning strikes on high risk installations that use a
point-bus technology:
•Do not run wiring outside the building.
•If you must install the unit in a metal building,
keep the wiring at least 0.61 m (2 ft) away from
external metal surfaces.
•Earth ground the unit correctly. Do not use an
electrical ground or telephone ground.
•Avoid running wires near telephone, data, or
power lines inside a building. Historical evidence
shows that locating control panel wiring at least
0.61 m (2 ft) away from telephone, data, or power
lines is successful at minimizing lightning
damage. When your data lines must cross the
path of AC or other wiring, cross the lines
perpendicularly.

D9412GV2/D7412GV2 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 9
3.0 Overview
3.1 Configuration and Parts
Figure 1: System Configuration
Use keypads or keyswitches to arm the control
panel by area. Each control panel can have up to eight
areas. Each area can have its own account number or
areas can be grouped together with a common account
number. Points of protection are assigned to areas.
Control
Panel
On-B oard Points
1 to 8
D9131A Module connects
to a parallel printer to print
the event log.
D928 Module allows the control
panel to monitor two phone lines.
Each D8128D OctoPOPIT combines
eight POPIT points in one module.
D8132 Modules (two 12 VDC batteries)
provide additional power for keypads and
other powered devices.
D8129 OctoRelay provides alarm
and auxiliary relay output.
(Other functions available.)
D9210B Modules can be
used for access control.
DX4020 allows communciation
over a Local or Wide Area Network
(LAN/WAN).
D8125, ISW-D8125CW,
D8125INV, or
D8125MUX Interface
used for point expansion.
Table 2: GV2 Series Control Panel Differences
Features D9412GV2 D7412GV2 D7212GV2
Access Control Yes - 8 doors Yes - 2 doors No
Arm/Disarm Passcodes 249 99 99
Cards/Tokens 996 396 N/A
Passcode-Protected
Custom Functions 16 4 4
Number of Printers 3 1 1
Number of Points 246 75 40
Number of Relays 128 64 24
Number of Areas 8 8 4

D9412GV2/D7412GV2 |Operation and Installation Guide | 3.0 Overview
10 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
3.1.1 Parts List
The D9412GV2 andD7412GV2 Control Panels are
shipped assembled from the factory with the following
parts:
Literature Pack
•D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635)
•9000/G/GV2 Series Technical Service Note: UL
Smoke Detector Compatibility (P/N: 33284)
•7000/9000 Series Point Chart Label
(P/N: 79-06660-000)
Assembly
•PC board
•Faceplate shield
•Mounting skirt
•One #6 x 1/4-in. screw
3.1.2 Parts Available by Separate Order
Order the following components separately to
complete a basic eight-point installation.
The D1260 and D1260B Keypads must
have firmware version 1.03 or higher for
use with the D9412GV2 and D7412GV2.
•D1255B, D1255, D1256, D1260, D1260B
Keypad, or D720 Keypad
•D1255RB Fire Keypad, D1256RB Fire Keypad, or
D1257RB Fire Alarm Annunciator
•D1640 Transformer
•D126 or D1218 Battery
•D161 or D162 Phone Cord (order two cords if
using the D928 Dual Phone Switcher)
•D8103, D8108A, or D8109 Enclosure
Configured packages are also available. Please
consult the Bosch Security Systems, Inc. Product
Catalog.
The following literature is available in a separate
literature package for dealers.
•D9412GV2/D7412GV2 Operation and Installation
Guide (P/N: F01U003641)
•D9412GV2/D7412GV2 Approved Applications
Compliance Guide (P/N: F01U003639)
•D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636)
• D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635)
The D9412GV2/D7412GV2 Troubleshooting Guide is
available in hard copy only (P/N: F01U011024),
CD-ROM only (P/N: F01U012325), or hard copy with
enclosed CD-ROM (P/N: F01U012326).
3.2 Accessories
Refer to the Bosch Security Systems, Inc. product catalog for additional information.
