Bosch SOLUTION 3000 User manual

Control Panel
Solution 2000 / 3000
en Quick Reference Guide

Table of contents
1Introduction 6
2Programming 7
2.1 TEXT LCD Codepad Menu Programming 7
2.2 ICON LCD Codepad Programming 10
2.3 Programming Option Bits 11
2.4 Installer's programming commands 11
3Operating Commands 12
3.1 Add/Delete RF Device (Wireless Zones) 14
3.2 Add/Delete RF Repeater 14
3.3 Add/Delete RF Keyfob 15
3.4 Set the Number of Days until the First Test Report 16
3.5 Change Domestic Telephone Numbers 16
3.6 Change the Telco Arm/Disarm Sequence 16
3.7 Set STAY Mode 2 Bypass Zones 16
3.8 Report Monitor Mode (Toggle On/Off) 16
3.9 Walk Test Mode 17
3.10 Event Memory Recall 17
3.11 Fault Analysis Mode 17
4Programming Parameters 20
4.1 Communication Programming 20
4.1.1 Receiver 1 20
4.1.2 Receiver 2 20
4.1.3 External Network Module 22
4.1.4 Password for A-Link Plus/RSC Connection 23
4.1.5 DTMF Timing Compensation 23
4.1.6 Country Codes 23
4.1.7 Telco Arming Sequence (Call Forward On) 23
4.1.8 Telco Disarm Sequence (Call Forward Off) 23
4.1.9 Call Back Telephone Number 23
4.1.10 Ring Count 23
4.1.11 Telephone Line Fail Options 24
4.1.12 Communication Options 1 24
4.1.13 Communication Options 2 24
4.1.14 Communication Options 3 24
4.1.15 A-Link Plus Options 25
4.2 Installer Code 25
4.3 User Code Programming 25
4.4 Day Alarm Zones 27
4.5 EOL Resistor Value 27
4.6 Zone Programming 27
4.7 Swinger Programming 30
4.7.1 Swinger Shutdown Count For Siren 30
4.7.2 Swinger Shutdown Count For Report 31
4.8 Zone Status Programming 31
4.8.1 STAY Mode 2 Automatically Bypass Zones 31
4.8.2 Zone Status Reporting Options 31
4.9 RF Programming 31
Control Panel Table of Contents | en 3
Bosch Security Systems, Inc. Quick Reference Guide 2015.06 | 03 | F.01U.298.027

4.9.1 RF Supervision Time 31
4.9.2 RADION Anti-Jamming Sensitivity 32
4.9.3 RF Receiver 32
4.9.4 RF Options 32
4.10 Report Programming 32
4.10.1 Arm / Disarm Reporting Options 32
4.10.2 Codepad Reporting Options 32
4.11 System Status Programming 33
4.11.1 Access Denied(Code Retry) 33
4.11.2 System Status Reporting Options 33
4.12 Test Report Programming 33
4.12.1 Test Report Time (Automatic) 33
4.12.2 Test Reporting Options 33
4.13 Output Programming 34
4.14 Time Programming 39
4.14.1 Entry Time 1 39
4.14.2 Entry Time 2 39
4.14.3 Exit Time (AWAY/STAY Modes) 39
4.14.4 Entry Guard Time For STAY Mode 39
4.14.5 Delay Alarm Report Time 39
4.14.6 Sensor Watch Time 40
4.14.7 Codepad Lockout Time 40
4.14.8 Siren Run Time 40
4.14.9 Siren Sound Rate 40
4.14.10 Auto Arming Pre-Alert Time 40
4.14.11 Auto Arming Time 40
4.14.12 Auto Disarming Time 41
4.14.13 Kiss-Off Wait Time 41
4.14.14 Speaker Beep Volume 41
4.15 Options Programming 41
4.15.1 System Options 1 41
4.15.2 System Options 2 41
4.15.3 System Options 3 42
4.15.4 System Options 4 42
4.15.5 Consumer Options 1 42
4.15.6 Consumer Options 2 42
4.15.7 Consumer Options 3 42
4.15.8 Partitioning Options 1 43
4.15.9 Partitioning Options 2 43
4.16 Partition Allocations 43
4.16.1 Zone Area Assignment 43
4.16.2 Codepad Assignment 44
4.16.3 User Code Area Assignment 44
4.17 Default Options 44
4.18 RFID Programming 45
4.18.1 Keyfob RFID 45
4.18.2 Zone/Device RFID and RF Zone Option 45
4.18.3 Repeater RFID 46
4.19 Text Codepad Items 46
4.19.1 Home Message 46
4en | Table of Contents Control Panel
2015.06 | 03 | F.01U.298.027 Quick Reference Guide Bosch Security Systems, Inc.

