Bosch D9412GV3 Quick start guide

EN
Operation and Installation Guide
Control Panels
D9412GV3/D7412GV3

D9412GV3/D7412GV3 |Operation and Installation Guide | Trademarks
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 2
Trademarks
CoBox is a registered trademark of Lantronix.
Windows is a registered trademark of Microsoft
Corporation in the United States or in other countries.
Molex is a registered trademark of Molex
Incorporated.
Certifications and Approvals
The D9412GV3/D7412GV3 Literature Pack includes
the D9412GV3/D7412GV3 Approved Applications
Compliance Guide (P/N: F01U143069). Refer to this
guide for additional guidelines on installing the control
panels in Underwriters Laboratories Inc. (UL) and fire-
specific applications.
Listings and Approvals
UL
The D9412GV3 and D7412GV3 Control Panels are
UL Listed for Central Station, Local, Auxiliary,
Proprietary, and Household Fire Alarm, and Central
Station, Local, Police Station Connect, Household
Burglar Alarm and Encrypted line Security when
communicating via a network.
Department of Defense (DOD)
The D9412GV3/D7412GV3 was granted approval for
Department of Defense (DoD) installations in
Sensitive Compartmented Information Facilities
(SCIF).
Federal Communications
Commission (FCC) Rules
Part 15
This equipment was tested and found to comply with
the limits for a Class A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy; and if not installed and used
according to the instructions, can cause harmful
interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user is required to correct the interference at his or
her own expense.
Part 68
This equipment complies with Part 68 of FCC rules. A
label contains, among other information, the FCC
registration number and ringer equivalence number
(REN). If requested, this information must be provided
to the telephone company.
The D9412GV3 and D7412GV3 Control Panels are
registered for connection to the public telephone
network using an RJ38X or RJ31X jack.
The REN is used to determine the number of devices
that can be connected to the telephone line.
Excessive RENs on the telephone line may result in
the devices not ringing in response to an incoming
call. In most, but not all areas, the sum of the RENs
should not exceed five. To be certain of the number of
devices that may be connected to the line, as
determined by the RENs, contact the telephone
company to determine the maximum REN for the
calling area.
If you experience trouble with the control panel,
please contact Bosch Security Systems Customer
Service for repair and warranty information. If the
trouble is causing harm to the telephone network, the
telephone company might request that the equipment
be removed from the network until the problem is
resolved. User repairs must not be made, and doing
so will void the user’s warranty.
If the D9412GV3 or D7412GV3 Control Panel causes
harm to the telephone network, the telephone
company attempts to notify you in advance. If
advance notice is not practical, the telephone
company notifies you as soon as possible. Also, you
will be advised of your right to file a complaint with the
FCC if you believe it is necessary.

D9412GV3/D7412GV3 |Operation and Installation Guide | Federal Communications Commission (FCC) Rules
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 3
The telephone company might make changes in its
facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this
happens, the telephone company provides advance
notice in order for the necessary modifications to be
made in order to maintain uninterrupted service.
This equipment cannot be used on public coin service
provided by the telephone company. Connection to
Party Line service is subject to state tariffs. (Contact
your state public utilities commission for information.)
FCC Registration Number:
US:ESVOT00BD9412GV3
Service Center in USA:
Bosch ST Service Center
8601 East Cornhusker Hwy
Dock B
Lincoln, NE 68507 - 9702 USA
Ringer Equivalence: 0.0B

D9412GV3/D7412GV3 |Operation and Installation Guide | Contents
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 4
Contents
1.0 Introduction ......................................................7
2.0 Lightning Strikes .............................................8
2.1 Effects .................................................................8
2.2 Precautions during Installation ........................8
3.0 Overview............................................................9
3.1 Configuration and Parts....................................9
3.1.1 Parts List...........................................................10
3.1.2 Parts Available by Separate Order ...............10
3.2 Accessories ......................................................11
3.3 Features in the D9412GV3 and D7412GV3 12
3.3.1 SDI Molex Connector......................................12
3.3.2 Tip and Ring Posts ..........................................12
3.3.3 Telephone Line Sniff .......................................12
3.3.4 Points ................................................................12
3.3.5 Areas and Accounts ........................................12
3.3.6 Digital Communicator......................................12
3.3.7 Keypads ............................................................13
3.3.8 Keyswitch..........................................................13
3.3.9 Access Control.................................................13
3.3.10 Event Memory..................................................13
3.3.11 Event Log..........................................................13
3.3.12 Ground Fault Detection ..................................13
3.3.13 Ground Fault Detection Added Feature .......14
3.3.14 Conettix Functions...........................................14
3.3.15 Programming....................................................14
3.3.16 Other Features.................................................14
4.0 Installation.......................................................14
4.1 Installation Preparation...................................14
4.2 Enclosure Options ...........................................14
4.3 Mounting Enclosure ........................................14
4.4 Installing the Control Panel ............................15
4.5 Connecting Earth Ground...............................15
4.5.1 Terminal 10.......................................................15
4.5.2 Ground Fault Detect Enable ..........................15
4.5.3 Enabling Ground Fault Detection..................16
4.5.4 Ground Fault Specifications...........................16
4.5.5 Locking the Reset Pin.....................................16
4.6 Completing the Installation.............................17
4.6.1 Charging the Battery .......................................17
4.6.2 Installing and Wiring Detection Devices.......17
4.6.3 Installing Modules and Relays.......................17
4.6.4 Connecting the On-board Points and
Keypads ............................................................17
4.6.5 Powering Up.....................................................17
4.7 Programming the Control Panel....................17
4.8 Installing the Point Chart Label .....................18
4.9 Testing the System .........................................18
4.10 Service Walk Test ...........................................18
5.0 Power Supply .................................................22
5.1 Primary Power Terminals 1 and 2 ................22
5.1.1 Primary (AC) Power Circuit............................22
5.1.2 Installing the Transformer ..............................22
5.2 Secondary Power Terminals .........................22
5.2.1 Secondary (DC) Power ..................................22
5.2.2 Installing the Battery........................................22
5.2.3 Replacing the Battery .....................................24
5.2.4 Battery Supervision.........................................24
5.2.5 Battery Charging Circuit .................................24
5.2.6 Battery Discharge and Recharge Schedule 25
6.0 Power Outputs ...............................................26
6.1 Circuit Protection .............................................26
6.2 Total Available Power.....................................26
6.3 Continuous Power Output Terminals 3, 8, 24,
and 32 ...............................................................26
6.4 Programmable Power Output Terminals 6, 7,
and 8 .................................................................27
6.4.1 Programming ...................................................27
6.4.2 Terminals 6 and 7 ...........................................27
6.4.3 Fire System Power Formula ..........................27
6.4.4 Terminal 8.........................................................27
7.0 Telephone Connections ..............................28
7.1 Registration ......................................................28
7.2 Notification........................................................28
7.3 Location ............................................................28
7.4 Telephone Cord Connection..........................28
7.5 Phone LED (Red)............................................29
7.6 Operation Monitor LED (Green)....................29
7.7 Dialing Format .................................................29
7.8 Telephone Line Monitor..................................29
7.9 Called Party Disconnect.................................29
7.10 Communication Failure ..................................29
7.11 D928 Dual Phone Line Switcher...................30
7.11.1 Description .......................................................30
7.11.2 Operation..........................................................30
7.11.3 Installing the D928 ..........................................31
7.11.4 D928 Status LEDs...........................................31
8.0 On-Board Points............................................31
8.1 Terminals 11 to 22 Description .....................31
8.2 Point Sensor Loops.........................................31
8.3 Point Parameters.............................................32
8.4 Point Response Time .....................................33