Table 3: Compatible Accessories3
Model Title UL 864 Fire Intrusion
D122/D122L Dual Battery Harness X X X
D125B Powered Loop Interface Module X X X
D127 Reversing Relay X X X
D129 Dual Class A Initiation Circuit Module X X X
D130 Relay Module X X X
D185 Reverse Polarity Module X X
D192G Bell Circuit Supervision Module X X X
D279A Independent Zone Control (On-Board and OctoPOPIT
Points)
X
D720 Keypad (Area LED) X X
D720R LED Keypad (red) X X
D720W LED Keypad (white) X X
D928 Dual Phone Line Switcher X X X
D1255RB Fire Keypad X X X
D1256RB Fire Keypad X X X
D1257RB Fire Alarm Annunciator X X X
D1218 12 V, 17.2 Ah Rechargeable Battery X X X
D1255/D1255B Keypads (General Purpose) X X
D1255R Text Keypad (red) X X

D9412GV2/D7412GV2 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 11
Table 3: Compatible Accessories (continued)3
Model Title UL 864 Fire Intrusion
D1255W Text Keypad (white) X X
D1256 Fire Keypad (Command Center) X
D1257 Fire Alarm Annunciator X
D1260/D1260B1Keypads X X
D1640 16.5 VAC 40 VA Transformer X X X
D8004 Transformer Enclosure X X X
D8125 POPEX Module X X X
D8125MUX Multiplex Bus Interface X X X
ISW-D8125CW2Commercial Wireless Interface Module X2
D8125INV2Inovonics Wireless Interface Module X2
D8128D OctoPOPIT Module X X X
D8129 OctoRelay Module X X X
D8130 Release Module X X X
D8132 Battery Charger Module X X
D9127U/T POPIT Module X X X
D9131A Parallel Printer Interface Module X X
D9210B Access Control Interface Module X X X
ZX776Z PIR Motion Sensor [15 m (50 ft)] with POPIT X
ZX794Z PIR Motion Sensor [24 m (80 ft)] with POPIT X
ZX865 PIR/Microwave Motion Sensor [+1.7°C (+35°F)] with POPIT X
ZX938Z PIR Motion Sensor [18 m (60 ft)] with POPIT X
ZX970 PIR/Microwave Motion Sensor [+1.7°C (+35°F)] with POPIT
1Version 1.03 or above
2The ISW-D8125CW and the D8125INV were not investigated by UL. Do not use the ISW-D8125CW or D8125INV in UL Listed
installations.
3Where the fire alarm transmitter is sharing on-premise communications equipment, the shared equipment must be UL Listed (ITE
or fire protective signaling).
3.3 Features in the D9412GV2 and
D7412GV2
3.3.1 SDI Molex Connector
Use the SDI Molex Connector to connect easily an
SDI device with the SDI bus, without needing to
disconnect wires connected to the SDI terminals.
Possible applications include:
•Connecting a DX4010i to program the control
panel with Remote Programming Software (RPS)
at the premises
•Connecting a keypad to test the control panel.
Do not connect the D5200 Programmer to
the SDI Molex connector.
3.3.2 Tip and Ring Posts
The tip and ring posts allow connecting a phone or
buttset for the purpose of troubleshooting
communications between the control panel and the
central station. This connection allows monitoring of
the dial tone, handshaking tones from the receiver,
and communications signals.
3.3.3 Super Capacitor
The D9412GV2 and D7412GV2 have a capacitor
called Super Cap. This component preserves the
parameters stored in the control panel’s RAM chip
when the lithium battery is replaced. The Super Cap
can retain voltage for up to 30 minutes after the
lithium battery is removed.

D9412GV2/D7412GV2 |Operation and Installation Guide | 3.0 Overview
12 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
Plan to replace the lithium battery after 3 to 5 years of
continual service.
When replacing the lithium battery,
ensure that you disconnect the primary
AC power and secondary battery power
from the control panel before you remove
the old battery. Then install the new
battery and connect the primary AC and
secondary battery power to the control
panel.
3.3.4 Telephone Line Sniff
The D9412GV2 and D7412GV2 control panels
monitor the phone line for the programmed
supervision interval before indicating a phone line
trouble. If trouble occurs, refer to the
D9412GV2/D7412GV2 Troubleshooting Guide (P/N:
F01U011024).
3.3.5 Points
The Bosch Security Systems, Inc. D9412GV2 Control
Panel provides up to 246 points of protection. The
D7412GV2 Control Panel provides up to 75 points of
protection. Point programming parameters determine
the control panel’s response to open and shorted
conditions on the sensor loop for the point. Several
options allow individual point programming to custom-
fit the protection to the installation.
Points 1 to 8 are located on the circuit board (on-
board points). They are standard sensor loops. The
remaining off-board points are POPIT points using
D8128D OctoPOPITs, D8125 POPEX Modules and
D9127 or D8127 POPITs. MUX devices can also be
used with D8125MUX or wireless transmitters with the
ISW-D8125CW and D8125INV.
3.3.6 Areas and Accounts
The system supports up to eight separate areas. You
can assign all points to a single area or distribute
them over as many as eight areas.
The control panel is armed and disarmed by area,
and several areas can be armed and disarmed with
one menu function. A passcode can also be assigned
an authority level that allows a user to arm an area
from a remote keypad in another area. Assigning
each area its own account number creates eight
separate accounts in one control panel. Assigning the
same account number to different areas groups them
together in a single account.
