Bosch B6512 User manual

Control Panels
B6512/B5512/B4512/B3512 (B5512E/B4512E/B3512E)
en Installation Manual

Control Panels Table of contents | en 3
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
Table of contents
1Certifications, approvals, listings, and safety 8
1.1 Listings and approvals 8
1.1.1 UL 8
1.1.2 ULC 8
1.1.3 Security Industry Association (SIA) 8
1.1.4 Department of Defense (DoD) 8
1.1.5 Department of Energy 8
1.1.6 California State Fire Marshal (CSFM) 8
1.1.7 National Institute of Standards and Technology (NIST) 8
1.1.8 Federal Communications Commission (FCC) Rules 9
1.1.9 Industry Canada (IC) 9
1.2 Safety 9
1.2.1 Lightning 10
1.2.2 Power 10
2Introduction 12
2.1 About documentation 12
2.1.1 Related documentation 12
2.2 Bosch Security Systems, Inc. product manufacturing dates 14
3System overview 15
4Installation checklist 16
5Control panel installation 18
5.1 Install the enclosure and wiring label 18
5.2 Install the control panel 19
5.2.1 Mount the control panel 19
5.2.2 Connect earth ground 20
5.2.3 Configure OUTPUT A using the jumper 20
5.3 Control panel to module wiring overview 21
6Power supply 22
6.1 Primary (AC) power 22
6.2 Secondary (DC) power 22
6.2.1 Install the battery 22
6.2.2 Battery maintenance 24
6.2.3 Battery supervision 24
6.2.4 Battery discharge and recharge schedule 24
6.3 B520 Auxiliary Power Supply 24
6.3.1 SDI2 address settings 25
6.3.2 Supervision 25
6.3.3 Auxiliary power supply trouble conditions 25
6.3.4 Installation and control panel wiring (B520) 25
6.3.5 Powered device and battery wiring 26
7Telephone communications 28
7.1 B430 Plug-in Telephone Communicator 28
7.1.1 Supervision 28
7.1.2 Installation and module wiring (B430) 28
7.1.3 Diagnostic LEDs 29
7.2 Phone jack location 29
7.3 Telephone line monitor 30
7.4 Called party disconnect 30

4en | Table of contents Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
7.5 Communication failure 31
8IP communications 32
8.1 On-board Ethernet connection 32
8.1.1 Supervision 32
8.1.2 Local RPS programming 32
8.1.3 On-board Ethernet diagnostic LEDs 33
8.2 Conettix Plug-in Cellular Communicators 34
8.2.1 Supervision 34
8.2.2 Installation and module wiring (B44x) 34
8.2.3 Signal strength and diagnostic LEDs 35
8.3 B426 Ethernet Communication Module 36
8.3.1 Address and emulation settings 36
8.3.2 Supervision 36
8.3.3 B426 module faults 36
8.3.4 Local RPS programming 37
8.3.5 Installation and control panel wiring (B426) 37
8.3.6 Diagnostic LEDs 38
8.4 B450 Conettix Plug-in Communicator Interface 40
8.4.1 SDI2 address settings 40
8.4.2 Supervision 40
8.4.3 Installation and control panel wiring (B450) 40
8.4.4 Diagnostic LEDs 41
8.5 Compatible receivers for IP communication 42
9Keypads, keyswitches, keyfobs and transmitters 44
9.1 Keypads 44
9.1.1 B915 Basic Keypad 44
9.1.2 B920 Two-line Alphanumeric Keypad 44
9.1.3 B921C Two-line Capacitive Keypad with Inputs 44
9.1.4 B930 ATM Style Alphanumeric Keypad 44
9.1.5 B942 Touch Screen Keypad 44
9.1.6 Shortcuts and custom functions 45
9.1.7 Address settings 45
9.1.8 Supervision 45
9.1.9 Installation and control panel wiring (keypads) 45
9.1.10 Sensor loops overview and wiring (B921C/B942/B942W only) 46
9.1.11 Output wiring (B942/B942W only) 47
9.1.12 Troubleshooting 47
9.2 Keyswitches 47
9.2.1 Operation 47
9.2.2 Installation and control panel wiring (keyswitches) 48
9.3 RADION keyfobs and Inovonics pendant transmitters 48
10 On-board outputs 50
10.1 Circuit protection 50
10.2 Total available power 50
10.3 Open collector outputs 50
10.4 Continuous power outputs 51
11 Off-board outputs 52
11.1 B308 Octo-output Module 52
11.1.1 SDI2 address settings 52