4.19.2 Zone Names 46
4.19.3 User Names 47
5Appendices 48
5.1 Connections for EOL Resistors 48
5.2 Wiring Diagram 49
5.3 Component Overlay 50
5.4 Codepad Address Setting 51
Control Panel Table of Contents | en 5
Bosch Security Systems, Inc. Quick Reference Guide 2015.06 | 03 | F.01U.298.027

Introduction
Thank you for choosing the Solution 2000 / 3000 Control Panel for your installation. You will
find this system extremely flexible, reliable, and easy to use. This Quick Reference Guide is
supplied with the system to provide users with enough basic information to wire, configure,
and program the system. Due to the systems many programmable features and options, we
suggest that you obtain the Installation Guide that provides detailed information on system
options, functions, and programming methods.
Throughout this document, the words “control panel ” refer to all control panels covered by
this document ( Solution 2000 / Solution 3000 ).
Features Solution 2000 Solution 3000
Number of users 32 32
HCT-4 Keyfobs – WE800EV2 required 21 21
RADION RFKF Keyfobs – RADION B810 required 0 32
Number of areas / partitions 2 2
Number of zones / inputs 4 + 4 (ZD) 8 + 8 (ZD)
Number of Onboard outputs 4 4
Number of text LCD codepads IUI-SOL-TEXT or
ICON LCD codepads IUI-SOL-ICON
4 4
Number of Touchscreen codepads IUI-SOL-4TS
or IUI-SOL-7TS *
1 1
Number of wireless receiver WE800EV2 * 1 1
Number of RADION receiver B810 0 1
Number of RADION repeater RFRP 0 8
Number of B308 Octo-output Modules 2 2
Number of B426 Conettix Ethernet
Communication Modules *
2 2
Number of B450 Conettix Plug-in Communicator
Interfaces
2 2
Table 1.1: Control Panel Capacities
* Including the touchscreen codepad, up to 4 codepads can be used per system.
* Receiver WE800EV2 and B810 are mutually exclusive.
* A total of 2 B426/B450 can be used per system.
1
6en | Introduction Control Panel
2015.06 | 03 | F.01U.298.027 Quick Reference Guide Bosch Security Systems, Inc.

Programming
The programming options of the system are stored in a non-volatile EPROM. This memory
holds all information during a total power loss and can be changed as many times as required.
The entire programming sequence consists of entering a location number and changing the
data as required.
Use the following methods to program the system:
– Codepad
– A-Link Plus Software
TEXT LCD Codepad Menu Programming
1. Enable Text codepad and confirm that the system is in disarmed status.
2. To enter Installer’s Programming Menu, enter the installer code (Default = 1234) followed
by the [#] key or [-] key.
3. Programming: Select the menu and operate according to the menu prompt.
– Down to the next menu: Press [▼]
– Up to the previous menu: Press [▲]
– Enter menu or confirm input : [#]
– Back to the menu or exit programming item setting: Press [-]; or press and hold [-]
for 3 seconds to exit programming without saving changes.
– Operate according to the menu prompt. Select menu and enter or select data for
specific programming items to complete programming, step by step. For specific
items and options, refer to Programming Parameters, page 20.
4. After completing input, press [-] to get back to the previous menu. Complete all
programming input by repeating step 3 and press [-] to get back to the current main
menu level by level.
5. To use the TEXT LCD codepad in location programming mode (like IUI-SOL-ICON ), enter
programming option [8] [1].
– In location programming mode enter the programming location then [#].
– Enter the new data then [*] to save it. Enter [#] to go to the next location.
6. When [Confirm to Save Parameter Changes?] display, press [#] to save parameter
changes , exit menu programming and reset system.
2
2.1
Control Panel Programming | en 7
Bosch Security Systems, Inc. Quick Reference Guide 2015.06 | 03 | F.01U.298.027