Area options include exit tone and delay, separate fire
and burglary outputs, and multiple opening and
closing windows. Area type can be used to create
area interdependencies for arming purposes.
3.3.7 Digital Communicator
The control panel uses a built-in digital communicator
to send reports to the receiver. The control panel
sends reports in either the Modem IIIa2or binary
frequency shift keying (BFSK) format. The
microprocessor unit (MPU) and line cards for the
D6500 receiver must have the correct software
revision installed to accept Modem IIIa2reports from
the control panel. Refer to Table 4. All software
versions for the D6600 can be used with the control
panel.

D9412GV2/D7412GV2 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 13
Table 4: Software Version Compatibility of
D6500 MPU and Line Cards
MPU Line Card Software Version
D6510 8.00 and higher
D6511 1.04 and higher
D6540 7.44 and higher
D6541 1.03 and higher
The control panel connects to an RJ31X or RJ38X
jack for telephone line seizure. Connecting to the
RJ31X complies with FCC regulations for using the
public telephone network. The control panel can be
programmed to direct reports to four separate
telephone numbers. Adding the D928 Dual Phone
Line Switcher Module allows connecting and
supervising a second telephone line.
The system can route groups of Event Reports to four
different destinations. Each report group can be
programmed to send reports to one or more
destinations. Primary and backup reporting paths can
be programmed for each destination and each report
group. A custom option allows specification of
individual Event Reports to be sent.
3.3.8 Keypads
Up to 32 unsupervised keypads can be connected to
the system. The available power, number of
supervised keypads, and number of areas covered
affect the total number of keypads that can be
connected.
The system can supervise up to eight keypads. The
control panel sends a Serial Device Trouble Report,
SDI FAILURE in the Modem IIIa2format or TROUBLE
ZN D in the BFSK format, if it loses communication
with a supervised keypad.
More than eight keypads can be added, but
supervision of only eight for is possible. Table 5 on
page 13 shows the keypads that are compatible with
the D9412GV2 and D7412GV2 Control Panels. Refer
to Keypad in the D9412GV2/D7412GV2 Program
Entry Guide (P/N: F01U003639) for complete details
on programming keypad options.
UL requires all Fire System keypads to be
supervised.
Table 5: Compatible Keypads and Command
Centers
Model Display Application
D1255/
D1255B/D
1255RB
16-character
alphanumeric
Fire/Burglary/Acces
s
D1256/
D1256RB
16-character
alphanumeric
Fire
D1257/
D1257RB
16-character
alphanumeric
Fire
D1260/
D1260B
4-line by 20-
character
Fire/Burglary
D720/
D720B
8 LED Fire/Burglary
3.3.9 Keyswitch
Maintained or momentary closure devices such as
keyswitches allow any of the available areas to be
armed or disarmed. Point programming determines
the loop responses and which area a keyswitch
controls.
3.3.10 Access Control
The D9412GV2 can control eight access doors (each
requiring the optional D9210B Wiegand Control
Interface Module) with up to 996 uniquely identified
cards or tokens. The D7412GV2 can control two
access doors with up to 396 uniquely identified cards
or tokens. Any of the following can grant access:
•Wiegand-style access control device (card
reader) connected to the D9210B Access Control
Interface Module
•Request to enter (RTE) or request to exit (REX)
input
•Unlock command on a keypad
The access control features of the D9412GV2 and
D7412GV2 can deny access during armed periods.
The control panel can also grant access only to
certain authorized users depending on whether the
area is master armed, perimeter armed, or disarmed.
Programming for automatic disarming when
designated authorized users are granted access is
also possible.
3.3.11 Event Memory
The system uses event memory to store events for
each area. A D1255, D1255B, D1255RB, D1260, or
D1260B Keypad assigned to an area allows viewing
of the events for the area. The control panel clears
the events for an area from event memory and starts
storing new events when the area is master armed.

D9412GV2/D7412GV2 |Operation and Installation Guide | 3.0 Overview
14 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
3.3.12 Event Log
The system stores from 500 to 1000 events and event
modifiers from all areas in its event log. Event
modifiers add information about an event to the log.
Some events are always followed by a modifier. For
example, the system adds at least two items to the
log each time an area is armed or disarmed, the Open
(or Close) event and an event modifier showing the
previous arming state.
All events and their modifiers can be stored even if
the control panel does not send a report for them. The
log can be viewed at a keypad, printed locally using
the D9131A Parallel Printer Interface Module and a
parallel printer, or uploaded using Remote
Programming Software (RPS).
For a list of the log events and event modifiers, refer
to the appendix in the user’s guide for the keypad.