Control Panels Table of contents | en 5
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
11.1.2 Supervision 52
11.1.3 Installation and control panel wiring (B308) 53
12 On-board points 54
12.1 Point sensor loops 54
12.1.1 Single EOL (and no EOL) resistor circuit style 54
12.1.2 Dual EOL resistor circuit style 55
12.2 Point response time 56
13 Off-board points 57
13.1 B208 Octo-input Module 57
13.1.1 SDI2 address settings 57
13.1.2 Supervision 57
13.1.3 Installation and control panel wiring (B208) 57
13.1.4 Sensor loops overview and wiring 58
13.2 Test off-board points 61
13.3 Extra Point events 61
13.4 Missing point conditions 61
14 Wireless modules 62
14.1 B810 receiver 62
14.1.1 SDI2 address settings 62
14.1.2 Supervision 62
14.1.3 Installation and control panel wiring (B810) 62
14.2 B820 SDI2 Inovonics Interface Module 63
14.2.1 SDI2 address settings 63
14.2.2 Supervision 63
14.2.3 Installation and control panel wiring (B820) 63
15 Access control 65
15.1 B901 65
15.1.1 Address settings 65
15.1.2 Supervision 65
15.1.3 Installation and control panel wiring (B901) 65
15.2 Card reader wiring 66
16 Program and test the control panel 67
16.1 Program the control panel 67
16.2 Perform walk tests 67
16.2.1 Fire walk test 67
16.2.2 Intrusion walk test 67
16.2.3 Service walk test 68
16.2.4 Invisible walk test 68
17 Control panel board overview 70
18 System wiring diagrams 72
18.1 System wiring overview 72
18.2 Battery lead supervision wiring 74
18.3 2-wire smoke wiring (B201) 75
18.4 2-wire smoke wiring (D125B) 76
18.5 Notification appliance circuit wiring 76
18.6 SDI2 devices general system wiring 78
18.6.1 SDI2 bus wiring recommendations 78
18.7 Wiring label 81
19 Approved applications 82

6en | Table of contents Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
19.1 Optional compatible equipment 82
19.1.1 Burglar applications 82
19.1.2 Bank safe and vault applications 82
19.1.3 Fire applications 85
19.1.4 Enclosures 86
19.2 Combination fire and intrusion alarm systems 87
19.3 Compatible UL listed components 87
19.4 Standby battery requirements and calculations 89
19.4.1 Household Fire Warning equipment 91
19.5 UL 365 - Police Station Connected Burglar Alarm Units and Systems 92
19.6 UL 636 - Holdup Alarm Units and System 92
19.7 Required values to achieve 180s (ULC)/200s (UL) supervision interval 92
19.8 ULC 93
20 Keypad Installer menu 94
20.1 [1] Program menu (Programming) 100
20.1.1 [1] Reporting > [1] Phone menu parameters 100
20.1.2 [1] Reporting > [2] Network menu parameters 101
20.1.3 [1] Reporting > [3] Routing menu parameters 102
20.1.4 [1] Reporting > [4] Personal Note menu parameters 103
20.1.5 [2] Network > [1] Ethernet > (choose the bus module or on-board) > [1] Module
Parameters menu
104
20.1.6 [2] Network > [1] Ethernet > (choose the bus module or on-board) > [2] Address
Parameters menu
105
20.1.7 [2] Network > [1] Ethernet > (choose the bus module or on-board) > [3] DNS
Parameters menu
106
20.1.8 [2] Network > [2] Cellular > (choose the SDI2 cellular module or plug-in module) 106
20.1.9 [3] RPS > [1] RPS Passcode menu parameters 107
20.1.10 [3] RPS > [2] RPS Phone Number menu parameters 108
20.1.11 [3] RPS > [3] RPS IP Address menu parameters 108
20.1.12 [3] RPS > [4] RPS Port Number menu parameters 108
20.1.13 [4] Area Options menu parameters 108
20.1.14 [5] Keypad menu parameters 110
20.1.15 [6] Users menu parameters 111
20.1.16 [7] Points menu parameters 112
20.1.17 [8] Disable Programming menu 118
20.2 [2] Wireless menu 119
20.2.1 [1] RF Point Menu> [1] Enroll Point RFID 119
20.2.2 [1] RF Point Menu> [2] Replace Point RFID 119
20.2.3 [1] RF Point Menu> [3] Remove Point RFID 119
20.2.4 [2] RF Repeater Menu > [1] Add Repeater 120
20.2.5 [2] RF Repeater Menu > [2] Replace Repeater 120
20.2.6 [2] RF Repeater Menu > [3] Remove Repeater 120
20.2.7 [3] RF Diagnostic Menu > [1] RF Points 120
20.2.8 [3] RF Diagnostic Menu > [2] RF Repeater Menu 121
20.3 [3] Diags menu 121
20.3.1 [1] Wireless 121
20.3.2 [2] Network menu 122
20.3.3 [3] Cellular menu 122
20.3.4 [4] IP Camera 122

