Bosch Security Systems Blue Line A1-CC User manual

4 | BLA1-CC Color Camera Modules
Modifications reserved | 4998153860en-01
Bosch Security Systems For more information, visit:
www.boschsecuritysystems.com
130 Perinton Parkway
Fairport NY 14450
USA
The BLA1-CC-N camera module provides an NTSC video sig-
nal of 512 (H) x 492 (V) effective pixels with electronic shutter
speeds from 1/60 second to 1/100000 second.
The BLA1-CC-P camera module provides a PAL video signal of
512 (H) x 582 (V) effective pixels with electronic shutter speeds
from 1/50 second to 1/100000 second.
Der Standardsockel wird aufgesetzt und rationell mit Schnappverbindungen be
BLA1-CC-N Color Camera Module
(NTSC format)
Order Number BLA1-CC-N
BLA1-CC-P Color Camera Module
(PAL format)
Order Number BLA1-CC-P
1 |Intrusion BLA1-CC Color Camera Modules
Security you can rely on.
Family 1.1.1
123 456789
Blue Line A1-CC
Color Camera Modules
The BLA1-CC color camera modules
attach to the Blue Line detectors.
These camera modules, available in
either NTSC or PAL formats, are small,
easy-to-mount, and attractive. The
camera can be set to run continuously
or to run for either 15 seconds or 90
seconds when triggered by the
detector alarm.
Series Features
• Color charge-coupled device (CCD) camera with 3.4 lx
light sensitivity
• NTSC or PAL video format
• 330 lines of horizontal resolution
• The camera may be left on or controlled by the detector
alarm
• Selectable (Form A or Form B) alarm relay outputs
• Includes video cable with BNC (Bayonet Neill-Concel-
man) connector
Series Listings, Certifications, and Approvals
Country Certification/Listing Number
Canada IC (R SS-210)
Europe 
US ANSR: Intrusion Detection Devices
(UL639)
FCC (Part 15)

2 | BLA1-CC Color Camera Modules
Series Application Information
Camera View
The camera's viewable area is shown below:
Note: The camera's field of view varies depending on the
size of the detector on which it is mounted and the
height at which it is installed. The passive-infrared
(PIR) coverage patterns and look-down zone
shown are for reference only.
Top View
Field-of-view legend
PIR coverage pattern look-down zone
camera's field of view
Side View
Power Considerations
Power Limits
Input power must be provided by an Approved Limited Power
Source. All outputs must be connected to SELV (Safety Extra-
Low Voltage) circuits only.
Standby Power
This detector has no internal standby battery. For UL Listed
product installations, 4 hr (20 mAh with camera off, 400 mAh
with camera on) of standby power must be supplied by the con-
trol unit or by a UL Listed burglary power supply.
BLA1-CC Color Camera Modules | 3
Video Connection
A video cable with a BNC connector at one end is supplied.
Connect this cable to up to 500 ft (152 m) of 75 ΩRG59/U or
similar coaxial cable.
Series Technical Specifications
BLA1-CC Series Specifications
Enclosure Design
Color: white
Dimensions (HxWxD): 2.2 in. x 2.4 in. x 1.9 in.
(5.6 cm x 6.1 cm x 4.8 cm)
Material: High-impact ABS plastic
Environmental Considerations
Relative Humidity: 0 to 95%, noncondensing
Operating Temperature: +14°F to +120°F (-10°C to +49°C)
For UL Listed product installations,
+32°F to +120°F (0°C to +49°C)
Input
Alarm: 5 V normally from sensor digital alarm
output, ground for 4 seconds during
alarm.
Outputs
Relay Timer: Selectable latch time of 15 s or 90 s.
Timed Relay: Solid state, selectable supervised Form
A normally-closed (NC) or unsuper-
vised Form B normally-open (NO) con-
tacts rated for 125 mA at 28 VDC, 3 W.
Tamper: Normally-closed (NC) contacts (with
cover on) rated at 28 VDC, 125 mA
maximum. Connect to detector tamper
circuit.
Power Requirements
Current (Alarm): 100 mA when camera is on.
Current (Standby): 5 mA maximum at 12 VDC
Voltage (Operating): 10 VDC to 14 VDC
Radio Frequency
Interference (RFI)
Immunity:
No alarm or setup on critical frequen-
cies in the range from 26 MHz to
2000 MHz at 30 v/m.
Video
CCD: 1/3-inch (8.5 mm) color with an elec-
tronic shutter
Lens: 3.6 mm fixed focal length lens
Resolution (horizontal): 330 lines minimum at center of picture
Scanning System: 2:1 interlaced
Sensitivity: <3.4 lx
Signal: 75 Ω(NTSC or PAL)
Signal to Noise Ratio: 45 dB minimum