Bosch Solution 6000-IP User manual

Solution 6000-IP
Security System
User Guide
EN
Security Systems

Solution 6000-IP
2Bosch Security Systems 10/22 BLCC615U
User Guide
Copyright Notice
Unless otherwise indicated, this publication is the copyright
of Bosch Security Systems Pty Ltd (“Bosch”). All rights are
reserved.You may download a single copy of this publication.
By downloading the publication you agree that you will: (i) only
use the publication for your own reference; (ii) not commercially
exploit or charge any person for the use of the publication;
and (iii) not modify the publication in any way without the
prior written permission of Bosch. Except as specified above or
where authorised by the Copyright Act 1968 (Cth), no part of
this publication may be reproduced, transmitted, modified or
stored in any form or by any means, without the prior written
permission of Bosch.
Trademarks
Throughout this document trademark names may have been
used. Rather than put a trademark symbol in every occurrence
of a trademark name, we state that we are using the names only
in an editorial fashion and to the benefit of the trademark owner
with no intention of infringement of the trademark.
Notice of Liability
While every effort has been taken the accuracy of this document,
neither Bosch Security Systems Pty Ltd nor any of its official
representatives shall have any liability to any person or entity
with respect to any liability, loss or damage caused or alleged
to be caused directly or indirectly by the information contained
in this book. Should you find any error on inconsistency, please
notify us accordingly.
Bosch Security Systems Pty Ltd reserves the right to make
changes to features and specifications at any time without prior
notification in the interest of ongoing product development and
improvement.
Warnings
1) This product must be installed by a qualified and
licensed security installer.
2) This product may not perform as expected if
installed incorrectly.
3) Some features of this product, including but
not limited to MyAlarm Back to Base reporting,
MyAlarm SMS, MyAlarm Email Reporting,
MyAlarm Voice Reporting , MyAlarm Push
Reporting and Automatic Time and Date
Adjustments require a working IP connection to
operate.
4) Australian standard AS 2201 requires regular
service by qualified and licensed security persons
and regular user testing. Please consult your
security alarm company for further details.
5) Incorrect programming of parameters can result
in operation contrary to what may be desired.
6) Leave the mains adapter plugged in at all times.
7) Leave IP connected in at all times under normal
conditions.
8) The Product Identification Label for this product
which is supplied in the resistor pack, must be
affixed to the outside of the enclosure during
installation.
Intrusion Control Panel
Designed In
Australia
Solution 6000-IP
RoHS
9
9) This equipment shall not be set up to make
automatic calls to the Telecom‘111’Emergency
Service.
Notice to Owner
Thankyou for selecting the Solution 6000-IP Security Control Panel for your security needs. Your system includes many advanced
features and functions which will be programmed and configured by your security consultant during installation. Depending on the
configuration, and your access level, you may have the ability to program certain features within the system to suit changes in your
security needs. For example you may wish to change a User Name or PIN number when a staff member leaves.
This manual explains all aspects of system operation as well as detailling the various programming options available to you. We ask that
you take the time to read this manual carefully and that you have your installer explain the basic system operation and configuration
to you when the installation is complete.

3Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Copyright Notice ................................................................... 2
Trademarks............................................................................. 2
Notice of Liability .................................................................. 2
Notice to Owner........................................................................... 2
Program Menu Tree..................................................................... 5
Introduction ................................................................................. 6
Features......................................................................................... 6
User’s Guide.................................................................................. 6
Reporting Alarms ........................................................................ 7
About the Keypad ....................................................................... 7
Keypad Keys ........................................................................... 7
Status Icons / LED’s................................................................ 8
Keypad Tones ......................................................................... 8
Basic System Operation.............................................................. 9
Turning An Area All On......................................................... 9
Turning An Area Part On / Part 2 On .................................. 9
Turning The System Off ........................................................ 9
Silencing Alarms.................................................................. 10
Automatic Arming............................................................... 10
Programming Text Using The Keypad ............................. 10
Duress or Silent Alarms ...................................................... 11
System Programming ............................................................... 11
Erase User......................................................................................11
PIN Numbers ........................................................................ 11
Change Own PIN ........................................................................11
Change Other PIN ......................................................................11
Add PIN ..........................................................................................12
Delete PIN .....................................................................................12
Tokens.................................................................................... 12
Add Token .....................................................................................12
Delete Token ................................................................................13
Token Status.................................................................................13
Edit Token......................................................................................13
RF Keyfob .............................................................................. 13
Add Keyfob ...................................................................................13
Delete Keyfob ..............................................................................14
User Name.....................................................................................14
Area Assignment ........................................................................14
User Options.................................................................................14
TimeZones ............................................................................15
TimeZone Access........................................................................15
Door Assignment .......................................................................15
User Expire Date..........................................................................15
Fingerprints .......................................................................... 16
Add Fingerprint...........................................................................16
Delete Fingerprint......................................................................16
Fingerprint Status.......................................................................17
Areas ......................................................................................17
Area Status....................................................................................17
Turn Area On/Off ........................................................................17
Turn All Areas On........................................................................18
Turn All Areas Off........................................................................18
Move To Area................................................................................18
Chime On/Off...............................................................................18
Chime Mode.................................................................................19
Area Name ....................................................................................19
Part Mode 1 Name .....................................................................19
Part Mode 2 Name .....................................................................19
Auto Arming.................................................................................20
Exit Time ........................................................................................20
Entry Time 1..................................................................................20
Entry Time 2..................................................................................21
Part Entry Time ............................................................................21
Inputs..................................................................................... 22
Zone Status...................................................................................22
Zone Array.....................................................................................22
Bypass Zones ...............................................................................22
Set Chime Zones.........................................................................23
Set Part 2 Zones ..........................................................................23
Smoke Sensor Reset ..................................................................24
Zone Name ...................................................................................24
Walk Test All Zones.....................................................................24
Walk Test A Single Zone ...........................................................25
Outputs ................................................................................. 25
Output Status...............................................................................25
Turn Output On/Off...................................................................25
Output Array ................................................................................26
Door Status...................................................................................26
Door Array.....................................................................................26
Door Control ................................................................................27
Output Name...............................................................................27
Door Name ...................................................................................27
External Siren Test ......................................................................28
Internal Siren Test.......................................................................28
Strobe Test ....................................................................................28
Fire Siren Test ...............................................................................28
Communication / Reporting..............................................29
Check Web Email ........................................................................29
Email System Log .......................................................................29
Start Direct Connect..................................................................29
Register Customer......................................................................29
Send Test Report.........................................................................29
Devices and Optional Modules......................................... 30
Device Status ...............................................................................30
Keypad Volume ...........................................................................30
Keypad Contrast .........................................................................30
Keypad Backlight........................................................................30
Name...............................................................................................30
System Events ...................................................................... 31
Panel Status..................................................................................31
System Trouble............................................................................32
History Log....................................................................................34
TimeZone Array...........................................................................34
Set Date And Time .....................................................................35
Volume ...........................................................................................35
TimeZones ............................................................................ 35
Name...............................................................................................35
Time.................................................................................................35
Day...................................................................................................36
TimeZone Options .....................................................................36
Name...............................................................................................36
Start / Stop Day ...........................................................................37
Keypad Hi/Lo Temp....................................................................37
Site Name......................................................................................37
Walk Test All Zones.....................................................................37
Battery Test ...................................................................................38
Installation Details .................................................................... 40
Contents