Control Panels Table of contents | en 7
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
20.3.5 [5] Cloud 123
20.4 [4] Service Bypass (Serv Byp) menu 123
20.5 [5] Versions menu 123
20.6 [6] Cloud menu 124
21 Specifications 125
21.1 Wire requirements 127
22 Appendix 128
22.1 Address settings 128
22.1.1 B208 address settings 128
22.1.2 B308 address settings 128
22.1.3 B901 address settings 129
22.1.4 B91x address settings 129
22.2 Reporting and device number information 130
22.2.1 Report format definitions 130
22.2.2 SDI2 address information 139
22.2.3 Device numbers (zzz, dddd) 139
22.2.4 Communication Trouble device numbers (zzzz) 140
22.2.5 Special User IDs (uuuu, iiii) 140
22.2.6 Keypad alarm virtual point numbers (ppp, pppp) 140
22.3 AutoIP 141

8en | Certifications, approvals, listings, and safety Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
1 Certifications, approvals, listings, and safety
This section provides certification and approval listings and safety information.
1.1 Listings and approvals
This document includes the section Approved applications, page 82. Refer to this section for
guidelines on installing the control panels in Underwriters Laboratories Inc. (UL) and fire-
specific applications.
1.1.1 UL
Listed for:
– UL 365 - Police Station Connected Burglar Alarm Units and System
– UL 609 - Local Burglar Alarm Units and System
– UL 636 - Holdup Alarm Units and System
– UL 985 - Household Fire Warning System Units
– UL 1023 - Household Burglar Alarm Units and System
– UL 1076 - Proprietary Burglar Alarm Units and System
– UL 1610 - Central Station Burglar Alarm Units
– UL 1635 - Digital Alarm Communicator System Units
1.1.2 ULC
Listed for:
– ULC C1023 - Household Burglar Alarm System Units
– ULC C1076 - Proprietary Burglar Alarm Units and System
– ULC S303 - Local Burglar Alarm Units and System
– ULC S304 - Central and Monitoring Station Burglar Alarm Units
– ULC S545 - Residential Fire Warning System Control Units
– ULC S559 – Fire Signal Receiving Centres and Systems
1.1.3 Security Industry Association (SIA)
Listed for Control Panel Standard - Features for False Alarm Reduction ANSI/SIA CP-01-2010.
1.1.4 Department of Defense (DoD)
The B6512/B5512/B4512/B3512 control panels were granted approval for Department of
Defense (DoD) installations in Sensitive Compartmented Information Facilities (SCIF).
1.1.5 Department of Energy
This control panel operates on a transformer that has been reviewed by a third party and
deemed to be compliant to the Department of Energy, U.S. Energy Conservation Standard for
External Power Supplies (found in section 10 CFR 430.32(w)(1)(i) of the Federal Code) as an
indirect device.
1.1.6 California State Fire Marshal (CSFM)
Listed for Household Fire Alarm.
1.1.7 National Institute of Standards and Technology (NIST)
When communicating via a network, listed for Advanced Encryption Standard (AES), Federal
Information Processing Standards Publication 197 (FIPS 197).