3.3.13 Ground Fault Detection
The Earth Ground Terminal on the control panels is
electrically isolated from all other terminals to allow
the D9412GV2 and the D7412GV2 to detect ground
fault conditions. A Ground Fault Detect Enable switch
(S4) is located just under Terminal 10, Earth Ground,
on the control panel. Refer to Section 4.5.2 Ground
Fault Detect Enable on page 16 for information on
operating this function.
3.3.14 Ground Fault Detection Added Feature
When Ground Fault Detect is enabled (S4 closed),
Points 1 to 8 can be used for non-powered fire-
initiating devices such as heat detectors, four-wire
smoke detectors, and pull stations. A D125B Powered
Loop Interface or a D129 Dual Class A Interface
Module is not required when connecting the non-
powered fire-initiating devices to Points 1 to 8.
3.3.15 Conettix Functions
The D6600 Conettix System supports data network
communications. Conettix allows the D6600 receiver
to connect to network topologies, specifically
Ethernet. Conettix also allows this receiver to process
messages to and from most networks using TCP/IP
protocols. Connecting to a data network is possible
using the COM4 or COM1 connection from the D6600
receiver to the D6680 Network Adapter. Alarm control
panels can send reports through telephone lines or
Ethernet and token-ring data networks to the D6600
receiver and then to the central station automation
software or the network printer through a local area
network (LAN) or wide area network (WAN). The
network can monitor the status of alarm control
panels.
3.3.16 Programming
Use the Bosch Security Systems D5200 Programmer
or the Remote Programming Software (RPS) to
program the D9412GV2 and D7412GV2 Control
Panels. Refer to the D9412GV2/D7412GV2 Program
Entry Guide (P/N: F01U003636) for programming
options.
3.3.17 Other Features
D9412GV2 and D7412GV2 Control Panels have
many programmable features. Some of the features
are listed below. Complete details on all features are
in the D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636).
•Supervision of AC (primary power), battery
(secondary power), Zonex and SDI buses, central
processing unit (CPU), up to three printers, and
two telephone lines
•Automatic System Test Reports
•Remote access for programming, diagnostics,
and log uploads using the remote programming
software (RPS)
•Fire alarm verification
•Programmable alarm output
•Programmable relay output using the D8129
OctoRelay Module
•Opening and closing windows
•Skeds (scheduled events)

D9412GV2/D7412GV2 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 15
4.0 Installation
4.1 Installation Preparation
This section contains a general installation procedure
and refers to other sections of the document for
detailed instructions.
Review this document and the D9412GV2/D7412GV2
Program Entry Guide (P/N: F01U003636) before
beginning the installation to determine the hardware
and wiring requirements for the features used.
Have the following documentation available when
reading through this guide:
•D9412GV2/D7412GV2 Program Record Sheet
(P/N: F01U003635)
•Security System Owner’s Manual
(P/N: 71-06633-000) and GV2 Series Owner’s
Manual Supplement (P/N: F01U0063791)
•Installation manual for keypad, command center,
or annunciator (D1255, D1255B, D1255RB,
D1256, D1256RB, D1257, D1257RB, D1260,
D1260B, D720, or D720B)
Before installation, become familiar with the operation
of the D5200 Programmer or the RPS.
4.2 Enclosure Options
Mount the control panel assembly in any of the Bosch
Security Systems, Inc. enclosures listed:
•D8103 Universal Enclosure (tan)
•D8109 Fire Enclosure (red)
•D8108A Attack Resistant Enclosure (tan)
Refer to the D9412GV2/D7412GV2 Approved
Applications Compliance Guide (P/N: F01U003639)to
determine if the application requires a specific
enclosure.
4.3 Mounting Enclosure
1. Run the necessary wiring throughout the
premises.
2. Mount the enclosure in the desired location. Use
all five enclosure mounting holes. Refer to
Figure 2.
3. Pull the wires into the enclosure.
Electromagnetic interference (EMI) can
cause problems on long wire runs. For
more information, refer to “Noise on Wire”
in the General Wiring Troubleshooting
section of the D9412GV2/D7412GV2
Troubleshooting Guide
(P/N: F01U011024).
Figure 2: Enclosure Mounting
8
2
1
324
3
7
5
9
6
1 - Point chart label
2 - Mounting skirt hooks (2)
3 - Module mounting holes (12)
4 - Tamper switch mounting holes (5)
5 - Skirt mounting hole (1)
6- Enclosure mounting holes (5)
7 - Mounting skirt hook holes (2)
8 - Back of D9412GV2/D7412GV2 Control Panel
9 - Lock down tab

D9412GV2/D7412GV2 |Operation and Installation Guide | 4.0 Installation
16 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
4.4 Installing the Control Panel
1. Place the control panel over the inside back of the
enclosure, aligning the large rectangular openings
of the mounting skirt with the mounting hooks of
the enclosure. Slide the control panel down so
that it hangs on the hooks. Refer to Figure 2, Item
2on page 15.