Solution 6000-IP
4Bosch Security Systems 10/22 BLCC615U
User Guide
This page left intentionally blank

5Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Program Menu Tree
Table 1: shows all of the system options in a tabular format. Each option can be access by pressing the Menu key and
then drilling down using the arrow and OK keys until the required option is listed on the display. A quick way to jump to
a particular option is to press the Menu key followed by the specific option number. You may be asked to enter your PIN
when accessing some options and some options are only available to users with Master Code authority.
Example:
To change the exit time, enter programming mode, then enter [MENU] + [2] + [8] + [0] and follow the on screen prompts.
1Access 2 Areas 3 Inputs 4 Outputs
1-0 Commands 2-0 Commands 3-0 Command 4-0 Commands
1-0-0 Erase User 2-0-0 Area Status 3-0-0 Zone Status 4-0-0 Output Status
2-0-1 Turn Area On/Off 3-0-1 Zone Array 4-0-1 Turn Output On/Off
1-1 PIN Codes 2-0-2 Turn All Areas On 3-0-2 Bypass Zones 4-0-2 Output Array
1-1-0 Change Own PIN 2-0-3 Turn All Areas Off 3-0-3 Set Chime Zones 4-0-3 Door Status
1-1-1 Change Other PIN 2-0-4 Move To Area 3-0-4 Set Part 2 Zones 4-0-4 Door Array
1-1-2 Add PIN 2-0-5 Chime On/Off 3-0-5 Smoke Sensor Reset 4-0-5 Door Control
1-1-3 Delete PIN 2-0-6 Chime Mode 3-1 Zone Properties 4-1 Output Properties
1-2 Token 2-1 Area Properties 3-1-0 Zone Name 4-1-0 Output Name
1-2-0 Add Token 2-1-0 Area Name
1-2-1 Delete Token 2-1-6 Part Mode 1 Name 3-9 Input Testing 4-2 Door Control
1-2-2 Token Status 2-1-7 Part Mode 2 Name 3-9-0 Walk Test All Zones 4-2-0 Door Name
1-2-3 Edit Token 2-1-8 Auto Arming 3-9-1 Walk Test A Zone 4-9 Output Testing
1-3 RF Keyfob 2-8 Timers 4-9-0 External Siren Test
1-3-0 Add Keyfob 2-8-0 Exit Time 4-9-1 Internal Siren Test
1-3-1 Delete Keyfob 2-8-1 Entry Time 1 4-9-2 Strobe Test
2-8-2 Entry Time 2 4-9-3 Fire Siren Test
1-4 User Properties 2-8-3 Part Entry Time
1-4-0 User Name
1-4-1 Area Assignment
1-4-2 User Options
1-4-4 TimeZone Access
1-4-5 Door Assignment
1-4-6 User Expire Date
1-8 Fingerprint
1-8-0 Add Fingerprint
1-8-1 Delete Fingerprint
1-8-2 Fingerprint Status
5 Comms 6 Devices 7 System
5-0 Commands 6-0 Commands 7-0 Commands
5-0-3 Check Web Email 6-0-0 Device Status 7-0-0 Panel Status
5-0-4 Email System Log 6-0-7 Keypad Volume 7-0-1 System Trouble
5-0-5 Start Direck Link 6-0-8 Keypad Contrast 7-0-2 History Log
5-0-8 Register Customer 6-0-9 Keypad Backlight 7-0-6 TimeZone Array
5-9 Comms Test 6-1 Keypads & Readers 7-1 Clock
5-9-0 Send Test Report 6-1-0 Name 7-1-0 Set Date And Time
6-1-9 WiFi Settings 7-4 Siren
6-5 GSM/GPRS Module 7-4-2 Volume
6-5-0 GSM/GPRS Status 7-5 TimeZones
7-5-0 Name
7-5-1 Time
7-5-2 Day
7-5-3 TimeZone Options
7-6 Holidays
7-6-0 Holiday Name
7-6-1 Start Stop Dates
7-7 System Options
7-7-3 Keypad Hi/Lo Temp
7-7-7 Site Name
7-9 System Testing
7-9-0 Walk Test All Zones
7-9-1 Battery Test
Table 1: Control Panel Menu Tree

Solution 6000-IP
6Bosch Security Systems 10/22 BLCC615U
User Guide
Introduction
Your system helps to secure life, property and investments
against fire, theft and bodily harm. It consists of a keypad
(or keypads), sensors such as motion detectors or devices
located on doors and windows, and other sensing devices
designed to detect the presence of smoke or combustion.
The location and quantity of sensing devices will have
already been discussed with you by your alarm installer.
Control of your security system is achieved through
the unique graphic keypad, which displays all system
information in written text and graphical symbols. Its
versatility and ease of operation, make it ideal for any home
or business application.
Features
Listed below are the main features of the Solution 6000-IP
control panel.
Up to 144 Fully Programmable Zones
Up to 16 Access Doors
Fire Alarm Verification
Up to 990 User PINs
Up to 37 Programmable Outputs
GSM/GPRS/Ethernet Reporting Options
Optional Fingerprint Readers
Supervised Siren Driver
16 Programmable TimeZones
Up To 8 Areas (Common Area Programmable)
Up To 16 Fully Supervised Keypads / Readers
National Broadband Network / IP Ready
Keyswitch Input (Programmable)
2000 Event History Memory
EMI / Lightning Transient Protection
Programmable Via Keypad
Remote Programmable Via RAS Software
Automatic Test Reports
User’s Guide
This user’s guide shows you how to use and maintain
your security system. It covers basic functions, such as
turning the system on and off as well as some general
programming. More complex programming and system
configuration should be performed by your installer.
Many of the programming functions described in this
guide will have already been programmed by your alarm
installer while others may need to be programmed or
changed by you. Depending on your particular system
configuration some features described in this manual
may not be available. Please discuss this with your alarm
installer.
Functions outlined in this user guide may require you to
enter your PIN (Personal Identification Number), so make
sure you choose a number that is easy for you to remember
but hard for someone else to guess. For security reasons
do not write this PIN down or give it to anyone else. If more
than one person needs to operate the system then you
should create a different PIN code for them if this has not
been done by your installer. This guide will explain how to
do this. See “MENU 1-1-2”on page 12.
Please take the time to familiarise yourself with the
following terms before reading the rest of this guide.
Zones
A‘Zone’is a detection device, or group of devices connected
to your security system. Zones are identified by the area
they monitor, such as a front door, bedroom window or
hallway.
Faulted Zones
When a zone (such as a door or window) is closed, it is
said to be ‘normal’. When the door or window is open, the
zone is said to be ‘faulted’. When you turn your system
on, you will usually want all of the zones in your system
to be normal, although, you can turn your system on with
faulted zones.
Zones Types
There are two basic types of zones, Non 24-hour and 24-
hour. See below.
Non 24-Hour Zones
Non 24-hour zones respond to alarm conditions
depending upon whether the system is turned on or off.
They are programmed to either respond instantly to alarm
conditions or to provide a delay for you to reach the keypad
and turn the system off. Various zones will be located
throughout your premises.
When you turn your system on, you have the option of
turning on all zones (All On), or just some of the zones (Part
On). Refer to the basic system operation section for more
information.
Bypassed Zones
A zone which has been bypassed will remain unarmed
when the system is armed. You may need to bypass a
zone when doing renovations in the building or if a sensor
becomes faulty. Bypassed zones will reset the next time
the system is disarmed.
24-Hour Zones
24-hour zones are always on and cannot be turned off,
even when the system is turned off (disarmed). There are
two types of 24-hour zones, fire zones and non-fire zones.
What Is An Area?
The control panel comes defaulted and programmed for a
single area configuration (Area 1), therefore, all zones are
assigned to Area 1. The alarm system can be divided into 8
individual areas. In this case, the security company would
assign different sensors (zones) to each area according to
the area they belong.
Example:
Partitioning a commercial business to 4 individual areas
may be as follows:
Area 1 – Main entry/exit area
Area 2 – Sales
Area 3 – Administration
Area 4 – Dispatch

7Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Each area can be controlled individually as if they were
separate alarm systems.
All On
When you turn an area All On, you are turning on all non 24-
hour zones, both interior (motion detectors) and perimeter
(doors and windows) of the building.
Part On
When you turn an area Part On, you only turn on some of the
non 24-hour zones. Your security company will program
which zones are included in this mode. Part zones may
include only the perimeter (doors and windows) of your
system, or sensors in other areas of your premises. Check
with your security company to learn which zones are Part
zones.
Reporting Alarms
Your system may be programmed to send reports and
it does this over a working IP connection either through
Ethernet,WiFior througha cellularradio moduledepending
on your installation (check with your security company).
Your system makes repeated attempts to send reports to
your security company. If your system fails to report, the
keypad will display the ‘service’symbol.
About the Keypad
Your keypad has 20 keys or buttons. The buttons allow you
to input instructions and navigate the menu screens as
required. Some buttons have a secondary function which
is activated by holding them down for two seconds.
Each button’s function is described below:
Keypad Keys
Key Description
to
The numeric keys allow you to enter
you numbers when required.
Use the [MENU] and the numeric keys
to enter commands. The [MENU] key
is also used to go back one level when
navigating through menus or to exit a
programming location without saving
changes.
The [ON] key allows you to turn an area
or output on. If your system has been
partitioned press and hold the [ON]
key for two seconds to turn all areas on
at the same time.
The [PART] key allows you to turn an
area Part On. This key can also be used
to bypass a zone or multiple zones
when you press and hold for two
seconds.
Key Description
The [OFF] key allows you to turn an
area or output off. If your system has
been partitioned press and hold the
[OFF] key for two seconds to disarm to
disarm all areas.
The [OK] key allows you to save any
changes and exit the command.
The [MAIL] key allows you to read
stored mail. This key can also be used
to a test report when you press and
hold for two seconds.
The [] key allows you to move the
cursor left when programming text.
The [] key allows you to move the
cursor right when programming text.
The [] key allows you to navigate
through menus or to toggle characters.
The [] key allows you to navigate
through menus or to toggle characters.
Pressing The [] key will display current
trouble conditions when the area that
the keypad is displaying is disarmed.
+
for 2 sec
Pressing the [] and [] keys together
and holding them down for 2 seconds
will cause a Panic alarm to be triggered.
If programmed the sirens will sound
and the monitoring station will be
notified.
+
for 2 sec
Pressing the [] and [] keys together
and holding them down for 2 seconds
will cause a Fire alarm to be triggered. If
programmed the sirens will sound and
the monitoring station will be notified.
+
for 2 sec
Pressing the [] and [] keys together
and holding them down for 2 seconds
will cause a Medical alarm to be
triggered. If programmed the sirens
will sound and the monitoring station
will be notified.
Table 2: Keypad Keys and Their Function
Figure 1: Keypad Emergency Alarm Triggers

Solution 6000-IP
8Bosch Security Systems 10/22 BLCC615U
User Guide
Status Icons / LED’s
The following table describes the function of each of
the status icons and indicator lights. Some keypads and
readers also include a blue indicator which is used when
controlling doors or user access.
Icon Status Meaning
The keypad can display which areas (1 – 8) are
turned on or off via the Area Icon Indicators. This
option needs to be enbled by your installer,
On The area is turned All On or Part On
Off The area is turned Off
Flashing
Fast The area has an alarm
On System power is normal
Flashing System power is missing
Flashing A fire alarm is active
Off No fire alarm
On Fire alarm in memory (Turn the area
All On and Off to clear).
Flashing A burglary alarm is active
Off No burglary alarm
On Burglary alarm in memory (Turn the
area All On and Off to clear).
On The existing service or trouble
condition has been acknowledged
Off No service or trouble conditions exist
Flashing
A service or trouble condition is
present that has not been acknowl-
edged
On The area is turned Part On
Off The area is not turned Part On
On The area is turned off.
Off The area is turned All On or Part On
On The area is turned All On
Off The area is turned Off
On You have mail waiting to be read
Off No Mail
On Area is ready to turn All On /Part On
Off Not ready, Zone Open
Red
LED
On All On or Part On
Flashing Alarm
Green
LED
On Area is not All On
Flashing Zone is Faulted
Red &
Green
LED
Flashing Installer programming mode is active
Off User Programming Mode is Active
Icon Status Meaning
Blue
LED
On Door Locked
Fast
Flash Door Unlocked
2
Flashes Door Unlocked by TimeZone
Off Door Assignment not programmed
The WiFi enabled keypad or module
has successfully connected to your
local WiFi network.
The WiFi enabled keypad or module
is not connected to your local WiFi
network.
Table 3: Status ICONs, LED Indicator’s and Their Meanings
Keypad Tones
Your keypad emits several distinct tones and displays text
to alert you to system events. Additional bells or sirens
may also be connected to your system. Bells or sirens
mounted on the exterior of your premises alert neighbours
to emergencies and provide an audible guide for police
and fire fighters.
Type Meaning
Fire
Alarm
Tone
When a fire zone sounds an alarm, the
keypad will sound 3 seconds on and 2
seconds off (repeat).
Burglary
Alarm
Tone
When a burglary zone activates while your
system is turned on, your keypad emits a
continuous siren tone. It sounds for the
time set by your security company.
Trouble
Tone
When a system component is not
functioning properly, your keypad sounds
4 fast short beeps followed by a 5 second
pause (repeat).
Key
Press
Tone
Pressing any key on the keypad sounds one
short beep, indicating that the key press is
accepted.
Entry
Delay
Tone
When you enter the premises through
a zone programmed for entry delay, the
keypad sound a Hi/Low tone to remind you
to turn off the area. If the area is not turned
off before the entry delay expires, an alarm
condition will sound and a report may be
sent to your alarm company.
Exit
Delay
Tone
After you turn an area All On, the keypad will
sound 1 short beep every second. During
the last 10 seconds fast short beeps will be
heard. If you don’t exit before the delay time
expires and an exit delay door is faulted, an
alarm occurs.

9Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Error
Tone
If you enter an incorrect value when
programming, the keypad will sound a 2
second tone.
Menu
Mode
The keypad will sound a Lo/Hi tone to
indicate you have entered MENU Mode and
a Hi/Lo tone to indicate you have exited
MENU mode.
Chime
Tone
The keypad sounds fast short beeps to alert
you when a zone programmed for chime is
faulted or unsealled.
Table 4: Keypad Tones and Their Meanings
Figure 2: CP736B Graphic Keypad
Basic System Operation
Turning An Area All On
Use this function to turn an area All On. The control panel
is factory defaulted for one area. As soon as you turn an
area on, exit time will start. Exit time allows you to exit
the premises without sounding an alarm. Your security
company or a master PIN user can program the length of
exit delay time.
1. Make sure that all zones are normal (not faulted).
2. Enter your PIN, then press the [ON] key.
If your PIN is valid and if all zones are normal, exit delay
time will start. You should leave now. If your control
panel detects a faulted zone, you should return it to
normal, or bypass the zone.
During exit delay, you may stop the area from turning
on by entering your PIN followed by the [OFF] key.
3. To turn the system (or area) off, enter your PIN, then
press [OFF].
Turning An Area Part On / Part 2 On
Use this function to turn an area Part On or Part 2 On. The
control panel is factory default only for one area. Part On
and Part 2 On turns on only part of the area, leaving the
rest of the area turned off.
Only the security company can program which zones are
monitored for Part On. A master user can program which
zones are monitored when a user turns an area Part 2 On.
Once you have turned an area Part On or Part 2 On, exit
delay time starts to count down. You should leave all zones
that are active before exit delay time expires. Leaving
active zones after exit delay expires causes an alarm event.
Use Part On or Part 2 On only when you want part of an
area turned on.
1. Make sure that all zones are normal (not faulted).
2. Enter your PIN, then press the [PART] key.
If your PIN is valid and if all zones are normal, the
keypad will prompt you to select Part On or Part 2 On.
3. Using the arrow keys, highlight Part On or Part 2 On
then press [OK].
Exit delay time will start. You should leave now. If
your system has a faulted zone, you should return it to
normal, or bypass the faulted zone.
During exit delay, you may stop the system from
turning Part On by entering your PIN followed by the
[OFF] key.
4. When exit time has expired, the keypad will display
the Part On icon.
5. To turn the system off, enter your PIN, then press
[OFF].
Turning The System Off
Whenthesystemis on,youmust enterthroughadesignated
entry door to prevent an alarm. Opening a designated door
(e.g. front door) will start entry time. During entry time, the
keypad will sound the Hi/Lo tone to remind you to turn the
system off. To turn off, enter your PIN followed by the [OFF]
key before the entry delay time expires.
If you enter through the wrong door or fail to turn the
system off before the entry delay time expires, you may
cause a false alarm. If this situation arrises, silence the
alarm by entering your PIN followed by the [OFF] key and
call your security company to let them know that it is not
an emergency situation.
1. Enter your PIN + [OFF] to turn the system (or area)
off. The keypad will no longer display the‘Lock’ or
‘Part’ icons.

Solution 6000-IP
10 Bosch Security Systems 10/22 BLCC615U
User Guide
Silencing Alarms
When the control panel has registered an alarm, the keypad
(s) and sirens will sound to alert personnel that an alarm
occurred. The keypad will scroll in the display all alarms on
the keypad display for visual feedback. If you enter your
PIN before the system dials your security company, the
alarm report is cancelled (if programmed).
1. Enter your PIN + [OFF] to silence any alarm and turn
the system off.
The keypad will continue to scroll all alarm events that
caused the alarm. This is called alarm memory.
2. To clear alarm memory, turn the area on and off
again (eg. PIN + [ON] + PIN + [OFF]).
Automatic Arming
Your system may have been programmed to automatically
arm itself at a certain time of the day.
If for some reason you are still in the building when the
auto arming is taking place then it is possible to extend
or delay the auto-on time (automatic arming time) by
one hour simply by entering your PIN + [OFF] during
the auto-on pre-alert time. The auto-on pre-alert time
sounds the keypad buzzer to warn you that the system will
automatically turn All On.
Example:
If the control panel is programmed to automatically turn
All On at 6:00pm and the auto-on pre-alert time starts
beeping the keypad at 5:55pm, entering your PIN between
5:55pm and 6:00pm will delay the auto-on time by one
hour and the auto-on pre-alert time will again commence
at 6:55pm. Therefore the system will automatically turn All
On at 7:00pm.
Programming Text Using The Keypad
When programming text via the keypad, various keys on
the keypad operate differently.
A group of characters is assigned to each of the numeric
keys on the keypad. Pressing the same numeric key again
will toggle to the next character assigned to the key (eg.
Press the [2] key will display the ‘A’ character, press the [2]
key again will toggle to the ‘B’ character, press the [2] key
again will toggle to the‘C’ character etc).
Once the correct character is display use the arrow keys to
move to the next letter of the word you are entering. The
key assignments are identical to those found on most fixed
and mobile phones.
When programming text, each numeric key represents a
different group of characters.
Pressing the same numeric key repeatedly will step you
through the available characters assigned to the key. The
text key layout is the same as most phones. Refer to the
table below for detailed character information.
Refer to the following table for more information.
Key Characters Assigned To Each Numeric Key
1 . , ? ! - & ` 1
2 A B C a b c 2
3 D E F d e f 3
4 G H I g h i 4
5 J K L j k l 5
6 M N O m n o 6
7 P Q R S p q r s 7
8 T U V t u v 8
9 W X Y Z w x y z 9
0 SPACE 0
Scroll Up through entire character list
Scroll Down through entire character list
Move to left one character position
Move to right one character position
OFF Clear from cursor postiion to end of line
Table 6: Text Keypad Character Set
Once the desired character is displayed press the right []
arrow key to move to the next character position. To save
programming changes, press [OK], or press [MENU] to exit
without saving.
The following additional special characters are available
by scrolling using the up and down arrow keys.
+ - @ # $ “ & % * : ( ) / < > =

11Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Duress or Silent Alarms
A Duress or Silent Panic alarm can be easily triggered via
the keypad if you are being forced to operate the system
against your will.
To trigger a duress, enter your normal user PIN followed by
the last 2 digits of your user PIN followed by the ON or OFF
key. See the following examples.
1. If your PIN is 2580, to send a duress report when the
area is off, Enter, [2] + [5] + [8] + [0] + [8] + [0] + [OK]
or [ON].
2. If your PIN is 2580, to send a duress report when
the area is on, Enter, [2] + [5] + [8] + [0] + [8] + [0] +
[OFF].
i
Note
Duress alarms are triggered by entering the user PIN
followed by the last 2 digits of the user PIN followed
by the ON or OFF key.
System Programming
i
Note
Someoftheexamplesshowninthefollowingsection
assume that you are already in programming
mode. To enter programming mode simply enter
your PIN and press the MENU key on the keypad.
Access > Commands >
Erase User MENU 1-0-0
This menu allows the installer or master user, to erase
another user. When a user is erased, it will return back to
factory default all information relating to the following:
PIN
Token ID
RF Keyfob ID
Fingerprint ID
Name
TimeZone Access
Door Assignment
Area Assignment
Enter [MENU] + [1] + [0] + [0].
1. Use the arrow keys to highlight the user to be erased
then press [OK].
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Verify the user name to be erased and press [OK].
To abort press [MENU].
To erase Ur1
John Smith
press OK.
Press OK or MENU
PIN Numbers
Access > PIN Codes >
Change Own PIN MENU 1-1-0
Thismenu letsyouchange yourown PIN. It isrecommended
that you write down your old PIN and the new one before
you begin. The new PIN must have the same number of
digits as your old PIN unless your installer has enabled the
variable length PIN option. Once the change is complete
you should destroy the written copy.
At factory default, each PIN is fixed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580. Only the
security installer can change the PIN length.
Enter programming mode (PIN + MENU) then,
1. Ensure that the system (or area) is turned off.
2. Enter your PIN, and then press [MENU] + [1] + [1] +
[0]. The keypad will prompt you to enter a new PIN.
Enter New PIN For Ur2
Debbie Smith
Press OK or MENU
3. Enter your new PIN, and then press [OK]. If an error
tone sounds, try a different PIN. The keypad will
now prompt you to enter your new PIN again.
Conrm New PIN Ur2
Debbie Smith
Press OK or MENU
4. Enter your new PIN again.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving your PIN has now been changed.
Access > PIN Codes >
Change Other PIN MENU 1-1-1
If you have a master PIN, this menu allows you to change
somebody else’s PIN. It is recommended that you write
down the old PIN and the new one before you begin. Once
the change is complete you should destroy the written
copy. The new PIN must have the same number of digits
as the old PIN.
At factory default, each PIN is fixed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580.
Enter programming mode (PIN + MENU) then,

Solution 6000-IP
12 Bosch Security Systems 10/22 BLCC615U
User Guide
Ensure that the system (or area) is turned off.
1. Press [MENU] + [1] + [1] + [1]. The keypad will display
a list of available users that you can change their
PIN.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the [] and [] keys to select the user that you
want to change the PIN, then press [OK] to select.
Alternatively, you can enter the user number you
want to change, then press [OK].
Enter PIN for Ur2
Debbie Smith
Press OK or MENU
3. Enter the new PIN.
If an error tone sounds, try a different PIN.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes >
Add PIN MENU 1-1-2
This menu allows a Master user to add a PIN to a new user.
A Master user can only program a new PIN for those users
that have been assigned to the same area(s) as the Master
user.
At factory default, each PIN is fixed to 4 digits in length.
The default PIN for User 1 (Master user) is 2580.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [1] + [2].
A list of users will display on the keypad.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the [] and [] keys to select the user that you
want to add a PIN, then press [OK] to select.
Alternatively, you can enter the user number you
want to add, then press [OK].
The keypad will prompt you to enter the new pin.
Enter New PIN For Ur3
User 3 Name
Press OK or MENU
3. Enter the new PIN for the user you have selected.
If an error tone sounds, try a different new PIN.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > PIN Codes >
Delete PIN MENU 1-1-3
This menu allows a Master user the ability delete other
users PIN’s. A Master user can only delete a PIN for those
users that have been assigned to the same area(s) as the
Master user. A Master user cannot delete their own PIN.
Enter programming mode (PIN + MENU) then,
1. Make sure that the system is turned off.
2. Press [MENU] + [1] + [1] + [3].
The keypad will list all users that you can delete.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
3. Use the [] and [] keys to highlight the user whose
PIN you want to delete, then press [OK] to select.
Alternatively, you can enter the user number you
want to delete, then press [OK].
Press OK To Delete PIN
For Ur2
Debbie Smith
Press OK or MENU
4. Press [OK] again to delete the PIN, or press [MENU]
to cancel.
Tokens
This section outlines how to add and delete token cards
that allow an alternate method for users to turn the system
on and off via a prox reader enabled keypad. The system
can also be configured to automatically open a door if
it has been fitted with an electric door lock. You should
discuss this feature with your installer for more details on
your particular installation.
A token is a small plastic tag card that has a unique ID. A
user can place the token card in front of a keypad that has
a built-in token reader to turn the system or specific areas
on and off.
Access > Token >
Add Token MENU 1-2-0
This menu allows a Master user the ability to add a new
token for those users that have been assigned to the same
area(s) as the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [2] + [0].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user that you

13Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
want to add a token for, then press [OK] to select.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
3. If you are using a keypad with built in reader the
system will prompt you to present the token to the
keypad. Once the token is presented the keypad will
beep and return to the menu.
To add token for Ur1
JOHN SMITH present new
token
Press OK or MENU
A Master user can only delete a token for those users that
have been assigned to the same area(s) as the Master user.
Access > Token >
Delete Token MENU 1-2-1
This menu allows a Master user the ability to delete a token
for those users that have been assigned to the same area(s)
as the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [2] + [1].
A list of users will display on the keypad.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the [] and [] keys to select the user who’s
token you want to delete, then press [OK] to select.
Press OK To Delete Token
For Ur1
John Smith
Press OK or MENU
3. When prompted press the [OK] key to confirm token
deletion.
Access > Token >
Token Status MENU 1-2-2
This menu allows a Master user the ability to identify a
token which has been programmed into the system. Only
tokens that have been assigned to the same area(s) as the
Master user can be identified.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [2] + [2].
The system will prompt you to present the token to
the keypad.
2. Once the token is presented the system will display
the owner of the token.
Token belongs to Ur2
Debbie Smith
Press OK or MENU
Access > Token >
Edit Token MENU 1-2-3
This menu allows a Master user the ability to delete a token
for those users that have been assigned to the same area(s)
as the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [2] + [3].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user who’s
token you want to delete, then press [OK] to select.
Edit Token Ur2
000000000
Press  OK to SAVE
3. When prompted press the [OK] key to confirm token
deletion.
RF Keyfob
This section outlines how to add and delete RF keyfobs
which provide an alternate method for users to turn an
area(s) on and off. The RF keyfob must be compatible with
the RF Receiver that has been installed by the security
company.
Access > RF Keyfob >
Add Keyfob MENU 1-3-0
This menu allows the security installer or a master user to
program the user’s keyfob ID number.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [3] + [0].
A list of users will display on the keypad.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the [] and [] keys to select the user that you
want to add the RF keyfob ID, then press [OK] to
select. Alternatively, you can enter the user number
you, then press [OK].
The keypad will prompt you to enter the RF keyfob

Solution 6000-IP
14 Bosch Security Systems 10/22 BLCC615U
User Guide
ID number:
Enter Keyfob ID Ur16
User 16 Name
000000000
Press OK or MENU
3. Enter the RF Keyfob ID Number
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > RF Keyfob >
Delete Keyfob MENU 1-3-1
This menu allows the security installer or a master user to
delete the RF keyfob ID that has been assigned to a user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [3] + [1].
A list of users will display on the keypad.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the [] and [] keys to select the user that you
want to delete the keyfob, then press [OK] to select.
Alternatively, you can enter the user number, then
press [OK].
Press OK To Delete
Keyfob For Ur1
009553507
Press OK or MENU
3. Press [OK] to delete the RF Keyfob ID number and
exit, or press [MENU] to exit without saving.
Access > User Properties >
User Name MENU 1-4-0
This menu allows the master user to program the user’s
name. A maximum of 20 characters can be entered.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [4] + [0].
A list of users will display on the keypad.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. To program the user name, use the [] and [] keys
to select the user that you want to program, then
press [OK] to select. Alternatively, you can enter the
user number you want to program, then press [OK].
The keypad will display the current user name.
User Name Ur1
User 1 Name
Press  OK to SAVE
3. Use the [] and [] keys to scroll the cursor left
and right across the user name text. Use the [] and
[] keys to scroll through the different characters
available. To clear all text from the cursor position,
press the [OFF] key.
4. When the user name is complete, press [OK] to save
and exit, or press [MENU] to exit without saving.
Access > User Properties >
Area Assignment MENU 1-4-1
This menu allows the master user to program which areas
(1 to 8) a user can access. Each user can be assigned to
one or multiple areas. The master user is restricted and can
only assign another user to any one or multiple areas that
the master user has been assigned to. At factory default,
each user is assigned to operate Area 1.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [4] + [1].
A list of users will display on the keypad.
2. To assign areas to a user, use the [] and [] keys to
select the user that you want to program, then press
[OK] to select. Alternatively, you can enter the user
number you want to program, then press [OK].
The keypad will display which areas the user has
been assigned to.
Security System
Area 2 Name
Area 3 name
Press  OK ON OFF MENU
3. Use the [] and [] keys to select the area that
you want to assign to the user. Press the [ON] key
to assign the user to the area (√ will display) or
press the [OFF] key to disable the user from the
corresponding area (√ will no longer display).
4. Repeat Step 3 until you have assigned the user to all
areas that are required.
5. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Access > User Properties >
User Options MENU 1-4-2
This menu allows the master user to set or change various
options for other users on the system. You should discuss
these options with your installer before making changes.
Follow the procedure below to configure the required
options.

15Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
1. Enter your Master PIN + [MENU].
2. Enter [1] + [4] + [2] + [OK].
The keypad will display the list of current options.
Options with a preceeding tick mark are selected.
 Master User
Reserved
Arm Only
Press  OK ON OFF MENU
3. Use the [] and [] keys to highlight the feature that
you want to program, then use the [ON] and [OFF]
keys to turn on and off the features as required.
4. When all user options are programmed, press [OK] to
save and exit, or press [MENU] to exit without saving.
TimeZones
Timezones can be used to restrict users from operating
doors or from controlling the alarm system outside given
times of the day, days of the week or during holidays.
A master code holder is able to change the timezone
parameters so they can control the access times for a given
user. If a resticted user tries to operate the system outside
their assigned timezone then access will be denied.
See MENU 7-5-0 for more information on timezone
programming.
Access > User Properties >
TimeZone Access MENU 1-4-4
This menu is used to assign a user to a timezone. Timezones
can be used to restrict a users access to be within specific
times of the day and or days of the week. Each user can
only be assigned to one timezone. Setting this option to
timezone 1 will give the user 24 hour access to the system.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [4] + [4] and select the user
from the list then press [OK].
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Using the numeric keys, enter the timezone.
Valid entries are 1 – 16 or 0 to disable.
TimeZone Access Ur1
01 - 24 Hour TimeZone
Press  0-9 OK to SAVE
3. Press [OK] to save and exit or press [MENU] to exit
without saving.
Access > User Properties >
Door Assignment MENU 1-4-5
This menu allows you to assign each user to one or more
door groups. A door assignment is used to allow and/or
restrict which users have access to various system outputs.
These outputs can be used to control door strikes, gates or
roller doors etc.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [4] + [5] and select the user
from the list then press [OK].
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the up and down arrow keys to highlight the
door group then press the [ON] key to select or the
[OFF] key to deselect.
Door 1 Name
Door 2 Name
Door 3 Name
Press  OK ON OFF MENU
3. Repeat Step 2 until all required door groups are
programmed, then press [OK] to save and exit or
press [MENU] to exit without saving.
Access > User Properties >
User Expire Date MENU 1-4-6
This menu allows you to assign one or more users to expire
on a date in the future. This could be used when giving a
code to a tennant in a holday house etc. Once the expire
date is reached then all of the users credentials will cease
working and they will no longer be able to access the
system.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [4] + [6] and select the user
from the list then press [OK].
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
2. Use the [] and [] keys to program the month, day
and year. Use [] and [] keys to scroll cursor left
and right to between the month, day and year fields.
User Expire Date Ur1
Expire Date
01 Jan 2100
Press  OK to SAVE
3. Press [OK] to save and exit, or press [MENU] to exit
without saving.