D9412GV3/D7412GV3 |Operation and Installation Guide | Contents
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 5
8.5 Wiring Information for Installations Using the
Rothenbuhler 5110/4001-42 High Security
Bell.....................................................................33
9.0 Off-Board Points............................................36
9.1 Point (Zonex) Bus: D9412GV3 Terminals and
D7412GV3 Terminals .....................................36
9.1.1 POPIT Modules................................................36
9.1.2 POPEX Modules..............................................36
9.1.3 Missing Conditions ..........................................36
9.1.4 Extra Point Events...........................................36
9.1.5 D9412GV3/D7412GV3 Responses to Missing
Point Conditions...............................................37
9.2 D8125 and D9127 POPIT Modules ..............37
9.3 Installing the D8125 POPEX Module............40
9.3.1 Mounting ...........................................................40
9.3.2 Wiring the D8125 to the Control Panel.........40
9.3.3 Wiring POPITs to the Data Expansion Loop40
9.3.4 Wiring Data Expansion Loops to POPEX
Modules.............................................................41
9.3.5 POPIT Sensor Loops ......................................41
9.3.6 POPIT Module Point Assignments................41
9.3.7 Program Record Sheet...................................41
9.3.8 POPIT Labels...................................................42
9.4 D8128D OctoPOPIT Module .........................42
9.4.1 Description........................................................42
9.4.2 Listings ..............................................................43
9.4.3 Installation.........................................................44
9.4.4 Setting the OctoPOPIT Switches ..................44
9.4.5 Mounting OctoPOPITs....................................45
9.4.6 Wiring OctoPOPITs.........................................45
9.4.7 OctoPOPIT Sensor Loops..............................49
9.5 Testing Off-Board Points ................................49
10.0 Off-Board Relays.................................................50
10.1 D8129 OctoRelay ............................................50
10.1.1 Configuring the D8129 OctoRelay ................51
10.1.2 Relay Outputs ..................................................51
10.1.3 Installation.........................................................51
10.1.4 Wiring Connections .........................................52
10.2 D811 Arm Status Relay Module....................52
10.2.1 Relay Output ....................................................52
10.2.2 Installation.........................................................52
10.2.3 Wiring Connections .........................................53
11.0 Arming Devices ...................................................55
11.1 Description........................................................55
11.2 Keypad Terminals 29 to 32 ............................55
11.2.1 Assigning an Address for the Keypad ..........55
11.2.2 Installation.........................................................56
11.3 D279A Independent Zone Control................57
11.4 Keyswitch .........................................................57
11.4.1 Description .......................................................57
11.4.2 Programming ...................................................57
11.4.3 Installation ........................................................57
11.4.4 Operation..........................................................57
12.0 SDI Devices ..........................................................59
12.1 Description .......................................................59
12.2 Installation ........................................................59
12.3 D9131A Parallel Printer Interface Module ...59
12.3.1 Switch Settings ................................................59
12.3.2 Supervision.......................................................59
12.4 D9210B Wiegand Control Interface Module 60
12.4.1 Access ..............................................................60
12.4.2 Switch Settings ................................................60
12.5 SDI Addresses 88 and 92..............................60
12.5.1 D9133DC Direct Connect Programming
Module ..............................................................60
12.5.2 Network Interface Modules ............................61
12.5.3 Address Settings .............................................61
12.5.4 Supervision.......................................................61
13.0 Programmer and Accessory Connections...62
13.1 Programmer Connector..................................62
13.2 Installer Keypad and Local Programmers
Mode .................................................................62
13.3 Programmer Access Reports ........................62
13.4 Accessory Connector......................................63
14.0 Faceplates ............................................................64
14.1 D9412GV3 Faceplate .....................................64
14.2 D7412GV3 Faceplate .....................................65
Appendix A: System Wiring Diagrams, Issue A..66
A.1 D9412GV3 Control Panel ..............................66
A.2 D7412GV3 Control Panel ..............................69
Appendix B: Point Address Charts ........................72
B.1 Zonex 1, Points 9 to 127 (D9412GV3); Zonex
1, Points 9 to 75 (D7412GV3) .......................72
B.2 Zonex 2, Points 129 to 247 (D9412GV3 Only)
...........................................................................73
Specifications...............................................................74
SDI Bus A (+): ................................................................74
Connection: ....................................................................74
Two Telco lines:.............................................................74
Discharge Cycle.............................................................74

