Bosch ICP-AMAX4-P2-EN User manual

AMAX panel 4000 / AMAX panel 4000 EN
ICP-AMAX4-P1 / ICP-AMAX4-P2-EN / ICP-AMAX4-P3-EN
en Quick Start Guide

Table of contents
1Short information 4
2System overview 5
3Installation 7
3.1 System Power Up 7
3.2 System Status Indicator 7
3.3 Installer and User Code Commands 7
3.4 Prerequisites for Certification conform Installation 9
4Configuration 10
4.1 Programming with Keypad 10
4.1.1 LCD Keypad Menu Programming 10
4.1.2 LED/Icon LCD Keypad Address Programming 10
4.2 Reset to Factory Default Settings 11
4.3 LCD Menu Programming 12
4.4 Address Programming 20
4.4.1 Communication and Report Setting 20
4.4.2 Zone Programming 26
4.4.3 Output Programming 38
4.4.4 Access Codes 43
4.4.5 System Programming 49
5Troubleshooting 63
6Technical Data 66
AMAX panel 4000 / AMAX panel 4000
EN Table of Contents | en 3
Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Short information
Thank you for choosing the AMAX panel 4000. This is a flexible, reliable, convenient, and easy-
to-use alarm system. It has 16 wired zones on board, expandable up to 64 wired and wireless
zones.
This Quick start guide is provided with the system to give basic information about the system
wiring, components, and describe how to simply program and operate the system with IUI-
AMAX4-TEXT keypad, IUI-AMAX3-LED16 keypad, IUI-AMAX3-LED8 keypad, ICPKP8-LED keypad,
or ICP-KP8L-Icon LCD keypad. As the system includes a large number of programmable
functions and options, we suggest reading the complete installation manual. For detailed
operation method, please refer to the User Guide.
1
4en | Short information AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

System overview
Information:
Customer:
Location:
Account #:
Installer:
Date:
2
AMAX panel 4000 / AMAX panel 4000
EN System overview | en 5
Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Wiring Diagram
Program Key Port
GND
-
+
A C
AC
Transformer
Battery
Tamper
L2 COM COM COM
L1a L3 L4 L5 L6 L7 L8
L9
COM
COM
COM
COM
L10
L11
L12
L13
L14
L15
L16
P0+4
R
B
G
Y
AUX1
-
AUX2
-
AUX1
+12V
Y
G
B
R
RINGRHTHTIP
L1b
P0+3
P0+
P0-2
P0-1
Zones
Bosch Option
Bus 2 < 900mA
+12V
+0 V
1
2
3
3
1 Tamper Switch
2 Zone Switch
3 EOL 2,2 k
3
2
3
2
Fuse 1 A
PO+4: < 750mA
PO+3: < 750mA
PO -2: < 500mA
PO -1: < 500mA
230V ~50Hz
230mA
Wachdog
output
<100mA
12V < 18Ah
18VAC@50VA
Zones
AUX 1: < 900mA
AUX 2: < 900mA
AUX Power
Fire
Intrusion
Risk of shock if N,L1 or is connected incorrectly.
For operation safety, the ground terminals must
be connected.
3
3
2
Slow flash: Normal state
On: Trouble state
Off: Trouble state
_
_
_
_
_
_
_
_
+12V
+12V
+12V
COM
_
12V 7Ah
AUX2
+12V
_
COM
supervised
PO-5
Z1
2
23
3
Keypads:
IUI-AMAX4-TEXT
IUI-AMAX3-LED16
IUI-AMAX3-LED8
Keypads:
IUI-AMAX-LED8
IUI-AMAX-LCD8
I/O Moduls:
DX2010 Adr. 103 - 108
DX3010 Adr. 150 - 151
DX4010 Adr. 253
Communicators:
DX4020G Adr. 134
B426 Adr. 134(6) / 250(9)
RF Receiver:
RF3227E 1=
RFRC-OPT 1= (1)
1 =
2=
3 =
4 =
1=
2=
Bosch Option
Bus 1 < 900mA
COM
R
BGY
R
B
G
Y
R
B
G
Y
♥
IUI-AMAX3 +4 Keypad
3
1
2
1
Factory
Default
5-16 Inst. Guide
I
2000mA
100 Ω - 2,2 k
_
<
∑
3
6en | System overview AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