2. Remove the tape from the #6 x 1/4-in. screw in
the mounting tab on the control panel. The screw
passes through the mounting tab and into the
skirt mounting hole in the enclosure. Tighten the
screw to secure the control panel in the
enclosure.
3. Connect earth ground to the control panel before
making any other connections. Refer to Section
4.5 Connecting Earth Ground.
4.5 Connecting Earth Ground
4.5.1 Terminal 10
To help prevent damage from electrostatic charges or
other transient electrical surges, connect the system
to earth ground at Terminal 10 before making other
connections. Recommended earth ground references
are a grounding rod or a cold water pipe.
Caution:
Do not use telephone or electrical ground
for the earth ground connection. Use
1.8 mm (14 AWG) to 1.5 mm (16 AWG)
wire when making the connection.
Do not connect other control panel
terminals to earth ground.
4.5.2 Ground Fault Detect Enable
To meet UL 864 requirements, enable
Ground Fault Detect.
A ground fault is a circuit impedance to earth ground.
The control panel has a ground fault detection circuit
that, when enabled, detects ground faults on
Terminals 1 to 9 and 11 to 32. The control panel also
detects and annunciates ground faults on any device
connected to it.
Control Panels with Firmware before Version 7.03
•To enable ground fault detection, the Ground
Fault Detect Enable jumper (S4) (Figure 3) must
be locked (closed) and a non-zero value must be
entered in the Area 5 Silent Alarm Relay. When
jumper S4 is in the unlocked (open) position, the
control panel does not detect ground fault
conditions.
•If a ground fault condition occurs, the keypads
display SERVC GND FAULT and the control
panel transmits a GROUND FAULT TROUBLE,
AREA 1 (Modem IIIa2format only).
When the control panel recognizes that the
ground fault condition is corrected, and remains
corrected for between 5 to 45 consecutive
seconds, a Restoral Report is sent.
The D9412GV2 and D7412GV2 Control
Panels log and print a Ground Fault event
as a Trouble Point 256 if communicating
in Modem IIIa2format. If communicating
in BFSK format, the control panels
generate an Alarm Zone 5 event.
Figure 3: Ground Fault Detection
GROUND FAULT DETECT
Enabled
Disabled S4
PHONE
LED
RED ON when
communicating
OFF when idle
PHONE LINE SEIZED
TIP RING
TELCO CORD
MODEL D161
3
1
2
1 - With S4 closed, control panel detects ground
faults.
2 - With S4 open, control panel does not detect
ground faults.
3 - S4, Ground fault detect enable

D9412GV2/D7412GV2 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 17
4.5.3 Enabling Ground Fault Detection
To enable the Ground Fault Detect Enable feature:
1. Lock (close) the S4 Ground Fault Detect Pin on
the control panel (Figure 4).
If your control panel has Version 7.02
firmware or earlier, you must do Step 2.
2. Program the Area 5 Silent Alarm Relay to a non-
zero value (1 to 128).
In remote programming software (RPS), the Area
5 Silent Alarm Relay is located in RELAY
PARAMETERS, Area Wide Relays, and Silent
Alarm Area 5 (Figure 5).
Figure 4: Ground Fault Detect (S4)
EARTH GROUND
COMMON
BATTERY NEGATIVE ONLY
BATTERY POSITIVE ONLY
RELAY A
RELAY B
RELAY C
+ AUX PO WER
CLASS 2 TRANSFORME R
16.5 VAC 40 VA60 Hz
Model D1640
Internally Fused - Do not short
Requires Uns witched Outlet
Do not share with other equipment
GROUND FAULT DETECT
Enabled
Disabled
PHONE
LED
RED
ON when
communicating
OFFwhen idle
Commercial Protected-Premises Control Panel
D9412GV2 Control Panel is UL Listed For Central Station, Local,Au xiliary, Proprietary, and
Household Fire Alarm, andCentralStation, Local, Police Station Connect, Household Burglar Alarm
and Encrypted Line Security when communicating viaa netwo rk.
System is intended to be checked by a QualifiedTechnician at least every3 years.
The types of initiating circuits the controlpanel has been ap proved for are A, M, W, SS.
The types of signaling the co ntrol panel has been approved for are DAC, OT, NC
VOLTAG E RANGES
Open 3.7 - 5.0 V DC S hort 0.0 - 1.3 VDC
Normal 2.0 - 3.0 VDC
Reset Pin
Disable all except Battery
Charging and Programming
PERIPHERAL DEVI CE CONNECTIONS
RED POWER +
YELLOW DATA BUS A
GREEN DATA BUS B
BLACK COMMON
ZONEX OUT1
ZONEX IN 1
N.F.P.A.