D9412GV3/D7412GV3 |Operation and Installation Guide | Tables
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 6
Figures
Figure 1: System Configuration ................................9
Figure 2: Enclosure Mounting .................................15
Figure 3: Enabling Ground Fault Detection...........16
Figure 4: Reset Pin ...................................................16
Figure 5: D9412GV3 Service Walk Test Flow Chart
....................................................................20
Figure 6: D7412GV3 Service Walk Test Flow Chart
....................................................................21
Figure 7: Battery Terminals .....................................23
Figure 8: Non-Power-Limited Wiring ......................23
Figure 9: Charging and Battery LEDs ....................24
Figure 10: RJ31X Wiring ............................................28
Figure 11: Phone Connector, Phone LED, and
Operation Monitor LED Locations..........28
Figure 12: D928 Dual Phone Line Switcher ............30
Figure 13: On-board Point Sensor Loop Wiring......32
Figure 14: Rothenbuhler 5110/4001-42 High
Security Bell Wiring Configuration .........34
Figure 15: Wiring the Rothenbuhler 5110/4001-42
High Security Bell to the D9412GV3 or
D7412GV3 Control Panel........................35
Figure 16: Connecting the D8125 POPEX to the
D9412GV3 Control Panel........................38
Figure 17: Connecting the D8125 POPEX to the
D7412GV3 Control Panel........................39
Figure 18: Program Record Sheet............................42
Figure 19: D8128D OctoPOPIT Layout ...................43
Figure 20: Connecting D8128D OctoPOPITs to the
D9412GV3.................................................46
Figure 21: Connecting D8128D OctoPOPITs to the
D7412GV3.................................................47
Figure 22: Wiring Multiple D8128Ds Using Molex®
Connectors ................................................48
Figure 23: D8128D OctoPOPIT Sensor Loops.......49
Figure 24: D8129 Connections to the D9412GV3..50
Figure 25: D8129 Connections to the D7412GV3..51
Figure 26: D811 Module Wiring to the D9412GV3.53
Figure 27: D811 Module Wiring to the D7412GV3.54
Figure 28: Power at Keypads ....................................57
Figure 29: Keyswitch Wiring ......................................58
Figure 30: DX4020 DIP Switch Settings ..................61
Figure 31: Reset Pin ...................................................62
Figure 32: Programmer and Accessory Connections
....................................................................63
Figure 33: D9412GV3 Faceplate ..............................64
Figure 34: D7412GV3 Faceplate ..............................65
Figure 35: D9412GV3, Power Supply Side System
Wiring .........................................................66
Figure 36: D9412GV3, Input Points and Peripheral
Devices System Wiring ...........................67
Figure 37: D9412GV3, SDI Devices System Wiring
System Wiring...........................................68
Figure 38: D7412GV3, Power Supply Side System
Wiring.........................................................69
Figure 39: D7412GV3, Input Points and Peripheral
Devices System Wiring ...........................70
Figure 40: D7412GV3, SDI Devices System Wiring
....................................................................71
Tables
Table 1: Related Documentation............................. 7
Table 2: GV3 Series Control Panel Differences ...9
Table 3: Compatible Accessories1........................11
Table 4: Compatible Keypads................................13
Table 5: Ground Fault Impedance Specifications16
Table 6: Battery Discharge and Recharge
Schedule....................................................25
Table 7: Charging Status and Low Battery LEDs25
Table 8: Phone Cord Lengths................................31
Table 9: Point Parameters .....................................32
Table 10: POPEX Modules ......................................36
Table 11: Extra Point Events ...................................36
Table 12: Off-Board Point Errors.............................37
Table 13: Data Expansion Loop Wire Specifications
....................................................................40
Table 14: D8128D OctoPOPIT Switch Settings for
D9412GV3 and D7412GV3 ....................44
Table 15: Switch 5 Settings for Line Termination .44
Table 16: Terminal Strip Connections ....................45
Table 17: D8129 OctoRelay Switch Settings.........51
Table 18: Number of D8128Ds Used with D8129s52
Table 19: Keypad Address Settings........................55
Table 20: Keypad Connections ...............................56
Table 21: SDI Device Connections .........................59
Table 22: Printer Address Switch Settings.............59
Table 23: Address Switch Settings for Access
Control Module .........................................60
Table 24: Zonex 1 Point Address Chart .................72
Table 25: Zonex 2 Point Address Chart .................73
Table 26: Specifications............................................74

D9412GV3/D7412GV3 |Operation and Installation Guide | 1.0 Introduction
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 7
1.0 Introduction
This manual addresses the operation and installation of the D9412GV3 and D7412GV3 Control Panels.
Throughout this guide, the words “control panel” refer to both control panels (D9412GV3 and D7412GV3).
Table 2 on page 9 provides an overview of the differences in the control panels.
To obtain any of the documents in Table 1, contact Bosch Security Systems, Inc. Customer
Service at [phone] and request the documentation by its corresponding part number.
Table 1: Related Documentation
Product Type Name of DocumentationPart Number
D9412GV3/D7412GV3 Release NotesF01U143073
D9412GV3/D7412GV3 Approved Applications Compliance GuideF01U143069
D9412GV3/D7412GV3 Operation and Installation Guide (this document) F01U143070
D9412GV3/D7412GV3 Program Entry GuideF01U170807
D9412GV3/D7412GV3 Program Record SheetF01U170809
Control Panels
UL Certificated Bank Safe and Vault Applications Technogram 73-07302-000
D1255RB/D1256RB/D1257RB Installation InstructionsF01U011791
D1255/D1255B Installation Instructions 74-06819-000
D1256/D1257 Installation Instructions 74-06925-000
D1260/D1260B Installation Guide 48101
D1260/D1260B Owner’s Manual 50410
D720 Series Installation Instructions 74-06918-000
D279A Operation and Installation Instructions 46458
Security System Owner's Manual 71-06633-000
Keypads
GV3 Series Owner's Manual Supplement F01U143082
Programming
Tools
RPS Installation Guide 4998141259
D8128D Installation GuideF01U070537
D8125MUX Operation & Installation GuideF01U034973
ISW-D8125CW-V2 Installation & Operation Guide F01U161691
Expansion
Devices
D9210B Operation and Installation Guide32206
These products meet the requirements for UL 864 Commercial Fire applications.

D9412GV3/D7412GV3 |Operation and Installation Guide | 2.0 Lightning Strikes
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 8
2.0 Lightning Strikes
The control panels are designed to significantly
reduce electromagnetic interference and malfunction
generally caused by lightning.
2.1 Effects
Any electronic system can be struck directly by
lightning or be adversely affected by a lightning strike
near the system. When lightning strikes, several
things happen:
An electromagnetic wave spreads from the point
of the strike inducing high voltages in nearby
conductors.
The voltage changes substantially on electrical
grounds near the lightning strike.
High voltages are induced in anything directly
struck by lightning.
The effects of a lightning strike can include Missing
Trouble, Missing Alarm, or Point Bus Trouble events.
Occasionally, Reboot and Watchdog events might be
sent because the control panel tried to reset itself.
Electronic systems, including control panels, cannot
be completely immune to direct or indirect lightning
strikes; however, some proven installation practices
might greatly reduce the risk of undesirable affects.
2.2 Precautions during Installation
To minimize the risk of undesirable effects from
lightning strikes on high risk installations that use a
point-bus technology:
Do not run wiring outside the building.
If you must install the unit in a metal building,
keep the wiring at least 0.61 m (2 ft) away from
external metal surfaces.
Earth ground the unit correctly. Do not use an
electrical ground or telephone ground.
Avoid running wires near telephone, data, or
power lines inside a building. Historical evidence
shows that locating control panel wiring at least
0.61 m (2 ft) away from telephone, data, or power
lines is successful at minimizing lightning
damage. When your data lines must cross the
path of AC or other wiring, cross the lines
perpendicularly.