Solution 6000-IP
16 Bosch Security Systems 10/22 BLCC615U
User Guide
Fingerprints
The addition of the optional fingerprint reader to your
system allows you to turn areas on and off or to open a door
simply by presenting your fingerprint to the reader. The
following steps we help you to get the best performance
from your fingerprint reader.
1) When adding or enrolling fingerprints it is is important
to place and hold your finger in the correct position while
the system records the credential. Your finger should be
placed so that the pad is making full contact with the
sensor. Do not use your fingertip.
2) Always try to present your finger in the same posistion as
you did when it was enrolled. Use the raised dimple on the
reader surface as a guide. People with smaller fingers may
find this difficult at first but with practice even they will be
able to use the reader.
3) The reader will vibrate as soon as it has completed
reading your fingerprint. Once you feel the vibrations you
should remove your finger.
4) If the reader fails on the first attempt, remove your finger
and wait for the large blue guide indicator to come on
before trying again. Whenever the reader is busy working
you may see the following screen on the keypad. Wait for a
few seconds before trying again.
Fr9 Unit Busy. Please try
later.
Press OK or MENU
5) In some cases the unit may not be able to read a finger
because the finger is cut or damaged by other means.
Extremely wet or dry fingers may also cause read errors but
these are rare. In this case you should revert to using your
PIN number on the standard keypad.
Figure 3: CM729B Fingerprint Reader
Access > Fingerprint >
Add Fingerprint MENU 1-8-0
This menu allows a master user to add a new fingerprint
for users that have been assigned to the same area(s) as
the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [8] + [0].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user that you
want to add a a fingerprint for, then press [OK] to
select.
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
3. The system will prompt you to present the finger
to the reader. If more than 1 fingerprint reader is
installed then the system will prompt you to select
the reader to learn from.
Fp9 Keypad 9 Name
Fp10 Keypad 10 Name
Fp11 Keypad 11 Name
Press  OK or MENU
4. You must hold your finger on the reader without
moving until you hear a confirmation beep which
could take up to 5 seconds.
Position Finger for Ur1
John Smith at Fp9
Press OK or MENU
i
Note
Only one fingerprint can be assigned to each user.
To change a fingerprint for an existing user, you will
need to first delete the old fingerprint first.
Access > Fingerprint >
Delete Fingerprint MENU 1-8-1
This menu allows a Master user the ability to delete a
fingerprint for those users that have been assigned to the
same area(s) as the Master user.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [8] + [1].
A list of users will display on the keypad.
2. Use the [] and [] keys to select the user who’s
fingerprint you want to delete, then press [OK] to
select.

17Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
Ur1 John Smith
Ur2 Debbie Smith
Ur3 User 3 Name
Press  OK or MENU
The keypad will display;
Press OK to delete
Fingerprint for Ur1
User 1 Name
Press OK or MENU
3. When prompted press the [OK] key to confirm
fingerprint deletion.
Access > Fingerprint >
Fingerprint Status MENU 1-8-2
This menu allows a master user the ability to identify a
fingerprint which has been programmed into the system.
Only fingerprints that have been assigned to the same
area(s) as the Master user can be identified.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [1] + [8] + [2].
The system will prompt you to present the finger to
the reader.
Position Finger at
Fp9
Press OK or MENU
2. Once the presented the system will display the user
assigned to the fingerprint.
Finger belongs to Ur1
John Smith
Press OK or MENU
Areas
The control panel has the ability to be partitioned up to
8 individual areas. This section outlines various commands
that control individual areas.
Areas > Commands >
Area Status MENU 2-0-0
This menu allows users the ability view the area status of
the current area or the status of a different area. This menu
is only available via a keypad who’s corresponding area is
turned off.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [0].
A list of available areas will display on the keypad.
A1 Main Oce
A2 Production
A3 Warehouse
Press  OK or MENU
2. Use the [] and [] keys to select the area that you
want to view the status information, then press
[OK] to select. Alternatively, you can enter the area
number, then press [OK]. The keypad will display
the area status information.
Main Oce A1
Disarmed
Press OK or MENU
If the area is turned All On, the keypad will display
the following. Note in this example 1 zone has been
bypassed.
Main Oce A1
Armed All On
1 Zones Bypassed
Press OK or MENU
If the area is turned Part On, the keypad will display:
Main Oce A1
Armed Part On
Press OK or MENU
3. To exit, press [OK].
Areas > Commands >
Turn Area On/Off MENU 2-0-1
This menu allows you to turn an area All On or off.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [1].
A list of different areas will display on the keypad.
A1 Reception Area
A2 Sales Dept 
A3 Administration Dept
Press  OK or MENU
If an area has already been turned All On or Part On,
a‘tick’ () will be displayed on the right side of the
name description (see A2 Sales Dept above).
2. Use the [] and [] keys to select the area that you
want to turn on or off, then press [OK] to select.
Alternatively, you can enter the area number you
want to turn on or off, then press [OK].

Solution 6000-IP
18 Bosch Security Systems 10/22 BLCC615U
User Guide
Areas > Commands >
Turn All Areas On MENU 2-0-2
This menu allows you to turn on all areas that your PIN
has been assigned to at the same time All On. The keypad
display below shows the area icons 1 through to 8.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [2].
The keypad will display the exit time bar to prompt
you to exit all areas. You should leave all areas now.
Area 1 Name
EXIT NOW
When exit time has expired, the keypad will display
that all areas are turned All On (Armed).
Area 1 Name
ARMED
Fri,Aug,13 5:34 pm
i
Note
Area icons will only display if programmed to
do so by your security installer.
Areas > Commands >
Turn All Areas Off MENU 2-0-3
This menu allows you to turn off all areas that your PIN has
been assigned to at the same time. However, this menu
requires at least one area that has a keypad assigned to it to
be disarmed before you can access this command.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [3].
Areas > Commands >
Move To Area MENU 2-0-4
This menu allows you to operate multiple areas from the
same keypad when the system has been partitioned.
Before operating a different area, you will need to move
the keypad to the area that you want to operate.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [4].
A list of different areas will display on the keypad.
A1 Reception Area
A2 Sales Dept
A3 Administration Dept
Press  OK or MENU
2. Use the [] and [] keys to select the area that you
want to move the keypad display to, then press
[OK] to select. Alternatively, you can enter the area
number that you want to move the keypad display
to, then press [OK].
Areas > Commands >
Chime On/Off MENU 2-0-5
Chime mode allows you to monitor a zone (or group
of zones) and to sound the keypad buzzer or activate a
programmable output when the a zone programmed for
chime is open and the system is in the disarmed state. This
can be useful when you need to monitor the front or back
entrance to the premises.
This menu allows a user to turn chime mode on or off.
Only keypads programmed to sound the chime tone will
be heard when a zone programmed for chime is faulted.
The master user can set which zone are to be chime zones
via MENU 3-0-3. If no zones are programmed for chime
then chime mode will not activate.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [5].
A list of different areas will display on the keypad.
A1 Reception Area 
A2 Sales Dept
A3 Administration Dept
Press  OK or MENU
2. Use the [] and [] keys to select the area that you
want to turn chime mode on or off, then press [OK]
to select. Alternatively, you can enter the area
number that you want to turn chime mode on or
off, then press [OK]. The keypad will display the
following when chime mode is turned off:
Reception Area A1
Chime is OFF.
To turn ON, Press ON.
To Go Back Press OK
The keypad will display the following when chime
mode is turned on:
Reception Area A1
Chime is ON.
To turn OFF, Press OFF.
To Go Back Press OK