.
Command
Installer
Passcode
Inquire
System
RF diagnose
Test
1
2
3
4
5
Fault analysis1
Event recall
2
Day alarm2
Arm/disarm seq.
3
Report monitor
4
Modem call init.
5
Domestic phone
6
Version display
7
Factory default
8
RF zone1
RF Keyfob
2
RF Repeater
3
Horn speaker1
Bell test2
Strobe test
3
Walk test
4
Test report
5
Access
2
Installer code
Access retry
1
3
User allocate2
User authority
3
User property
4
System
Timer
Codepad
Arm/disarm
Fault
Wireless
System option
3
1
2
3
4
5
6
Entry time11
Entry time2
2
Exit time3
Entry guard time for STAY mode
4
Sensor watch time
5
Codepad lockout time6
Auto arm pre-alert time
7
Auto arm time
8
Auto disarm time9
Silent codepad panic alarm1
Silent codepad fire alarm2
Silent codepad medical alarm3
Codepad access denied silent
4
Codepad fault beep enable
5
Codepad display off after 60s
6
Auto arm in STAY11
Single button arm enable2
Single button disarm enable
3
Disarmed on power up
4
Arm/disarm track on power up
5
Phone remote arm
6
Answer machine bypass on arm
7
Ignore AC fail1
AC fail report wait time
2
Warning device fault monitor
3
Phone line fault indicator
4
Phone line fault alarm on armed
5
Phone line fault alarm on disarm
6
Lockout phone line fail alarm
7
RF receiver1
Zone RFID and input option
2
Keyfob RFID
3
Repeater RFID
4
RF supervision time
5
RF jam sensitivity
6
RF RECE jam/tamper siren alarm
7
RFKF button4 arm in STAY1
8
RF arm/disarm strobe indicator
9
Home message1
Button factory default enable
2
Alarm memory reset on disarm
3
STAY indicator for day alarm
4
Digit 3 for codepad duress alarm
5
Siren and strobe output in STAY
6
Speaker beep volume
7
8Country code
[181]
[424]
[189]
[534]
[466]
[468]
[470]
[472]
[476]
[478]
[481]
[482]
[486]
[493.1]
[493.2]
[493.3]
[493.4]
[498.1]
[497.1]
[496.3]
[497.2]
[497.3]
[495.1]
[495.2]
[177.2]
[177.3]
[494.2]
[494.1]
[492.2]
[176.1]
[176.2]
[176.3]
[179.2]
[395]
[1820]
[1500]
[1980]
[393]
[394]
[396.2]
[492.4]
[492.3]
[2500]
[900]
[497.4]
[496.4]
[498.2]
[498.3]
[491]
[112]
8en | Programming Control Panel
2015.06 | 03 | F.01U.298.027 Quick Reference Guide Bosch Security Systems, Inc.