D9412GV3/D7412GV3 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 9
3.0 Overview
3.1 Configuration and Parts
Figure 1: System Configuration
Control
Panel
On-Board Points
1 to 8
D9131A Module connects
to a parallel printer to print
the event log.
D9 8 Module allows the control
panel to monitor two phone lines.
Each D81 8D OctoPOPIT combines
eight POPIT points in one module.
D813 Modules (two 1 VDC batteries)
provide additional power for keypads and
other powered devices.
D81 9 OctoRelay provides alarm
and auxiliary relay output.
(Other functions available.)
D9 10B Modules can be
used for access control.
Use keypads or keyswitches to arm the control panel by
area. The D941 GV3 control panel supports up to 3 areas.
The D741 GV3 control panel supports up to 8 areas. Each
area can have its own account number or areas can be
grouped together with a common account number. Points of
protection are assigned to areas.
D81 5, ISW-D81 5CW-V or D81 5MUX
Interface used for point expansion.
DX40 0 or ITS-DX40 0-G allows
communciation over a Local or Wide
Area Network (LAN/WAN).
Table 2: GV3 Series Control Panel Differences
Features D9412GV3 D7412GV3 D7212GV3
Access Control Yes - 8 doors Yes - 2 doors No
Arm/Disarm Passcodes 249 99 99
Cards/Tokens 996 396 N/A
Passcode-Protected Custom Functions 16 4 4
Number of Printers 3 1 1
Number of Points 246 75 40
Number of Relays 128 64 24
Number of Areas 32 8 4
Number of D1255 Keypads 16 16 8
Number of D1260 Keypads 8 8 8

D9412GV3/D7412GV3 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 10
3.1.1 Parts List
The D9412GV3 andD7412GV3 Control Panels are
shipped assembled from the factory with the following
parts:
Literature Pack
D9412GV3/D7412GV3 Program Record Sheet
(P/N: F01U170809)
7000/9000 Series Point Chart Label
(P/N: 79-06660-000)
Assembly
PC board
Faceplate shield
Mounting skirt
One #6 x 1/4-in. screw
3.1.2 Parts Available by Separate Order
Order the following components separately to
complete a basic eight-point installation.
The D1260 and D1260B Keypads must
have firmware version 1.04 or higher for
use with the D9412GV3 and D7412GV3.
D1255B, D1255, D1256, D1260, D1260B
Keypad, or D720 Keypad
D1255RB Fire Keypad, D1256RB Fire Keypad, or
D1257RB Fire Alarm Annunciator
D1640 Transformer
D126 or D1218 Battery
D161 or D162 Phone Cord (order two cords if
using the D928 Dual Phone Switcher)
D8103, D8108A, or D8109 Enclosure
Configured packages are also available. Please
consult the Bosch Security Systems, Inc. Product
Catalog.
The following literature is available in a separate
literature package for dealers.
D9412GV3/D7412GV3 Operation and Installation
Guide (P/N: F01U143070)
D9412GV3/D7412GV3 Approved Applications
Compliance Guide (P/N: F01U143069)
D9412GV3/D7412GV3 Program Entry Guide
(P/N: F01U170807)
 D9412GV3/D7412GV3 Program Record Sheet
(P/N: F01U170809)

D9412GV3/D7412GV3 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 11
3.2 Accessories
Refer to the Bosch Security Systems, Inc. product catalog for additional information.
Table 3: Compatible Accessories1
Model Title UL 864 Fire Intrusion
D122/D122L Dual Battery Harness X X X
D125B Powered Loop Interface Module X X X
D127 Reversing Relay X X X
D129 Dual Class A Initiation Circuit Module X X X
D130 Relay Module X X X
D185 Reverse Polarity Module X X
D192G Bell Circuit Supervision Module X X X
D279A Independent Zone Control (On-Board and OctoPOPIT Points) X
D720R LED Keypad (red) X X
D720W LED Keypad (white) X X
D928 Dual Phone Line Switcher X X X
D1255RB Fire Keypad X X X
D1256RB Fire Keypad X X X
D1257RB Fire Alarm Annunciator X X X
D1218 12 V, 17.2 Ah Rechargeable Battery X X X
D1255/D1255B Keypads (General Purpose) X X
D1255R Text Keypad (red) X X
D1255W Text Keypad (white) X X
D1256 Fire Keypad X
D1257 Fire Alarm Annunciator X
D1260/D1260B2Keypads X X
D1640 16.5 VAC 40 VA Transformer X X X
D8004 Transformer Enclosure X X X
D8125 POPEX Module X X X
D8125MUX Multiplex Bus Interface X X X
ISW-D8125CW-V2 Commercial Wireless Interface Module
D8128D OctoPOPIT Module X X X
D8129 OctoRelay Module X X X
D8130 Release Module X X X
D8132 Battery Charger Module X X
D9127U/T POPIT Module X X X
D9131A Parallel Printer Interface Module X X
D9210B Access Control Interface Module X X X
DX4020 Network Interface Module X X X
ITS-DX4020-G GPRS/GSM Communicator X X X
ICP-SDI-9114 SDI Splitter X X X
ZX776Z PIR Motion Sensor [15 m (50 ft)] with POPIT X
ZX794Z PIR Motion Sensor [24 m (80 ft)] with POPIT X
ZX865 PIR/Microwave Motion Sensor [+1.7C (+35F)] with POPIT X
ZX938Z PIR Motion Sensor [18 m (60 ft)] with POPIT X
ZX970 PIR/Microwave Motion Sensor [+1.7C (+35F)] with POPIT
1Where the fire alarm transmitter is sharing on-premise communications equipment, the shared equipment must be UL Listed (ITE
or fire protective signaling).
2 Version 1.04 or above

D9412GV3/D7412GV3 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 12
3.3 Features in the D9412GV3 and
D7412GV3
3.3.1 SDI Molex Connector
Use the SDI Molex Connector to easily connect an
SDI device to the SDI bus without needing to
disconnect wires connected to the SDI terminals.
Possible applications include:
Connecting a DX4010i to program the control
panel with Remote Programming Software (RPS)
at the premises
Connecting a keypad to test the control panel.
Do not connect the D5200 Programmer to
the SDI Molex connector.
Control panel firmware v8.11 or later
does not support the D5200.
UL requires that the DX4010i be used for
programming only.
3.3.2 Tip and Ring Posts
The tip and ring posts allow connecting a phone or
buttset for the purpose of troubleshooting
communications between the control panel and the
central station. This connection allows monitoring of
the dial tone, handshaking tones from the receiver,
and communications signals.
3.3.3 Telephone Line Sniff
The D9412GV3 and D7412GV3 control panels
monitor the phone line for the programmed
supervision interval before indicating a phone line
trouble.).
3.3.4 Points
The Bosch Security Systems, Inc. D9412GV3 Control
Panel provides up to 246 points of protection. The
D7412GV3 Control Panel provides up to 75 points of
protection. Point programming parameters determine
the control panel’s response to open and shorted
conditions on the sensor loop for the point. Several
options allow individual point programming to custom-
fit the protection to the installation.
Points 1 to 8 are located on the circuit board (on-
board points). They are standard sensor loops. The
remaining off-board points are POPIT points using
D8128D OctoPOPITs, D8125 POPEX Modules and
D9127 POPITs, or the ISW-D8125CW-V2
Commercial Wireless Interface Module.. MUX devices
can also be used with the D8125MUX.
Any points programmed as fire
supervisory points are latching.
3.3.5 Areas and Accounts
The D9412GV3 supports up to 32 areas. The
D7412GV3 supports up to 8 areas. You can assign all
points to a single area or distribute them over all
supported areas.
The control panel is armed and disarmed by area,
and several areas can be armed and disarmed with
one menu function. A passcode can also be assigned
an authority level that allows a user to arm an area
from a remote keypad in another area.Assigning each
area its own account number creates up to 32
separate accounts in the D9412GV3, and up to 8
separate accounts in the D7412GV3. Assigning the
same account number to different areas groups them
together in a single account.
Area options include exit tone and delay, separate fire
and burglary outputs, and multiple opening and
closing windows. Area type can be used to create
area interdependencies for arming purposes.
3.3.6 Digital Communicator
The control panel uses a built-in digital communicator
to send reports to the receiver. The control panel
sends reports in either the Modem IIIa2or ANSI-SIA
Contact ID format. All software versions for the D6600
can be used with the control panel.
The control panel connects to an RJ31X or RJ38X
jack for telephone line seizure. Connecting to the
RJ31X complies with FCC regulations for using the
public telephone network. The control panel can be
programmed to direct reports to four separate
telephone numbers. Adding the D928 Dual Phone
Line Switcher Module allows connecting and
supervising a second telephone line.
The system can route groups of Event Reports to four
different destinations. Each report group can be
programmed to send reports to one or more
destinations. Primary and backup reporting paths can
be programmed for each destination and each report
group. A custom option allows specification of
individual Event Reports to be sent.

