Bosch Solution 2000 User manual

Control Panel
Solution 2000 / 3000
en User's Guide

Control Panel Table of contents | en 3
Bosch Security Systems, Inc. User's Guide 2017.09 | 04 | F.01U.298.028
Table of contents
1Introduction 5
2Specifications 6
3Codepad Introduction 7
3.1 Codepad 7
3.2 Codepad Indicators 7
3.3 Audible Indications 9
4Operation with TEXT LCD Codepad 10
5Operation with ICON LCD Codepad 12
5.1 Arming the System 12
5.1.1 Forced Arming 12
5.1.2 Arming in AWAY Mode 12
5.1.3 Arming in STAY Mode 1 13
5.1.4 Arming in STAY Mode 2 13
5.1.5 Programming STAY Mode 2 Bypass Zones 14
5.2 Disarming the System 14
5.3 Arming/Disarming Areas 14
5.4 User Codes 15
5.4.1 Adding User/Radio Codes 15
5.4.2 Deleting User/Radio Codes 16
5.5 Codepad Alarms 16
5.5.1 Codepad Duress Alarm 16
5.5.2 Codepad Panic Alarm 16
5.5.3 Codepad Fire Alarm 17
5.5.4 Codepad Medical Alarm 17
5.5.5 Codepad PIN Error (Access Denied) 17
5.6 Isolating Zones 17
5.6.1 Standard Isolating 17
5.6.2 Code to Isolate 17
5.7 Fault Analysis Mode 18
5.7.1 Fault Descriptions 19
5.8 Date and Time 20
5.9 Turning Outputs On/Off 20
5.10 Reset Latching Outputs 21
5.11 Telco Arm/Disarm Sequence (Call Forward On/Off) 21
5.11.1 Telco Arm Sequence 21
5.11.2 Telco Disarm Sequence 21
5.12 Testing 22
5.12.1 Horn Speaker Test 22
5.12.2 Bell Test 22
5.12.3 Strobe Test 22
5.12.4 Walk Test Mode 22
5.12.5 Test Report 23
5.13 Event Memory 23
5.14 Day Alarm 23
5.15 Codepad ID / Buzzer Tone 23
5.16 Remote Arming by Telephone 24
5.17 Domestic Dialing 24
5.17.1 Acknowledging Domestic Calls 24

4en | Table of contents Control Panel
2017.09 | 04 | F.01U.298.028 User's Guide Bosch Security Systems, Inc.
5.17.2 Programming Domestic Telephone Numbers 25
5.17.3 Disable Domestic Dialing 25
6Glossary of Terms 26

Control Panel Introduction | en 5
Bosch Security Systems, Inc. User's Guide 2017.09 | 04 | F.01U.298.028
1 Introduction
Congratulations on selecting the Solution 2000 / Solution 3000 Control Panel to protect you
and your property. To obtain the most from your unit, take time to read through this manual
and familiarize yourself with the numerous outstanding operating features of this system. In all
aspects of planning, engineering, styling, operation, convenience, and adaptability, we have
sought to anticipate your every possible requirement.
Programming simplicity and speed were some of the major considerations and we believe that
our objectives in this area were more than satisfied.
This manual explains all aspects of operating the control panel. All system parameters and
options are detailed; however, suitability is left up to the individual. Every system can be
tailored to meet all requirements quickly and easily.

6en | Specifications Control Panel
2017.09 | 04 | F.01U.298.028 User's Guide Bosch Security Systems, Inc.
2 Specifications
Temperature Range 0℃ to +50℃
Humidity 20% to 90%
Power Source TF008 Plug Pack – 240 V/18 VAC @ 1.3A
Stand-By Current 65 mA
Current Draw in Alarm Condition 115 mA
Current Draw in Alarm Condition with
Codepad
105 mA
Back-Up Battery 7 Ah/12 VDC Rechargeable Sealed Lead Acid
Battery
Supplier Code N771
Tab.2.1: Specifications
Notice!
Test the sirens, strobe, and zones at weekly intervals.