Control Panels Certifications, approvals, listings, and safety | en 9
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
1.1.8 Federal Communications Commission (FCC) Rules
Part 15
This equipment was tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy; and if not installed
and used according to the instructions, can cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user is required to correct the interference at his or her own expense.
Part 68
The B430 module by Bosch Security Systems, Inc. is registered with the Federal
Communication Commission (FCC) under Part 68, for connection to the public telephone
system using an RJ31X or RJ38X phone line connection jack installed by the local telephone
company.
Do not connect registered equipment to party lines or coin-operated telephones. Notify the
local telephone company and provide the following information before connecting the control
panel to the telephone network:
– The particular line to which you connect the module
– Make (Bosch Security Systems, Inc.), model (B6512/B5512/B4512/B3512), and serial
number of the control panel
– FCC registration number: ESVAL00BB430
– Ringer eq: 0.0B
1.1.9 Industry Canada (IC)
ICES-003 - Information Technology Equipment
This Class B digital equipment meets all requirements of the Canadian interference-causing
equipment regulations.
Cet appareil numérique de la Class A respecte toutes les exifences de règlement sue le
matériel brouilleur du Canada.
CS-03 - Compliance Specification for Terminal Equipment
The B430 module by Bosch Security Systems, Inc. meets the applicable Industry Canada
technical specifications. The Ringer Equivalence Number (REN) is an indication of the
maximum number of devices allowed to be connected to a telephone interface. The
termination of an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices not exceed five.
Le présent matériel est conforme aux spécifications techniques applicables d'Industrie
Canada.
L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui
peuvent être raccordés à une interface téléphonique. La terminaison d'une interface peut
consister en une combinaison quelconque de dispositifs, à la seule condition que la somme
d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas cinq.
1.2 Safety
Notice!
After system installation and any control panel programming, perform a complete system test.
A complete system test includes testing the control panel, all devices, and communication
destinations for proper operation.

10 en | Certifications, approvals, listings, and safety Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
1.2.1 Lightning
The control panel design significantly reduces the adverse effects of lightning. Taking
installation precautions can further reduce these adverse effects.
Effects of lighting
Electronics involved in a direct lightning strike or near a lightning strike can show adverse
effects. When lightning strikes, several things happen:
– An electromagnetic wave spreads from the center point of the strike inducing high
voltages onto nearby conductors.
– The voltage changes substantially on electrical grounds near the lightning strike.
– High voltages are induced onto anything directly struck by lightning.
The effects of lightning can include trouble events, alarm events, and physical damage.
Installation precautions
To minimize the undesirable effects from lightning:
– Do not run wiring outside the building.
– If you install the unit in a metal building, keep the wiring at least 2 ft (0.61 m) away from
external metal surfaces. Make a proper earth ground connection.
– Earth ground the unit correctly. Do not use an electrical ground or telephone ground.
– Avoid running wires near telephone, data, or power lines. Locating control panel wiring at
least 2 ft (0.61 m) away helps reduce the effects of lightning.
– When your data lines must cross the path of AC or other wiring, cross perpendicular to
the lines.
Warranty regarding lightning
The warranty does not cover physical damage due to lightning.
1.2.2 Power
!
Caution!
Remove all power (AC and battery) before making any connections. Failure to do so might
result in personal injury and/or equipment damage.
!
Caution!
Do not short-circuit the terminals of the transformer: Shorting the terminals opens the
internal fuse, causing permanent failure. Connect the transformer to the control panel’s AC
power terminals before plugging it into the power source.
Notice!
Plan ahead
Route telephone, SDI2 bus wiring, and sensor loop wiring away from any AC conductors,
including the transformer wire. AC wiring can induce noise and low level voltage into adjacent
wiring.
!
Warning!
High current arcs are possible. The positive (red) battery lead and the terminal labeled BAT+
can create high current arcs if shorted to other terminals or the enclosure. Use caution when
working with the positive lead and the terminal labeled BAT+. Always disconnect the positive
(red) lead from the battery before removing it from the terminal labeled BAT+.