D9412GV3/D7412GV3 |Operation and Installation Guide | 3.0 Overview
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 13
3.3.7 Keypads
Up to 32 unsupervised keypads can be connected to
the system. The available power, number of
supervised keypads, and number of areas covered
affect the total number of keypads that can be
connected.
The system can supervise up to sixteen D1255
keypads (all models), and up to eight D1260 keypads
(all models). The control panel sends a Serial Device
Trouble Report, SDI FAILURE in the Modem IIIa2
format or Expansion Module Failure (333) in Contact
ID format, if it loses communication with a supervised
keypad.
More than 16 keypads can be added, but the system
can only supervise up to 16 keypads. Table 4 on page
13 shows the keypads that are compatible with the
D9412GV3 and D7412GV3 Control Panels. Refer to
Keypad in the D9412GV3/D7412GV3 Program Entry
Guide (P/N: F01U170807) for complete details on
programming keypad options.
UL requires all Fire System keypads to be
supervised.
Table 4: Compatible Keypads
Model Display Application
D1255/
D1255B/D
1255RB
16-character
alphanumeric
Fire/Burglary/Access
D1256/
D1256RB
16-character
alphanumeric
Fire
D1257/
D1257RB
16-character
alphanumeric
Fire
D1260/
D1260B
4-line by 20-
character
Fire/Burglary
D720/
D720B
8 LED Fire/Burglary
3.3.8 Keyswitch
Maintained or momentary closure devices such as
keyswitches allow any of the available areas to be
armed or disarmed. Point programming determines
the loop responses and which area a keyswitch
controls.
3.3.9 Access Control
The D9412GV3 can control eight access doors (each
requiring the optional D9210B Wiegand Control
Interface Module) with up to 996 uniquely identified
cards or tokens. The D7412GV3 can control two
access doors with up to 396 uniquely identified cards
or tokens. Any of the following can grant access:
Wiegand-style access control device (card
reader) connected to the D9210B Access Control
Interface Module
Request to enter (RTE) or request to exit (REX)
input
Unlock command on a keypad
The access control features of the D9412GV3 and
D7412GV3 can deny access during armed periods.
The control panel can also grant access only to
certain authorized users depending on whether the
area is master armed, perimeter armed, or disarmed.
Programming for automatic disarming when
designated authorized users are granted access is
also possible.
3.3.10 Event Memory
The control panel retains point alarm and trouble
events in memory for each area. A D1255 (any
model) or a D1260 (any model) can be used to view
event memory by using COMMAND 40. The control
panel clears the previous events for an area from the
event memory when the area is armed.
3.3.11 Event Log
The system stores 800 events from all areas in its
event log. For example, the system adds at least two
items to the log each time an area is armed or
disarmed, the open (or close) event that also contains
the previous arming state.
All events can be stored even if the control panel
does not send a report for them. The log can be
viewed at a keypad, printed locally using the D9131A
Parallel Printer Interface Module and a parallel printer,
or uploaded using Remote Programming Software
(RPS).
For a list of the log events, refer to the appendix in the
user’s guide for the keypad.
3.3.12 Ground Fault Detection
The Earth Ground Terminal on the control panels is
electrically isolated from all other terminals to allow
the D9412GV3 and the D7412GV3 to detect ground
fault conditions. A Ground Fault Detect Enable switch
(S4) is located just under Terminal 10, Earth Ground,
on the control panel. Refer to Section 4.5.2 Ground
Fault Detect Enable on page 15 for information on
operating this function.

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 14
3.3.13 Ground Fault Detection Added Feature
When Ground Fault Detect is enabled (S4 closed),
Points 1 to 8 can be used for non-powered fire-
initiating devices such as heat detectors, four-wire
smoke detectors, and pull stations. A D125B Powered
Loop Interface or a D129 Dual Class A Interface
Module is not required when connecting the non-
powered fire-initiating devices to Points 1 to 8.
3.3.14 Conettix Functions
The D6600 Conettix System supports data network
communications. Conettix allows the D6600 Receiver
to connect to various network technologies including
Ethernet and GPRS (General Packet Radio System).
Connecting to a data network is possible using the
COM4 or COM1 connection from the D6600 Receiver
to the D6680 Network Adapter. Control panels can
send reports through telephone lines, Ethernet,
Token-Ring or GPRS networks to the D6600 receiver
at the central station. Once events are received, they
can then be issued to automation software or a
network printer through a local area network (LAN) or
wide area network (WAN).
Sending events to the central station over a LAN or
WAN requires a network interface module (NIM), such
as the DX4020. Sending events over GPRS requires
a special NIM, the ITS-DX4020-G.
3.3.15 Programming
Use the Remote Programming Software (RPS), or the
local Programmers Menu, to program the D9412GV3
and D7412GV3 Control Panels. Refer to the
D9412GV3/D7412GV3 Program Entry Guide (P/N:
F01U170807) for programming options.
3.3.16 Other Features
D9412GV3 and D7412GV3 Control Panels have
many programmable features. Some of the features
are listed below. Complete details on all features are
in the D9412GV3/D7412GV3 Program Entry Guide
(P/N: F01U170807).
Supervision of AC (primary power), battery
(secondary power), Zonex and SDI buses, central
processing unit (CPU), up to three printers, and
two telephone lines
Automatic System Test Reports
Remote access for programming, diagnostics,
and log uploads using the remote programming
software (RPS)
Fire alarm verification
Programmable alarm output
Programmable relay output using the D8129
OctoRelay Module
Opening and closing windows
Skeds (scheduled events)
Limited local programming available in the
Service Menu
4.0 Installation
4.1 Installation Preparation
This section contains a general installation procedure
and refers to other sections of the document for
detailed instructions.
Review this document and the D9412GV3/D7412GV3
Program Entry Guide (P/N: F01U170807) before
beginning the installation to determine the hardware
and wiring requirements for the features used.
Have the following documentation available when
reading through this guide:
D9412GV3/D7412GV3 Program Record Sheet
(P/N: F01U170809)
Security System Owner’s Manual
(P/N: 71-06633-000) and GV3 Series Owner’s
Manual Supplement (P/N: F01U143082)
Installation manual for keypad or annunciator
(D1255 all models, D1255RB, D1256, D1256RB,
D1257, D1257RB, D1260 all models, or D720 all
models)
Before installation, become familiar with the operation
of RPS or the local Programmers menu.
4.2 Enclosure Options
Mount the control panel assembly in any of the Bosch
Security Systems, Inc. enclosures listed:
D8103 Universal Enclosure (tan)
D8109 Fire Enclosure (red)
D8108A Attack Resistant Enclosure (tan)
Refer to the D9412GV3/D7412GV3 Approved
Applications Compliance Guide (P/N: F01U143069) to
determine if the application requires a specific
enclosure.
4.3 Mounting Enclosure
1. Run the necessary wiring throughout the
premises.
2. Mount the enclosure in the desired location. Use
all five enclosure mounting holes. Refer to
Figure 2.
3. Pull the wires into the enclosure.
Electromagnetic interference (EMI) can
cause problems on long wire runs.