Style 4.0
Signaling
Line
Circuits
F01U003643-01
1211 13
Point 1 Point 2
1514 16
Point 3 Point 4
1817 19
Point 5 Point 6
2120 22
Point 7 Poi nt 8
LEDs Off When Normal
Charging Status
Low Battery - 12.1 VDC
YEL
RED
10.2 VDC - Battery Load Shed
This equipment sh ould be installed in accor dance witht heNFPA 70 (National Electrical Code)
and NFPA72 (National Fire Alarm Code) for Local, Central Station, Proprietaryand Household Fire
Warning Systems and under the limits of the Local Authority Having Jurisdiction (National Fire
Protection Association, Battermarch Park, Quincy, MA02269). Printedinformationdescribing
proper installation,operation, testing, maintenance, evacuation planningand repair service is to
be provided with this equipment.
D9412GV2
26
25
ZONEX PO WER + 24
ZONEX COMMON 23
PHON E LINE SEIZ ED
TIP RING
TEL CO COR D
MODEL D161
SDI Connector
ZONEX OUT 2
ZONEX IN 2
Refer to the D9412GV2/D7412GV2Approved Applications Compliance Guide(P/N: F01U003639)
For System Wiring Diagram, Issue A and for Compatible Smoke Detectors
POWER SUPPLY REQUIREMENTS
The PowerSupply provides amaximum of 1.4 Amps for the Control Paneland all
Accessory Devices. For System Loading, refer to the D9412GV2/D7412GV2
Operation and Installation G uide (P/N: F01U003641).
(P/N: F01U003641) forPowerRequirements relating to Terminals 6 and 7 .
CAUTION: Refer to th e D9412GV2/D7412GV 2 Operation and Installation Guide
All external connections except Terminal 5 (battery positive) are inherently power
limited.Requirements for battery standby time might reduce allowable output.
WARNING!
Multi-Battery installation requires
Model D122/D122L Dual Battery
Harness. Improper installation can
be a fire hazard.
Battery: Replace every 3 to
5 years wit h one or two Model
D126 or D1218 12V Lead Acid
Batteries.
GRN
D5200/D5360
PROG CONN
Point 8
S3 Option
Closed = 1KΩEOL
Normal Operation
Open =AB-12 UL
Bell Box 220 KΩ
Incorrect wiring will
damage this equip ment.
Suitable for dry indoor
use only.
Devices powered by the
AUX power output must
be supervised.
Minimum system requirements for Classification i n accordance with ANSI/SIA CP-0 1-2000:
UL Listed and Classified control unit Model D9412GV2, D7412GV2, orD 7212GV2;
UL Listed and Classified keypad Model D1256, D1257, D1260,D 1255, D1255R,or D1255RW;
ULListed Local Bell
CAUTION: Avoid damage to Panel.
Do not connect 24V to terminals.
Maximum charging current 1.4A
PROGRAMMABLE
ALARM OUTPUTS
Ter m i nal s
SWITCHED AUX
and
67
Terminal
8
Reset Pin
Disabl e All Except Ba ttery
Charging And Programming
27
PROG
CONN
26
25
24
2
1
1 - Locked (Closed) 2 - Unlocked (Open)
Figure 5: Area 5 Silent Alarm Relay in RPS
4.5.4 D7212GV2 Ground Fault Specifications
Table 6 provides the impedance specifications for
detecting ground faults when any terminal or field
wiring is shorted to ground.
Table 6: Ground Fault Impedance
Specifications
Impedance Control Panel Detects Ground Fault
<300 ΩYes
300 Ωto
200>kΩDetection depends upon the terminal
> 200 kΩNo

D9412GV2/D7412GV2 |Operation and Installation Guide | 4.0 Installation
18 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
4.5.5 Locking the Reset Pin
Locking the reset pin disables the control panel
(Figure 6). When the control panel is disabled, the
system ignores the keypads and points. CALL FOR
SERVICE appears in keypad displays when the pin is
locked down.
On-board relays (Terminals 6 and 7) and off-board
relays deactivate when the control panel is reset.
Terminal 8 has power when the relay is deactivated.
Activation interrupts power at that terminal. The on-
board relay (Terminal 8) remains deactivated when
the reset pin is locked in the disable position.
Releasing the reset pin from the closed position
resets the control panel. The control panel resets all
its timers, counters, indexes, and buffers. Any points
that restore after a reset do not generate Restoral
Reports.