Control Panels Certifications, approvals, listings, and safety | en 11
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
!
Caution!
The battery terminals and wire are not power limited. Maintain a 0.250 in (6.4 mm) space
between the battery terminals, battery wiring, and all other wiring. Battery wiring cannot
share the same conduit, conduit fittings, or conduit knockouts with other wiring.
!
Caution!
Exceeding the maximum output ratings or installing the transformer in an outlet that is
routinely switched off causes heavy discharges. Routine heavy discharges can lead to
premature battery failure.
Notice!
Use sealed lead acid batteries only
The charging circuit is calibrated for lead-acid batteries. Do not use gel-cell or NiCad
batteries.

12 en | Introduction Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
2 Introduction
This section includes an introduction to documents for this product and other document-
related instructions.
2.1 About documentation
This document contains instructions for a trained installer to properly install, configure, and
operate this control panel, and optional peripheral devices. Review this document before
beginning the installation to determine the hardware and wiring requirements for the features
used.
(Bosch Security Systems, Inc. recommends that installers follow good wiring practices such as
those described in NFPA 731, Standard for the Installation of Electronics Premises Security
Systems.)
Throughout this document, the words “control panel” refer to all control panels covered by
this document (B6512/B5512/B5512E/B4512/B4512E/B3512/B3512E).
Notifications
This document uses Notices, Cautions, and Warnings to draw your attention to important
information.
Notice!
These include important notes for successful operation and programming of equipment, or
indicate a risk of damage to the equipment or environment.
!
Caution!
These indicate a hazardous situation which, if not avoided, could result in minor or moderate
injury.
!
Warning!
These indicate a hazardous situation which, if not avoided, could result in death or serious
injury.
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
2.1.1 Related documentation
Control panel documents
Control Panels (B5512/B4512/B3512) Release Notes*
Control Panels (B5512/B4512/B3512) Installation and System Reference Guide (this document)
(P/N: F01U287180)+
Control Panels (B9512G/B8512G/B5512/B4512/B3512) Owner’s Manual (P/N: F01U287181)* +
Control Panels (B5512/B4512/B3512) Program Entry Guide (P/N: F01U287183)+

Control Panels Introduction | en 13
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
Control Panels (B5512/B4512/B3512) UL Installation Guide (P/N: F01U287185)* +
Control Panels (B5512/B4512/B3512) SIA Quick Reference Guide (P/N: F01U287184)* +
Control Panels (B9512G/B8512G/B6512/B5512/B4512/B3512) ULC Installation Guide (P/N:
F01U321698)*
*Shipped with the control panel.
+Located on the documentation CD shipped with the control panel.
Keypad documents
Basic Keypad (B915) Installation Guide (P/N: F01U297873)*
Two-line Alphanumeric Keypad (B920) Installation Guide (P/N: F01U265450)*
Two-line Capacitive Keypad with Inputs (B921C) Installation Guide (P/N: F01U297887)*
ATM Style Alphanumeric Keypad (B930) Installation Guide (P/N: F01U265451)*
Touch Screen Keypad (B942/B942W) Installation Guide (P/N: F01U294527)*
*Shipped with the keypad.
Optional module documents
2-wire Powered Loop Module (B201) Installation and Operation Guide (P/N: F01U301248)*
Octo-input Module (B208) Installation and Operation Guide (P/N: F01U265456)*
Octo-output Module (B308) Installation and Operation Guide (P/N: F01U265458)*
Conettix Ethernet Communication Module (B426) Installation and Operation Guide (P/N:
F01U281208)* +
Plug-in Telephone Communicator (B430) Installation Guide Installation Guide (P/N:
F01U265454)*
Conettix Plug-in Cellular Communicator (B440) Installation and Operation Guide (P/N:
F01U265455)*
Conettix Plug-in CDMA Cellular Communicator (B441) Installation and Operation Guide (P/N:
F01U282233)*
Conettix Plug-in GPRS Cellular Communicator (B442) Installation and Operation Guide (P/N:
F01U283180)*
Conettix Plug-in HSPA+ Cellular Communicator (B443) Installation and Operation Guide (P/N:
F01U283181)*
Conettix Plug-in Communicator Interface (B450) Installation and Operation Guide (P/N:
F01U300740)* +
Auxiliary Power Supply (B520) Installation and Operation Guide (P/N: F01U265445)*
RADION receiver SD (B810) Installation Guide (P/N: F01U261834)*
SDI2 Inovonics Interface Module (B820) Installation Guide (P/N: F01U265460)*
*Shipped with the module.
+Located on the documentation CD shipped with the module.