Zone
Zone config
Installer
Passcode
Zone allocate
Zone name
Day alarm zone
STAY2 zone
EOL resistor
Zone state report
4
1
2
3
4
5
6
7
Siren swing shutdown count1
Report swing shutdown count
2
Telco arming sequence
1
Telco disarming sequence
2
Delay alarm report time
3
Kiss-off wait time
4
Delay siren until transmit over
5
Extend wait for handshake
6
Upload/download enable
7
Callback phone number request
8
Callback phone number
9
Siren run time
1
Siren sound rate
2
Siren sound on RF receiver fail
3
Silent zone tamper alarm1
Unseal RF zone that failed monitor
2
Bosch Smart Lockout enable
3
Zone pulse count handover enable
4
Handover delay in order
5
Area
5Codepad area
Area option
1
2
Output
6
STAY mode arm/disarm report enable1
Arm/disarm report only if alarmed2
First disarm/last arm report3
Arm/disarm report option
4
Codepad report option
5
Test report time and interval
6
Test report only when armed
7
Test report on siren reset
8
Test report option
9
First phone number1
Second phone number2
Transmit format
3
Subscriber ID number
4
IP + Port / Email
Conettix ACK wait time
Conettix heart beat time
Conettix anti-replay enable
5
CSVIP user name and password
6
Ring count1
Report function enable
2
Exit A-Link connection on alarm
3
System status report option
4
Use bell-103 for FSK format5
DTMF dial pulse to 1 digit/sec
6
Set up domestic dialing format
DTMF timing compensation [111]
7
Swing shutdown
8
Zone option
9
Arm/disarm all areas once1
Reset siren from any area
2
Onboard output
Codepad output
Extend output
Siren config
1
2
3
4
Comm
7Receiver config
Network config
Report config
Comm option 1
Comm option 2
1
2
3
4
5
Network module1
A-Link/RSC password
2
Parameter
8Address program
Address auto step
Adapter
1
2
3
Test adapter
1
Read adapter
2
Write adapter
3
[267]
[502]
[2536]
[265]
[381]
[266]
[392]
[379]
[380]
[498.4]
[396.3]
[492.1]
[494.3]
[494.4]
[501.2]
[500.3]
[518]
[436]
[460]
[646]
[177.4]
[0, 40]
[16, 56]
[33, 73]
[34, 74]
[1000, 1200]
[1100, 1300]
[1401, 1405]
[1403, 1407]
[1400]
[479]
[480]
[396.1]
[81,82]
[83]
[175]
[177.1]
[180.3]
[427]
[178.2]
[178.1]
[500.1]
[403]
[411]
[428, 434]
[496.1]
[496.2]
[435]
[179.1]
[*]
[474]
[490]
[178.3]
[178.4]
[180.1]
[180.2]
[159]
[113]
[143]
8
7
8
9
Figure 2.1: TEXT LCD Codepad Programming Menu
Control Panel Programming | en 9
Bosch Security Systems, Inc. Quick Reference Guide 2015.06 | 03 | F.01U.298.027

ICON LCD Codepad Programming
The system must be disarmed (with no active alarm) to program the system. If there is an
active alarm or the system is armed, enter the code for User 1 (Default = 2580) followed by
the [#] key. (User Code 1 is factory default as the Master Code.)
1. Enter Installer’s Programming Mode: Enter the installer code (Default = 1234) followed by
the [#] key. Two beeps are heard and both the STAY and AWAY indicators flash
simultaneously to indicate that you entered programming mode. The codepad indicators
display the current data programmed in Location 0000 (first location of the Primary
Telephone Number).
2. Programming: Move to the required location and program new data into location.
– To move to another programming location, enter the location number followed by
the [#] key. The data in the new location is displayed using the codepad indicators.
(For example, if you enter [34 #], the system jumps to Location 0034, the beginning
of the Subscriber ID Number For Receiver 1.)
– To move to the next location, press the [#] key. This steps you to the next location.
The data in the next location is displayed using the codepad indicators. (For
example, if you are currently positioned at Location 0034, pressing [#] key takes you
to Location 0035.)
– To step back one location, press the [*] key. (For example, if you are currently
positioned at Location 0035, pressing the [*] key returns to Location 0034.)
– To change data in the current location, enter the new value (0 to 15) followed by the
[*] key. This stores the new data into the location. (For example, if you enter the
value [14*], the Zone 14 indicator display to represent the new data value.)
3. Exit from Installer’s Programming Mode with saving changes: Enter [960#]. Two beeps
are heard and the STAY and AWAY indicators no longer display. The system returns to the
disarmed state and is ready for use.
Task Keystrokes
Enter Installer’s Programming Mode [1234#]
Exit from Installer’s Programming Mode
without saving changes
[958#]
Exit from Installer’s Programming Mode with
saving changes and panel reset
[960#]
Step to next Location [#]
Step back one Location [*]
Program new data into Location [Data][*] (Data = 0 to 15)
Jump to another Location [Location No.] [#]
Table 2.1: Quick Guide to Programming
2.2
10 en | Programming Control Panel
2015.06 | 03 | F.01U.298.027 Quick Reference Guide Bosch Security Systems, Inc.