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 15
Figure 2: Enclosure Mounting
8
2
1324
3
7
5
9
6
1 - Point chart label
2 - Mounting skirt hooks (2)
3 - Module mounting holes (12)
4 - Tamper switch mounting holes (5)
5 - Skirt mounting hole (1)
6- Enclosure mounting holes (5)
7 - Mounting skirt hook holes (2)
8 - Back of D9412GV3/D7412GV3 Control Panel
9 - Lock down tab
4.4 Installing the Control Panel
1. Place the control panel over the inside back of the
enclosure, aligning the large rectangular openings
of the mounting skirt with the mounting hooks of
the enclosure. Slide the control panel down so
that it hangs on the hooks. Refer to Figure 2, Item
2on page 15.
2. Remove the tape from the #6 x 1/4-in. screw in
the mounting tab on the control panel. The screw
passes through the mounting tab and into the
skirt mounting hole in the enclosure. Tighten the
screw to secure the control panel in the
enclosure.
3. Connect earth ground to the control panel before
making any other connections. Refer to Section
4.5 Connecting Earth Ground.
4.5 Connecting Earth Ground
4.5.1 Terminal 10
To help prevent damage from electrostatic charges or
other transient electrical surges, connect the system
to earth ground at Terminal 10 before making other
connections. Recommended earth ground references
are a grounding rod or a cold water pipe.
Caution: Do not use telephone or
electrical ground for the earth ground
connection. Use
1.8 mm (14 AWG) to 1.5 mm (16 AWG)
wire when making the connection.
Do not connect other control panel
terminals to earth ground.
4.5.2 Ground Fault Detect Enable
To meet UL 864 requirements, enable
Ground Fault Detect.
A ground fault is a circuit impedance to earth ground.
The control panel has a ground fault detection circuit
that, when enabled, detects ground faults on
Terminals 1 to 9 and 11 to 32. The control panel also
detects and annunciates ground faults on any device
connected to it.