Installation
This system / product must be installed by a qualified installer / service person.
During installation and wiring, the control panel power source must be switched-off to prevent
equipment damage.
– To switch off the Power Source, an easy accessible circuit breaker must be available.
– The System / product must be connected to a socket-outlet with a protective earthing
contact
The User has to disconnect all Telecommunication Network Connectors before unplugging the
power adaptor
After the control panel wiring is completed, connect the AC power and backup batteries.
The power light on the keypad will light to show that AC power is connected.
Notice!
- Use only non spillable battery
- Battery must be recycled and disposed of properly
- When battery is not replaced correctly risk of fire explosion or burning
Notice!
The system must be installed and maintained by qualified installer / service person.
Bosch recommends testing the whole alarm system at least once a week.
Maintenance should be done by qualified installer / service person four times a year.
System Power Up
After the system is powered up, set date and time. Otherwise, the system prompts as fault.
After the system is powered up or reset, it resets to previous arming / disarming status.
To reduce false alarms caused by system power-up (or by power supply restoration after both
mains supply and AUX power supply fail), the system is designed to not perform zone test
within one minute after power-up.
System Status Indicator
The system status is indicated by the LED status indicator on the system main board.
Slow flash of red status indicator (repeating on and off with an interval of 1 second) indicates
normal system operation.
Installer and User Code Commands
The system supports programmable 4- to 6-digit Installer and User Code to execute the
following programming and operating commands.
The installer commands can be used only when all areas of the system are in disarming status
with no alarm activated and when installer access is enabled from user.
Notice!
No identical User Codes are allowed. User Codes are not permitted to be the same as
Installer codes.
3
3.1
3.2
3.3
AMAX panel 4000 / AMAX panel 4000
EN Installation | en 7
Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