If the reset pin is placed in the disable position when
all areas are armed, there must be an entry in the
Answer Armed program item. Refer to RPS
Parameters in the D9412GV2/D7412GV2 Program
Entry Guide
(P/N: F01U003636).
Locking the pin in the disable position applies power
to the control panel and charges the battery while the
detection devices and keypads are installed.
Figure 6: Reset Pin
Reset Pin
Disable All Except Battery
Charging And Programming
PERIPHERAL DEVICE CONNECTIONS
RED POWER +
YELLOW DATA BUS A
GREEN DATA BUS B
BLACK COMMON
32
31
30
29
1
2
1 - Reset pin locked (closed).
2 - Reset pin normal (open).
4.6 Completing the Installation
If not already complete, make the earth ground
connection to Terminal 10 and lock the reset pin in
the closed position.
4.6.1 Charging the Battery
Connect the battery, then the transformer to allow the
control panel to charge the battery while you complete
the installation. Refer to Section 5.0 Power Supply on
page 23 for instructions.
On-board Buzzer Sounds at Power Up and Reset:
The system performs a series of self-diagnostic tests
of hardware, software, and programming at power up
and at reset. The buzzer on the control panel sounds
during the tests. The self-diagnostics tests complete
in approximately 1 to 3 seconds.
If the control panel fails any test, the buzzer continues
sounding and a System Trouble message appears at
the keypads. Refer to Problems Found during Self
Diagnostics in the D9412GV2/D7412GV2/D7212GV2
Installation and Troubleshooting Quick Reference
Guide (P/N: F01U003638) for a description of each
system trouble message.
Touch Terminal 10 First: If the on-board buzzer
sounds briefly when the control panel is touched, any
static charge you carry discharges to the control
panel.
Avoid electrostatic discharge. Always
touch Terminal 10, the earth ground
connection, before beginning work on the
control panel.
If the control panel receives an electrostatic
discharge, it might generate Watchdog Reset and
Param Fail events.
4.6.2 Installing and Wiring Detection Devices
Install and wire detection devices and keypads at their
locations throughout the premises. Do not connect
the control panel yet.
Section 8.0 On-Board Points on page 35 contains
instructions for wiring the on-board points to detection
devices. Section 11.0 Arming Devices on page 58
contains instructions for wiring the keypads.
Instructions for wiring the off-board point POPIT
sensor loops are found in the instructions packaged
with the POPIT modules.

D9412GV2/D7412GV2 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 7/09 | F01U003641-04 19
4.6.3 Installing Modules and Relays
1. Power down the unit by unplugging the
transformer and disconnecting the battery.
Always power down the unit when
installing modules or relays, or when
making wiring connections to the control
panel.
2. Install and wire any modules required for the
installation as described in the module’s
installation instructions.
Instructions for the D8125 POPEX Module,
D8128D OctoPOPIT Module, D8129 OctoRelay
Module, D811 Arm Status Relay Module, and
D928 Dual Phone Line Switcher appear in this
guide.
Refer to Section 9.0 Off-Board Points on page
39 for D8125 and D8128D instructions. Refer to
Section 10.0 Off-Board Relays on page 53 for
D8129 and D811 instructions. Refer to Section
7.11 D928 Dual Phone Line Switcher on page 32
for D928 instructions.
3. If using the power outputs at Terminals 7 or 8,
refer to Section 6.4 Programmable Power Output
Terminals 6, 7, and 8 on page 28 for
instructions.
4.6.4 Connecting the On-board Points and
Keypads
Connect the on-board points and keypad wiring to the
system. Refer to Section 8.0 On-Board Points on
page 35 and Section 11.0 Arming Devices on page 58
for instructions.
4.6.5 Powering Up
Reconnect the battery, then plug in the transformer.
The buzzer sounds for two seconds when the control
panel is powered up. Leave the reset pin in the locked
position.
Yellow Charging Status LED Remains Lit: If the
yellow charging status LED remains lit after five
minutes of powering up the control panel, either the
battery is deeply discharged or too many powered
devices were connected to the control panel.
Combined continuous current draw for Terminals 3, 8,
24, and 32, and the accessory connector cannot
exceed 1.4 A. Refer to Section 6.0 Power Outputs on
page 28 for help.
4.7 Programming the Control Panel
If the control panel is not already programmed, review
the D9412GV2/D7412GV2 Program Entry Guide
(P/N: F01U003636). Ensure that all accessory
modules for desired features are available for
installation. Place the reset pin in the locked position
to copy or send information to and from the control
panel.
Use the D5200 Programmer or the RPS to load a
custom program into the control panel.
Move the reset pin to the normal position refer to
(Figure 6 on page 18). The control panel sends
Reboot and Battery Reports to the receiver if
programmed for reporting.