14 en | Introduction Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
2.2 Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems,
Inc. website at http://www.boschsecurity.com/datecodes/.
The following image shows an example of a product label and highlights where to find the
manufacturing date within the serial number.

Control Panels System overview | en 15
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
3 System overview
B430
Plug-in Telephone Communicator
provides a single
telephone RJ-45 connector
to allow communication
over telephone lines.
Control
Panel
On-board Points
1 to 8
B44x
Conettix Plug-In Cellular
Communicator allows
communication over
a cellular network.
B208
Octo-input modules allow
the addition of up to 8
input devices.
B308
Octo-output modules allow
the addition of up to 8
output devices.
B520
Auxiliary Power Supply modules
expand power by connecting to
an SDI2 device bus or
other 12 volt devices.
B810
RADION receiver SDs
connect RADION wireless devices
to the control panel.
B820
SDI2 Inovonics Interface modules
interface with an Inovonics
wireless receiver.
B91x/B92x/B93x/B94x
Use keypads to operate
the control panel by area.
B5512 control panels support up to 4 areas.
B4512 control panels support up to 2 areas.
B3512 control panels support 1 area.
Each area can have its own account number
or you can group together areas
with a common account number.
B450
Conettix Plug-In Communicator
Interface allows communication
over a cellular network through
the SDI2 bus.
B426
The B426 provides off-board
communication over a network.

16 en | Installation checklist Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
4 Installation checklist
Before installing and operating the control panel, read these instructions. If you do not read
and understand these explanations, you will not be able to install and operate the device
properly. The instructions do not eliminate the need for training by authorized personnel.
Install, operate, test and maintain this device according to the control panel Installation and
System Reference Guide (this document). Failure to follow these procedures may cause the
device not to function properly. Bosch Security Systems Inc. is not responsible for any devices
that are improperly installed, tested or maintained.
The control panel Installation and System Reference Guide (this document) does not contain
special information about local requirements and safety issues. Information on such issues is
provided only to the extent that it is needed for operation of the device. Ensure that you are
familiar with all safety-related processes and regulations in your area. This also includes how
to act in the event of an alarm and the initial steps to take if a fire breaks out. The operating
instructions should always be available on site. It is a required part of the system and must be
given to the new owner if the system is ever sold.
Use the workflow and checkboxes below as you complete steps. Each step includes
references for more detailed information.
Install the enclosure and wiring label
–Install the enclosure and wiring label, page 18
Install the control panel
–Mount the control panel, page 19
–Connect earth ground, page 20
–Configure OUTPUT A using the jumper, page 20
Install and wire for telephone communication
–Telephone communications, page 28
Install and wire for IP communications
–IP communications, page 32
Install and wire the battery and the transformer
–Power supply, page 22
Begin to charge the battery while you install other devices
– Charge the battery
Install and wire arming devices
–Keypads, keyswitches, keyfobs and transmitters, page 44
Install and wire outputs
–On-board outputs, page 50
–Off-board outputs, page 52
Install and wire inputs
–On-board points, page 54
–Off-board points, page 57
–Wireless modules, page 62

Control Panels Installation checklist | en 17
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
Complete the installation
–Program and test the control panel, page 67