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 16
If a ground fault condition occurs, the keypads display
SERVC GND FAULT and the control panel transmits
a GROUND FAULT TROUBLE, AREA 1.
When the control panel recognizes that the ground
fault condition is corrected, and remains corrected for
between 5 to 45 consecutive sec, a Restoral Report is
sent.
The D9412GV3 and D7412GV3 Control
Panels log and print a Ground Fault event
as a Trouble Point 256 if communicating
in Modem IIIa2format. If communicating
in Contact ID format, the control panels
generate a Ground Fault (310) event.
4.5.3 Enabling Ground Fault Detection
To enable Ground Fault Detect Enable, lock (close)
the S4 Ground Fault Detect Pin on the control panel
(Figure 3).
Figure 3: Enabling Ground Fault Detection
EAR THGROUND
COMMON
BA TTER Y NEG AT IVE ONLY
BAT TER Y POSITIVE ONLY
REL AY A
REL AY B
REL AY C
+AUXPOWER
CLAS S2 TRAN SFORM ER
16.5 VAC 40VA 60Hz
Model D 1640
Int e r nallyFused - Do not short
Requi res UnswitchedOutlet
Do not sharewithot he requi pment
S4 GROUND FAU LTDETECT
Enabl ed
Di sabled
RED
ON whencomm unicating
OFFwhen idl e
Co mmercialPr ot ect ed- Pr emis esControlPa nel
D9412G V3ControlPanel is ULListed For Cent r al Stat ion, Local , Aux iliar y, Propr i etary,and Househol d
Fi re Al arm,andCent r alStat ion, Local , PoliceSt ationCo nnect,Househol dBurgl ar Al ar m andEnc r ypt ed
Li neSec ur i ty whenc om m unicat ing via anet work.
Systemisintended tobe checkedby aQualifiedTechni cian at least every3 years.
Th etypesof initiat ing ci rcui ts the cont rol panel has been a pproved f or are A, M,W,SS.
Th etypesof si gnalingthe controlpanel has beenappr oved for are DAC, OT,NC
VOLTA GERANGES
O pen 3. 7 - 5. 0V DC Short 0.0-1. 3 VDC
N or m al 2. 0 - 3. 0VDC
ResetPin
Disab le al l except Bat t ery
Ch ar gingan dP rogramming
PERI PHER AL DEVI CE CONNECTIONS
RED P OWER +
YELLO W DATA BU SA
GREEN DATABU SB
BLAC K C OMMON
ZON EXOUT1
ZONEXIN1
N. F.P. A.
St yle 4.0
Si gnaling
Li ne
Ci rcu its
F01U143074- 02
LE Ds O ffWh enNormal
YE LLO W -C har gi ng St a tus
RED - Low Batter y - 12.1 VDC
10. 2VDC-Batter y Loa dShed
Thi sequi pment should beinstal led inaccordancewiththeNFPA70 (Nati onal Elect r ical Code) and
NF PA72 (Nati onal FireAlarmCode ) forLocal , Ce n t ral St ati on, Pr opr iet ary andH ousehold Fire Warning
Syst ems and unde r thelimitsof theLocal Author ity Having Jur isdi cti on(National Fi re Prot ection
Asso ciation, Ba t t e rmarch Park, Qui ncy,M A 02269).Pr int ed inf ormation describing pr ope r instal lat ion,
oper at ion, testing,mai nt enance, evacu ationpl anning and repai r serviceist obe provi dedwiththis
equi pmen t.
D9412GV3
26
25
ZO NEX POWER +
24
ZO NEX COMMON
23
PHONE LINE SEIZED LED
TIP
RING
TELCOCORD MODELD161
SDI Conn ect or
ZON EX OUT 2
ZONEXIN 2
Refer tothe D9 4 12GV3/D 7412G V3 Ap pr oved App lication sComplian ceGuide(P/N:F01U 143069)
forSy stem Wiring Diagram,Iss ueAan df or com pat ible sm oke det ect or s.
PO W ER SUPP LY REQUIREMENTS
ThePowerSu ppl y provide sa m axi mumof 1. 4 Amps forthe ControlPanelan dal l
A ccesso ryDevice s. For SystemL oadi ng, referto theD 9412G V3/ D74 12GV3O per at ion
an dInstallat i on Gui de (P/N:F0 1U1430 70).
( P/ N: F01U1 43070) for PowerRe qui rem en ts r elatingto Terminals 6 an d 7 .
CA UTION:
Re f er to theD 9412G V3/ D741 2GV3Operationan dInstallati on Gui de
All externalconn ect ion sexc e ptTe r m i nal 5 (battery positive) arei nher ent l ypower
limited.Re quirem en ts f orba tterystan dby timemi ghtred uce allowableou tput.
WARNING!
Multi-Ba tte ryin stallat i on re qu ires
Mo de lD 122/ D 122 L Du al Ba ttery
H ar n ess . Impro per installationcan
beafire h azard .
B at ter y: R eplac e ever y 3to
5yearswithoneortwo Mod el
D126or D121812 V Le ad Acid
B at t er i es.
Inco rrect wiring will
dam age this equi pm ent .
PR OGRAMMABLE
ALARMOUTPUTS
Ter m inal s
SW I TCH ED AUX
and67
Ter minal 8
Oper at ion Moni torLED
Pulseswhen Nor m al
Flickerswhen Ri ng ing
GREEN
D5200/D5360
PRO GCONN
Po int 8, S3 Option
Cl ose d = 1k EO L
Nor mal Operat ion
Open =AB- 12 UL
Bel l Bo x 220 k
25
Poi nt 3Point 4
161514
Point1 Poi nt 2
1211 13
Poi nt 5Point 6
1817 19
Point 7 Poi nt 8
21
20 22
Suitabl e fordr y ind oor
useonly.
Devi ces pow er ed bythe
AUX power out put must
besupervised.
Mini mum system req uirementsforCl assificat ion inaccordancewithAN SI/SIACP -01-2000:
UL List ed andCl assified cont rol uni t ModelD9412GV3, D7412G V3, orD7212G V3;
UL List ed andCl assified keypadModelD1256, D1257, D1260, D1255,D 1255R, orD1255RW;
UL List ed Local Bell
WARNING !
To pr eve n t risk of
el ect ri c shock,
di sconn ect AC po wer
and t el ephon elines
before servicing .
CA UTI ON:Avoi dda m ageto Panel.
Do not connect24Vtoterminals.
Max imumch argingcu rrent 1.4 A
Re setPi n
Disab le Al l Exc ept Battery
ChargingA nd Pr og ramming
27
PR OG
CONN
26
25
24
Re set Pi n
Disab le Al l Exc ept Battery
Ch ar g ingA nd Pr og ram m i ng
27
PRO G
CO NN
26
25
24
2
1
1 - S4 Locked (Closed). Control panel detects
ground faults.
2 - S4 Unlocked (Open). Control panel does not
detect ground faults.
4.5.4 Ground Fault Specifications
Table 5 provides the impedance specifications for
detecting ground faults when any terminal or field
wiring is shorted to ground.
Table 5: Ground Fault Impedance
Specifications
Impedance Control Panel Detects Ground Fault
≤300 ΩYes
300 Ωto
200 kΩDetection depends upon the terminal
≥200 kΩNo
4.5.5 Locking the Reset Pin
Locking the reset pin disables the control panel
(Figure 4). When the control panel is disabled, the
system ignores most keypad commands and points.
CALL FOR SERVICE appears in keypad displays
when the pin is locked down.
On-board relays (Terminals 6 and 7) and off-board
relays deactivate when the control panel is reset.
Terminal 8 has power when the relay is deactivated.
Activation interrupts power at that terminal. The on-
board relay (Terminal 8) remains deactivated when
the reset pin is locked in the disable position.
Releasing the reset pin from the closed position
resets the control panel. The control panel resets all
its timers, counters, indexes, and buffers. Any points
that restore after a reset do not generate Restoral
Reports.
If the reset pin is placed in the disable position when
all areas are armed, there must be an entry in the
Answer Armed program item. Refer to RPS
Parameters in the D9412GV3/D7412GV3 Program
Entry Guide (P/N: F01U170807).
Locking the pin in the disable position applies power
to the control panel and charges the battery while the
detection devices and keypads are installed.
Figure 4: Reset Pin
1 - Reset pin locked (closed)
2 - Reset pin normal (open)

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 17
4.6 Completing the Installation
If not already complete, make the earth ground
connection to Terminal 10 and lock the reset pin in
the closed position.
4.6.1 Charging the Battery
Connect the battery, then the transformer to allow the
control panel to charge the battery while you complete
the installation. Refer to Section 5.0 Power Supply on
page 22 for instructions.
On-board Buzzer Sounds at Power Up and Reset:
The system performs a series of self-diagnostic tests
of hardware, software, and programming at power up
and at reset. The buzzer on the control panel sounds
during the tests. The self-diagnostics tests complete
in approximately 1 to 3 sec.
If the control panel fails any test, the buzzer continues
sounding and a System Trouble message appears at
the keypads.
Touch Terminal 10 First: If the on-board buzzer
sounds briefly when the control panel is touched, any
static charge you carry discharges to the control
panel.
Avoid electrostatic discharge. Always
touch Terminal 10, the earth ground
connection, before beginning work on the
control panel.
If the control panel receives an electrostatic
discharge, it might generate Watchdog Reset and
Param Fail events.
4.6.2 Installing and Wiring Detection Devices
Install and wire detection devices and keypads at their
locations throughout the premises. Do not connect
the control panel yet.
Section 8.0 On-Board Points on page 31 contains
instructions for wiring the on-board points to detection
devices. Section 11.0 Arming Devices on page 55
contains instructions for wiring the keypads.
Instructions for wiring the off-board point POPIT
sensor loops are found in the instructions packaged
with the POPIT modules.
4.6.3 Installing Modules and Relays
1. Power down the unit by unplugging the
transformer and disconnecting the battery.
Always power down the unit when
installing modules or relays, or when
making wiring connections to the control
panel.
2. Install and wire any modules required for the
installation as described in the module’s
installation instructions.
Instructions for the D8125 POPEX Module,
D8128D OctoPOPIT Module, D8129 OctoRelay
Module, D811 Arm Status Relay Module, and
D928 Dual Phone Line Switcher appear in this
guide.
Refer to Section 9.0 Off-Board Points on page
36 for D8125 and D8128D instructions. Refer to
Section 10.0 Off-Board Relays on page 50 for
D8129 and D811 instructions. Refer to Section
7.11 D928 Dual Phone Line Switcher on page 30
for D928 instructions.
3. If using the power outputs at Terminals 7 or 8,
refer to Section 6.4 Programmable Power Output
Terminals 6, 7, and 8 on page 27 for
instructions.
4.6.4 Connecting the On-board Points and
Keypads
4. Connect the on-board points and keypad wiring to
the system. Refer to Section 8.0 On-Board Points
on page 31 and Section 11.0 Arming Devices on
page 55 for instructions.
4.6.5 Powering Up
Reconnect the battery, then plug in the transformer.
The buzzer sounds for two sec when the control panel
is powered up. Leave the reset pin in the locked
position.
Yellow Charging Status LED Remains Lit: If the
yellow charging status LED remains lit after five
minutes of powering up the control panel, either the
battery is deeply discharged or too many powered
devices were connected to the control panel.
Combined continuous current draw for Terminals 3, 8,
24, and 32, and the accessory connector cannot
exceed 1.4 A. Refer to Section 6.0 Power Outputs on
page 26 for help.
4.7 Programming the Control Panel
If the control panel is not already programmed, review
the D9412GV3/D7412GV3 Program Entry Guide
(P/N: F01U170807). Ensure that all accessory
modules for desired features are available for
installation.
Use RPS to load a custom program into the control
panel as needed.