Control Panel Codepad Introduction | en 7
Bosch Security Systems, Inc. User's Guide 2017.09 | 04 | F.01U.298.028
3 Codepad Introduction
3.1 Codepad
IUI – SOL -TEXT IUI – SOL – ICON
1 2 3
4
7
#
8
0
9
5 6
*
1
4
7
2
5
8
3
6
9
STAY # AWAY
0
*
1 2 3 4 5 6 7 8
ON
OFF
3.2 Codepad Indicators
Codepad indicator
icons
Status Definition
ZONE 1 – 8 for
Solution 2000
ZONE 1 – 16 for
Solution 3000
On Zone is unsealed.
Off Zone is sealed.
Flashing Fast (0.25 sec
on/0.25 sec off)
Zone is in alarm condition.
Flashing Slow (1 sec on/1
sec off)
Zone is manually isolated or selected to
be isolated.
AWAY
On System is armed in AWAY Mode.
Off System is not armed in AWAY Mode.
Flashing twice a sec with
STAY indicator
Setting STAY Mode 2 bypass zones.

8en | Codepad Introduction Control Panel
2017.09 | 04 | F.01U.298.028 User's Guide Bosch Security Systems, Inc.
Codepad indicator
icons
Status Definition
STAY
On System is armed in STAY Mode 1 or
STAY Mode 2.
Off System is not armed in STAY Mode 1 or
STAY Mode 2.
Flashing twice a sec Zone isolating mode
Flashing twice a sec with
AWAY indicator
Setting STAY Mode 2 zones.
Flashing once every 3 sec Day alarm status – day alarm turned on.
On System is disarmed.
MAINS
On AC MAINS power normal.
Flashing AC MAINS supply has failed.
FAULTS
On There is a system fault that needs to be
rectified.
Off The system is normal, there are no
faults.
Flashing There is a system fault that needs to be
acknowledged.
Programming Mode
Flashing These two indicators flash when you
enter Installer’s Programming Mode or
use any Master Code function.
The OFF indicator lights when the
system is disarmed and flashes when a
zone becomes unsealed when
disarmed. The indicator stops flashing
when all zones are sealed.
The ON indicator lights when the
system is armed and flashes when an
alarm occurs. The indicator is reset
after a valid User Code is entered.
Tab.3.2: Icon Indicators

Control Panel Codepad Introduction | en 9
Bosch Security Systems, Inc. User's Guide 2017.09 | 04 | F.01U.298.028
3.3 Audible Indications
The table below defines the audible indicators given out by the codepad buzzer.
Audible Indicator Definition
One short beep A button/key was pressed on the codepad, or Exit Time ended
when armed in STAY Mode 1 or STAY Mode 2.
Two short beeps The system accepted your code.
Three short beeps The requested function was executed.
One long beep Indicates the last 10 seconds of Exit Time when armed in AWAY
Mode, or the requested operation was denied or aborted.
Indicates codepad panic/fire/medical alarm operation.
One beep every sec Walk Test Mode is currently active.
One short beep every min There is a system fault waiting to be acknowledged.
One beep every 4 sec. During Auto Arming Pre-Alert Time, the warning before
automatic arming takes place.
One beep every 2 sec. During Exit Time when armed in AWAY Mode.
Tab.3.3: Audible Indicators

10 en | Operation with TEXT LCD Codepad Control Panel
2017.09 | 04 | F.01U.298.028 User's Guide Bosch Security Systems, Inc.
4 Operation with TEXT LCD Codepad
Users with authority levels enter their own user menu via TEXT LCD codepad.
1. Enable Text codepad and confirm that the system is in disarmed status.
2. To enter User Menu, enter the user code (Default = 2580) followed by the [-] key.
3. Select the menu and operate according to the menu prompt
Command
User Code
Inquire
System
Zone bypass
Test
1
2
3
6
5
Fault analysis1
Event recall
Cloud status
2
3
Set date & time
Day alarm
1
Arm/disarm seq.
2
Modem call init.
5
Domestic phone
6
Version display
System reset
7
Arm
1
AWAY arm
STAY1 arm
STAY2 arm
AWAY arm all
2
3
4
Horn speaker1
Bell test2
Strobe test
3
Walk test
4
Test report
5
Output on/off
7
Access
2User code
2
User name
User Allocate
1
2
User property
4
System
Wireless
System option
3
5
6
Keyfob RFID3
Home message1
[185]
[2920]
[534]
[1500]
[2500]
3
9
Zone
Zone name
STAY2 zone
4
3
5
[2536]
[381]
1
Without any codes, users can enter the general menu by pressing [-] key.