18 en | Control panel installation Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
5 Control panel installation
This section explains how to mount the control panel enclosure, how to mount the control
panel into the enclosure, and provides an overview of how to wire modules to the control
panel.
5.1 Install the enclosure and wiring label
Refer to Enclosures, page 86 to determine if the application requires a specific enclosure.
Installing the enclosure:
1. Remove any knockouts prior to installing the control panel.
2. Mount the enclosure in the desired location. Use all enclosure mounting holes. Refer to
the mounting instructions supplied with the selected enclosure.
3. Pull the wires into the enclosure.
4. Install the supplied Enclosure Wiring Label (B5512/B4512/B3512) on the inside of the
enclosure door.
Notice!
Electromagnetic interference (EMI) can cause problems on long wire runs.
1 2 3
4
22 5
2
3
Figure5.1: Enclosure and control panel mounting (B10 shown)
Callout ᅳ Description
1 ᅳ Control panel wiring label
2 ᅳ Enclosure mounting holes (4)
3 ᅳ Module mounting locations (4)

Control Panels Control panel installation | en 19
Bosch Security Systems, Inc. Installation Manual 2017.04 | 15 | F.01U.287.180
4 ᅳ Tamper switch mounting location
5 ᅳ Control panel mounting location
5.2 Install the control panel
This section includes instructions to mount the control panel in the enclosure, connect earth
ground, and make other control panel connections.
5.2.1 Mount the control panel
1. Identify the control panel mounting location in the enclosure.
2
3
3
Figure5.2: B10 and B11 control panel placement locations
Callout ᅳ Description
1 ᅳ B10 Medium Control Panel Enclosure
2 ᅳ B11 Small Control Panel Enclosure
3 ᅳ Mounting clip locations for the control panel
2. Snap the four supplied plastic standoffs onto four enclosure support posts. If using the
B12 Mounting Plate for D8103 Enclosure, attach the standoffs to the plate support posts.
Do not attach the standoffs with screws at this time.
Figure5.3: Standoff attachment

20 en | Control panel installation Control Panels
2017.04 | 15 | F.01U.287.180 Installation Manual Bosch Security Systems, Inc.
3. Place the control panel on top of the standoffs. Align the holes in the corners of the
control panel with the openings at the top of each standoff. Secure the control panel to
the standoffs with supplied, self-threading screws.
Figure5.4: Mount control panel on standoffs
4. If using the B12 Mounting Plate for D8103 Enclosure, rest the hook tabs on the mounting
plate hooks within the enclosure. Secure the lock-down tab to the plate mounting hole
with the screw provided.
5.2.2 Connect earth ground
5.2.3 Configure OUTPUT A using the jumper
When planning your installation, carefully consider the use of OUTPUT A. OUTPUT A is a form
C relay. You can configure the common terminal (C) of Output A (OUTPUT A) using the
jumper:
– To provide +12 VDC (AUX power)
– To be a COM terminal (parallel to all COM terminals)
– To be a dry contact (no voltage, not common)
The control panel ships with the jumper in the default position, AUX power. (OUTPUT A, ‘C’
terminal providing AUX PWR). To reconfigure the ‘C’ terminal as a COM terminal (parallel to all
COM terminals), remove the door covering the jumper pins, and move the jumper to the left
two pins. The OUTPUT A LED lights when OUTPUT A is active. Refer to the figure below or to
the Enclosure Wiring Label (B5512/B4512/B3512) to set the OUTPUT A jumper.
P1
P1
P1
OUTPUT A (C terminal) = AUX PWR
COM AUX
OUTPUT A (C terminal) = COM
OUTPUT A (C terminal) = DRY
COM AUX
COM AUX
COM AUX
P1
TMPR
1 COM 2 7 COM 83 COM 4 5 COM 6
RESET ETHERNET
COM AUX R Y G B
PWR A B COM
+ BAT -18VAC
B C
OUTPUT
NO C NC
OUTPUT A
7 COM 8
C
OUTPUT
B
USB
ETHERNET
100BASE-T
LINK
COMMUNICATION MODULE 1
1 k End of Line Resistors
Voltage Ranges
ON-BOARD POINTS
3.7 - 5.0 VDC
2.0 - 3.0 VDC
0.0 - 1.3 VDC
Open
Normal
Short
3 COM 4 5 COM 61 COM 2
R Y G B
SDI2
Device Bus
18 VAC OUTPUT A
AUX
- 12 V +
Figure5.5: OUTPUT A jumper configuration options (B5512 shown)