4.8 Installing the Point Chart Label
The point chart label is required for fire
systems with verifications points.
A point chart label is included in the literature pack.
Install the point chart label for fire or combined fire-
and-burglary systems that use verification points.
Use the D9412GV2/D7412GV2 Program Record
Sheet (P/N: F01U003635) to gather the necessary
information for completing the point chart. Fill out the
label and install it on the inside of the enclosure door
(refer to Figure 2 on page 15).
Avoid smearing the entries on the chart.
Use the peel-off backing to press the
label in place.
4.9 Testing the System
After installing and programming the control panel,
test the system completely. Test the control panel and
all devices for proper operation.
Test after initially programming the control
panel.
To meet UL 864 requirements, perform a
full system test after any subsequent
programming session.
Refer to Section 4.10 Service Walk Test on page 20
for complete Service Walk Test instructions.
Clear after Test: To clear the event memory and
report buffer, momentarily close the reset pin. Events
stored in the control panel’s event log are not cleared.

D9412GV2/D7412GV2 |Operation and Installation Guide | 4.0 Installation
20 Bosch Security Systems, Inc. | 7/09 | F01U003641-04
4.10 Service Walk Test
The Service Walk Test differs from the standard Walk
Test. In the standard Walk Test, POPITs whose
switches are set for a point number not programmed
in the control panel do not appear in the test. In the
Service Walk Test, POPITs whose switches are set
for a point number that is not programmed in the
control panel do appear in the test.
The Service Walk Test allows a user to walk test all
246 points from a control-panel-wide keypad,
regardless of the point index type.
A Service Walk Test can also be initiated by account-
wide or area-wide keypads but test only those points
that are within the scope of the keypad that initiated
the function. The Service Walk Test does not test
points in armed areas.
Only Walk Test Start and Walk Test End
are reported to the central station.
The D9131A can be configured for local
printing. Refer to the D9412GV2/
D9412GV2 Program Entry Guide
(P/N: F01U003636).
During a Service Walk Test, the summary
alarm and summary fire remain off,
because there are no Fire or Burg alarm
conditions to summarize. The P# Relay
Response Type feature operates as
programmed.
Service Walk Test Procedure.
Refer to Figure 7 on page 21 and Figure 8 on page 22
for Service Walk Test options. Refer to the Walk Test
procedures in the GV2 Series Owner’s Manual
Supplement (P/N: F01U063791) when using a D1260
or D1260B Keypad.
1. Choose a keypad to conduct the test. Ensure that
the display shows the idle disarmed text.
2. Press the [MENU] key to enter the Function List.
Press [NEXT] repeatedly until the SERVICE
WALK ? prompt appears.
3. Press [ENT], or press [9][9] followed by [ENT] to
reach the Service Menu to access the Service
Walk Test.
The D7412GV2 does not include the
Service Walk Test in the Service Menu.
Enabling the Service Walk Test function
in the Function List provides access to
the Service Walk Test in the D7412GV2.
4. The display shows ### PTS TO TEST .Test the
first detection device.
5. When a detection device is faulted, the keypad
emits a brief tone and displays the point text of
the point tested for 60 seconds. After 60 seconds,
the display returns to the ### PTS TO TEST
message.
Extra Points display default text: If the switches on
a POPIT are set incorrectly to a point number that is
not in the program for the control panel, the default
text for that point number (PT ###) appears when the
point is faulted. Refer to the control panel’s program
record sheet for the default text for all points.
Faulting the point a second time produces the tone
and shows the point text, but does not decrease the
count in the ## PTS TO TEST message.
5. To see the points that remain untested during the
Service Walk Test:
a. Press [ESC] when point text appears. The
display shows ## PTS TO TEST.
b. Press the [ESC] key. VIEW UNTESTED ?
appears.
c. Press [ENT]. ## PTS UNTESTED appears.
d. Press [NEXT] to see a list of the points that
have not yet been tested. Move through this
list by pressing the [NEXT] key.
e. To resume the Service Walk Test, press
[ESC]. ## PTS UNTESTED appears.
f. Press [ESC]. ## PTS TO TEST appears.
g. Resume testing points. To end the Service
Walk Test, press [ESC] twice.
6. After the last point is tested, 0 PTS TO TEST
appears. Press [ESC]. The display shows ALL
PTS TESTED briefly before returning to idle text.
The Service Walk Test, when performed
on a D7412GV2, cannot display “0 PTS
TO TEST” because the D7412GV2 is
physically unable to connect to the
second POPEX Module (used for Points
129-247).
Automatic time-out returns the system to
idle text: If there is no point or keypad
activity for 20 min., the Service Walk Test
ends automatically. The keypad returns to
idle text.