19Bosch Security Systems 10/22 BLCC615U
Solution 6000-IP User Guide
3. Press the [ON] key to turn chime mode on, or, press
[OFF] to turn chime mode off.
4. Press the [OK] key to exit.
i
Note
Holding down the 4 key on the keypad for 2 seconds
will also turn chime mode on and off.
Areas > Commands >
Chime Mode MENU 2-0-6
This menu allows you to program how the chime alert
behaves when a chime zone is triggered. There are four
different modes available: - Chime Always, Chime After ???
Seconds, Chime For ??? Seconds and Latching.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [0] + [6].
A list of different areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the chime mode for, then press
[OK] to select. Alternatively, you can enter the area
number that you want to program the name, then
press [OK].
The keypad will display the following:
Chime Mode A1
Chime For 000 Seconds
Press  OK to SAVE
3. Use the [] and [] keys to scroll through the
different options available. If the mode selected
requires you to enter a time then use the [] and
[] keys to move to the time field and then use the
[] and [] keys to scroll through the available time
options.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Areas > Area Properties >
Area Name MENU 2-1-0
This menu allows you to program the name for each
area. Each area name can be programmed with up to 20
characters. At factory default, only Area 1 is used. The
control panel can have a maximum of 8 independent areas
programmed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [0].
A list of different areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the name, then press [OK] to
select. Alternatively, you can enter the area number
that you want to program the name, then press
[OK].
The keypad will display the following:
Area Name A1
Security System
Press  OK to SAVE
3. Use the [] and [] keys to scroll the cursor left
and right across the area name text. Use the [] and
[] keys to scroll through the different characters
available. To clear all text from the cursor position
to the right, press the [OFF] key.
4. When the user name is complete, press [OK].
Areas > Area Properties >
Part Mode 1 Name MENU 2-1-6
This menu allows you to program a name for the part mode
1. Each area can have its own part mode 1 name if required.
Up to 20 characters can be entered to help explain the
behaviour of the area when it is armed in part mode 1. For
example, Downstairs all armed or Shed Disarmed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [6].
A list of different areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the part mode 1 name for, then
press [OK] to select. Alternatively, you can enter the
area number that you want to program the name,
then press [OK].
The keypad will display the following:
Part Mode 1 Name A1
Part 1 Area 1 Name
Press  OK to SAVE
3. Use the [] and [] keys to scroll the cursor left and
right across the name text. Use the [] and [] keys
to scroll through the different characters available.
To clear all text from the cursor position to the right,
press the [OFF] key.
4. When the name is complete, press [OK].
Areas > Area Properties >
Part Mode 2 Name MENU 2-1-7
This menu allows you to program a name for the part mode
2. Each area can have its own part mode 2 name if required.
Up to 20 characters can be entered to help explain the
behaviour of the area when it is armed in part mode 2. For
example, Downstairs all armed or Shed Disarmed.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [7].
A list of different areas will display on the keypad.

Solution 6000-IP
20 Bosch Security Systems 10/22 BLCC615U
User Guide
2. Use the [] and [] keys to select the area that you
want to program the part mode 2 name for, then
press [OK] to select. Alternatively, you can enter the
area number that you want to program the name,
then press [OK].
The keypad will display the following:
Part Mode 2 Name A1
Part 2 Area 1 Name
Press  OK to SAVE
3. Use the [] and [] keys to scroll the cursor left and
right across the name text. Use the [] and [] keys
to scroll through the different characters available.
To clear all text from the cursor position to the right,
press the [OFF] key.
4. When the name is complete, press [OK].
Areas > Area Properties >
Auto Arming MENU 2-1-8
This menu allows you to program which timezone will be
used by the system to auto arm and or, auto disarm the
system or area. Before setting this option you should make
sure the timezone has been configured in MENU 7-5-0.
Generally a timezone configured for auto arming should
be given a name that indicates its function.
The system has a maximum of 16 available timezones and
only one timezone can be programmed for each area. The
auto arm function can only be used to fully arm the area.
Only your installer can configure your system or area to
auto arm the area in part mode.
The area will automatically arm when the stop time in the
selected timezone is reached provided the day of the week
is also set.
The area will automatically arm when the stop time in the
selected timezone is reached provided the day of the week
is also set.
If auto disarming is not required then you should not set
the start time in the selected timezone. See MENU 7-5-0
for more information on configuring timezones.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [1] + [8].
A list of available areas will display on the keypad.
2. Use the [] and [] keys to select the area that you
want to program the auto arm time for, then press
[OK] to select. Alternatively, you can enter the area
number that you want to program, then press [OK].
The keypad will display the following:
Auto Arming A1
04 - TimeZone 4 Name
Press  0-9 OK to SAVE
3. Use the [] and [] keys to scroll through the list of
timezones until you reach the required one for the
chosen area.
4. Press [OK] to save and exit, or press [MENU] to exit
without saving.
Areas > Timers >
Exit Time MENU 2-8-0
This menu allows the master user to modify the exit timer
for the selected area. Each area in the system can have a
different exit time if required. The exit time is the amount
of time you have to leave the area once it has been turned
on. The keypad will sound an exit warning beep during
this time to let you and other users know that the area is
arming. An alarm cannot be triggered until the exit time
has expired.
Enter programming mode (PIN + MENU) then,
1. Enter [MENU] + [2] + [8] + [0].
A list of available areas will display on the keypad.
A1 Reception Area
A2 Sales Dept
A3 Administration Dept
Press  OK or MENU
2. Use the [] and [] keys to select the area that you
want to program the exit time for, then press [OK] to
select. Alternatively, you can enter the area number
that you want to program, then press [OK].
The keypad will display the following:
Exit Time A1
060 Seconds
Press 0-9 OK to SAVE
3. Use the numeric keys to enter the required time in
seconds and then press [OK]. Exit time can be set
from 0 to 255 seconds.
Areas > Timers >
Entry Time 1 MENU 2-8-1
This menu allows the master user to modify the entry timer
number 1 for the selected area. Each area in the system
can have a different entry time if required. Your installer
will have set up one or more entry zones per area on your
system and the zones may have been programmed to
follow either entry time 1 or entry time 2.
The entry time is the amount of time you have to turn your
alarm system off once the entry zone have been triggered
or opened.