User Code Commands
Function
(Default User Code = 2580
Default Inst. Code = 1234)
Command
Duress User Arming User Basic User Super User Master User Instal. User
Switch to M ain Keyp ad [Code] + [0][0][0] + [#] (Text K P ) √ √
Switch to P a rtitio n 01-16 [Code] + [0][ _ ][ _ ] + [#] (Text KP ) √ √
AW AY arm [Code] + [1][1] + [#] / [C ode ] + [#] / [#] (Q uick arm ) √ √ √ √ √ √
STAY arm [Code] + [1][2] + [#] / [C ode ] + [*] / [*] (Quick arm ) √ √ √ √ √ √
Disa rm [Code] + [#] √ √ √ √ √
D ispla y Info (F ault/T am per..) [C ode] + [-] √ √
Keypad Emergency Alarm
Keypad Fire
Keypad Medical Alarm Long press [7] and [9]
Fault/Tam p er In quire [C ode] + [2][1 ] + [# ] √ √ √
Check All Event Log [Code] + [2][2] + [#] √ √ √
Check EN Event Log [Code] + [2][3] + [#] (Text K P) √ √ √
Check Dialer Event Log [Code] + [2][4] + [#] (Text K P) √ √ √
Zone Bypass/Cancel
[Code] + [3][1] + [#] + [Zone No] [*] + [#] (Bypass) √ √ √ √
[Code] + [3][1] + [#] + [Zone No] [*] + [#] (Cancel LED) √ √ √ √
[Code] + [3][2] + [#] + [Zone No] [*] + [#](Cancel Text KP) √ √ √ √
Bypass Inquire
[Code] + [3][3] + [#] (Text KP) √ √ √ √
B ypa ss F au lt/Tam pe r [C ode] + [3][4 ] + [# ] √ √ √ √
Siren test [Code] + [4][1] + [#] √ √ √
C om m u nica tion te st [C ode] + [4][2 ] + [# ] √ √ √
W alk test [Code] + [4][3] + [#] √ √ √
C ha nge/V ie w d ate /tim e [C ode] + [5][1 ] + [# ] √
Daylight Saving Tim e (+1h) [Code] + [5][2] + [#] √ √ √
Daylight Saving Tim e (-1h) [Code] + [5][3] + [#] √ √ √
Add / D elete / Change U ser [Code] + [5][4] + [#] √ √
Change Individua l C ode [Code] + [5][5] + [#] √ √ √ √ √ √
C ha nge D om estic P ho ne N o.1
[Code] + [5][6][#] + [ _ _ _ _ _ _ ][#] (LE D K P) √
C ha nge D om estic P ho ne N o.2
[Code] + [5][6][#][#] + [ _ _ _ _ _ _ ][#] (LE D K P) √
C ha nge D om estic P ho ne N o.3
[Code] + [5][6][#][#][#] + [ _ _ _ _ _ _ ][#] (LE D K P) √
C ha nge D om estic P ho ne N o.4
[Code] + [5][6][#][#][#][#] + [ _ _ _ _ _ _ ][#] (LE D K P) √
Change D om estic P h one No.1-4 [Code] + [5][6][#] + [_] + [#] + [ _ _ _ _ _ _ ][#] (Text KP ) √
Call Back [Code] + [5][7] + [# ] √
Change La nguage
[Code] + [5][8] + [#] + [ _ ] [_ ] + [#]
01= E N 02=D E 03=ES 04 =F R
05= IT 06 = P L 0 7=N L 08 =S E
√ √ √
R eset ta m per or fa ult [C ode] + [6] + [#] √ √ √
Installer Access
[Code] + [7][1] + [#] (Enable)
[Code] + [7][2] + [#] (Disable) √
System reset [Code] + [9][9][8][9] + [#] √ √ √
Ins ta ller p rog ra m m ode [C od e] + [9][5][8] + [# ] √
Exits P rog r. m ode without save [9][5][9] + [#] (only in Adress P rog r. M ode) √
E xits P rog r. m o de with sa ve [9][6 ][0] + [#] (only in A dress P rogr. M ode) √
Set Factory D efau lts [9][6][1] + [#] (only in A dress P rogr. M ode) √
Copy control panel data to progr. K e y [9][6][2] + [#] (only in A dress P rogr. M ode) √
Copy progr. key data to control panel. [9][6][3] + [#] (only in Adress P rog r. M ode) √
Disp lay F W version [9][9][9] + [#] (only in Adress P rog r. M ode) √
Long press [1] and [3] or [*] and [#]
Long press [4] and [6]
Figure 3.1: User Code Commands
8en | Installation AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH

Prerequisites for Certification conform Installation
EN 50131-3 Grade 2, Environmental Class 2
– System must be placed inside the monitored area on a stable surface.
– Keypads must be mounted to the inner side of the monitored area.
– Once the system is tested and ready to use, Enclosure Door and Accessory Enclosures
must be secured with the provided screws
– To realize EN conform Alarm Indication and Transmission, one of the following options
must be used
– Two supervised Warning devices (PO-1 PO-2 & PO+) and one ATS 2 Communicator
(onboard Dialer, B426, D4020 or DX4020G)
– One self powered Warning Device and one ATS 2 Communicator (onboard Dialer,
B426, D4020 or DX4020G)
– Two Communicators, one ATS 2 (onboard Dialer, B426, D4020 or DX4020G) and one
ATS 1 (onboard Dialer, B426, D4020 or DX4020G)
– One ATS 3 Communicator (DX4020 or B426)
All Communicators must be connected to a Central Monitoring Station.
Only the onboard Dialer and the Option Bus Communicators can be used for EN Alarm
Transmission.
– one 12V/7AH or one 12V/18Ah Battery must be connected to the System.
– max current for all components with a 7Ah Battery = 550mA
max current for all components with a 18Ah Battery = 1500mA
(standby 12h, recharge Battery 80% in 72h)
(PCB=l00mA, IUI-AMAX Keypads=31mA, DX2010=35mA, DX3010=10mA, B426=100mA,
DX4020G=65mA, RF3227E=30mA, RFRC-OPT=30mA)
– To realize EN conform Arming procedure an indication of arm/disarm status must be
accessible from outside the monitored area (this indication can be time limited)
– To realize EN conform Access to the Monitored Area, one of the following options must
be used
– Opening a door (to the entry/exit route) must start the entry procedure
– Indication of arm/disarm Status
– Access to the monitored Area (doors not starting entry procedure) is prevented (e.g.
door strike, mechanically)
The Enclosure lock can only be used in non EN setup.
– Telephone arming can only be used in non EN setup.
– Accessory Modules, except input module (DX2010) can be used only inside the enclosure
(on the adapter plate).
– When input module (DX2010) is used in the external enclosure (AE20) the tamper skirt
must be installed on the PCB of input module (DX2010)
– The panel must be programmed with the EN settings indicated on the programming
sheet. When the panel is set without EN parameters, the EN Indication (on Label) must
be removed.
3.4
AMAX panel 4000 / AMAX panel 4000
EN Installation | en 9
Bosch Sicherheitssysteme GmbH Quick Start Guide 2013.07 | 03 | F.01U.267.113

Configuration
The control panel programming options are stored in a non-volatile flash memory. This
memory has all relevant configuration and user-specific data even after a total power loss.
Because the data retention time is quite long without power, reprogramming is not required
after powering up the control panel.
Programming with keypad is possible only when all of zones in the system are in disarmed
status and no alarm is activated. Installer Code is required for programming.
Notice!
It is not recommended to use other keypads or methods simultaneously to program the
system while programming with the current keypad.
Programming with Keypad
LCD Keypad Menu Programming
1. Enable Text keypad and confirm that the system is in disarmed status.
2. Enter Installer Code + [958] and press [#] to get to [Installer Menu].
3. Programming: Select the menu and operate according to the menu prompt.
– Down to the next menu: Press [▼]
– Up to the previous menu: Press [▲]
– Enter menu or confirm input: Press [#]
– Back to the menu or delete a single input: Press [-]; or press and hold [-] for 3
seconds to end the input state and get back to the menu.
– Operate according to the menu prompt. Select menu and enter data for specific
programming items according to the display on the keypad to complete
programming, step by step.
– The data value ranges in the menu programming and address programming are the
same. For specific options and value ranges, see contents in LCD Keypad Menu
Programming, page 10.
4. After completing input, press [-] to get back to the previous menu. Complete all
programming input by repeating step 3 and press [-] to get back to the current main
menu level by level.
5. Press [-] to enter menu options. It is optional to save or not to save the programming
information.
6. Select [Save and Exit] and press [#] to save system programming data, exit menu
programming and reset system.
LED/Icon LCD Keypad Address Programming
1. Enable LED keypad or Icon LCD keypad and make sure that the system is in disarmed
status.
2. Enter programming mode: Enter the Installer Code (the default is 1234) + [958] and
press [#].
3. Programming: Move to the required address and enter the value for each data bit (data
value).
– After entering programming mode, the system directly enters the programming data
in the address 0000 (Receiver 1 telephone number or the initial digit of the IP
address), then
4
4.1
4.1.1
4.1.2
10 en | Configuration AMAX panel 4000 / AMAX panel 4000
EN
2013.07 | 03 | F.01U.267.113 Quick Start Guide Bosch Sicherheitssysteme GmbH