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 18
4.8 Installing the Point Chart Label
The point chart label is required for fire
systems with verifications points.
A point chart label is included in the literature pack.
Install the point chart label for fire or combined fire-
and-burglary systems that use verification points.
Use the D9412GV3/D7412GV3 Program Record
Sheet (P/N: F01U170809) to gather the necessary
information for completing the point chart. Fill out the
label and install it on the inside of the enclosure door
(refer to Figure 2 on page 15).
Avoid smearing the entries on the chart.
Use the peel-off backing to press the
label in place.
4.9 Testing the System
After installing and programming the control panel,
test the system completely. Test the control panel and
all devices for proper operation.
Test after initially programming the control
panel.
To meet UL 864 requirements, perform a
full system test after any subsequent
programming session.
Refer to Section 4.10 Service Walk Test on page 18
for complete Service Walk Test instructions.
Clear after Test: To clear the event memory and
report buffer, momentarily close the reset pin. Events
stored in the control panel’s event log are not cleared.
4.10 Service Walk Test
The Service Walk Test differs from the standard Walk
Test. In the standard Walk Test, POPITs whose
switches are set for a point number not programmed
in the control panel do not appear in the test. In the
Service Walk Test, POPITs whose switches are set
for a point number that is not programmed in the
control panel do appear in the test.
The Service Walk Test allows a user to walk test all
246 points from a control-panel-wide keypad,
regardless of the point index type.
A Service Walk Test can also be initiated by account-
wide or area-wide keypads but test only those points
that are within the scope of the keypad that initiated
the function. The Service Walk Test does not test
points in armed areas.
Only Walk Test Start and Walk Test End
are reported to the central station.
The D9131A can be configured for local
printing. Refer to the D9412GV3/
D7412GV3 Program Entry Guide
(P/N: F01U170807).
During a Service Walk Test, the summary
alarm and summary fire remain off,
because there are no Fire or Burg alarm
conditions to summarize. The P# Relay
Response Type feature operates as
programmed.
Service Walk Test Procedure.
Refer to Figure 5 on page 20 and Figure 6 on page 21
for Service Walk Test options. Refer to the Walk Test
procedures in the GV3 Series Owner’s Manual
Supplement (P/N: F01U143082) when using a D1260
or D1260B Keypad.
1. Choose a keypad to conduct the test. Ensure that
the display shows the idle disarmed text.
2. Press the [MENU] key to enter the Function List.
Press [NEXT] repeatedly until the SERVICE
WALK ? prompt appears.
3. Press [ENT], or press [9][9] followed by [ENT] to
reach the Service Menu to access the Service
Walk Test.
The D7412GV3 does not include the
Service Walk Test in the Service Menu.
Enabling the Service Walk Test function
in the Function List provides access to
the Service Walk Test in the D9412GV3.
4. The display shows ### PTS TO TEST .Test the
first detection device.
5. When a detection device is faulted, the keypad
emits a brief tone and displays the point text of
the point tested for 60 sec. After 60 sec, the
display returns to the ### PTS TO TEST
message.
Extra Points display default text: If the switches on
a POPIT are set incorrectly to a point number that is
not in the program for the control panel, the default
text for that point number (PT ###) appears when the
point is faulted. Refer to the control panel’s program
record sheet for the default text for all points.
Faulting the point a second time produces the tone
and shows the point text, but does not decrease the
count in the ## PTS TO TEST message.

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 19
5. To see the points that remain untested during the
Service Walk Test:
a. Press [ESC] when point text appears. The
display shows ## PTS TO TEST.
b. Press the [ESC] key. VIEW UNTESTED ?
appears.
c. Press [ENT]. ## PTS UNTESTED appears.
d. Press [NEXT] to see a list of the points that
have not yet been tested. Move through this
list by pressing the [NEXT] key.
e. To resume the Service Walk Test, press
[ESC]. ## PTS UNTESTED appears.
f. Press [ESC]. ## PTS TO TEST appears.
g. Resume testing points. To end the Service
Walk Test, press [ESC] twice.
6. After the last point is tested, 0 PTS TO TEST
appears. Press [ESC]. The display shows ALL
PTS TESTED briefly before returning to idle text.
The Service Walk Test, when performed
on a D7412GV3, cannot display “0 PTS
TO TEST” because the D7412GV3 is
physically unable to connect to the
second POPEX Module (used for Points
129-247).
Automatic time-out returns the system to
idle text: If there is no point or keypad
activity for 20 min., the Service Walk Test
ends automatically. The keypad returns to
idle text.

D9412GV3/D7412GV3 |Operation and Installation Guide | 4.0 Installation
.
Bosch Security Systems, Inc. | 10/10 | F01U143070-03 20
Figure 5: D9412GV3 Service Walk Test Flow Chart
[ENT]
[ENT]
[ESC]
[ESC]
[ESC]
[ESC]
[NEXT]
Test a device
Test a device
Test a device
Test a device
(Text displays for 60 seconds)
(Text displays for 60 seconds)
IDLE TEXT
SERVICE WALK?
246 PTS TO TEST
POINT TEXT
245 PTS TO TEST
POINT TEXT
244 PTS TO TEST
POINT TEXT
1 PTS TO TEST
VIEW UNTESTED?
0 PTS TO TEST
# PTS UNTESTED
POINT TEXT
[ESC]
[ESC]
[ESC]