Bowflex SelectTech 2080 User manual

Bowex™ SelectTech™ Weight Upgrade
Installation Guide 8022768.120119.A
Installation Guide
Refer to the Bowex™ SelectTech™ 2080 Barbell with Curl Bar Assembly/Owner’s Manual for complete safety
instructions.
Important Safety Instructions
This icon means a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Obey the following warnings:
Read and understand all warnings on the equipment.
• Carefully read and understand the Assembly and Owner’s Manual.
• Keep bystanders and children away from the product you are assembling at all times.
• Do not try to change the design or functionality of this machine. This could compromise the safety of this machine and will void
the warranty.
• Before each use, examine this machine for loose parts or signs of wear. Do not use if found in this condition. Contact Customer
Service (if inside US/Canada) or your local distributor (if outside US/Canada) for repair information.
• If replacement parts are necessary use only genuine Nautilus replacement parts and hardware. Failure to use genuine replace-
ment parts can cause a risk to users, keep the machine from operating correctly and void the warranty.
• Do not use until the machine has been fully assembled and inspected for correct performance in accordance with the Owner’s
Manual.
• The Barbell/Curl Bar is very heavy. If you are not using the optional Barbell Stand, put the Barbell/Curl Bar assembly directly
on the oor for best support.
• Do all assembly steps in the sequence given. Incorrect assembly can lead to injury.
If you need assistance, contact Customer Service (if inside US/Canada) or your local distributor (if outside US/Canada).
To nd your local international distributor, go to: www.nautilusinternational.com
Nautilus, Inc., 5415 Centerpoint Parkway, Groveport, OH 43125 USA, www.NautilusInc.com - Customer Service: North America [phone], csnls@nautilus.
com | Nautilus (Shanghai) Fitness Equipments Co, Ltd, Room 1701 &1702, 1018 Changning Road, Changning District, Shanghai, China 200042, www.nautilus.
cn - 86 21 6115 9668 | outside U.S. www.nautilusinternational.com | Printed in China | © 2019 Nautilus, Inc. | Bowex, the B logo and SelectTech are trademarks
owned by or licensed to Nautilus,Inc., which are registered or otherwise protected by common law in the United States and other countries. |
ORIGINAL DOCUMENT - ENGLISH VERSION ONLY
™
™
Tools
6 mm
#2
Parts
5-lb (2.27 kg) Weight Plates (qty 8)

1. Remove the Barbell and Weight Plates from the Base
Note: Before removing the Barbell, set the adjustment knobs to the lowest weight selection (9.1 kg /20 lbs.).
2. Loosen the Screws and Slide the Base End Shrouds Outward
NOTICE: Do not remove the screws. Align Shrouds with the outer set of screw holes in the Base Tubes to t the 120-lb
barbell conguration.
Note: Do not fully tighten screws. Shrouds should still slide.
Inner
Outer
6mm
X8
Weight: 18.1 kg (40 lbs)
Dimensions (Barbell set with Weight Upgrade plates): 158.6 cm L x 29.8 cm W x 32.2 cm H (62.4” x 11.7” x 12.7”)
Assembly

3. Move Lock Pin Actuators
NOTICE: Remove the Lock Pin Actuators and re-install in the inner set of screw holes in the Base End Shrouds to t the
120-lb barbell conguration.
#2
X4
Lock pin
actuator
(X2)
Inner
Outer
#2
X4
Lock pin
actuator
(X2)
4. Put Upgrade Weight Plates, Original Weight Plates and Barbell Assembly in the Base
In order to avoid possible serious injury, when placing the Weight Plates in the Base Assembly, be careful
to avoid ngers or hands being caught or pinched.
Note: Be sure that the Weight Plates are fully seated in the Base. Ensure there are no large gaps between Weight
Plates, and all weight plate tabs are aligned and locked together. Make sure the locking tab at the top of each
Base End Shroud is seated in the selection lip at the top of the back Weight Plate.
Locking tab
Upgrade
plates (4)
Upgrade
plates (4)

6. Final Inspection
Inspect your machine to ensure that all hardware is tight and components are properly assembled.
Do not use until the machine has been fully assembled and inspected for correct performance in accordance
with the Owner’s Manual.
5. Adjust Base End Shrouds
In order to avoid possible serious injury, when placing the Weight Plates in the Base Assembly, be careful
to avoid ngers or hands being caught or pinched.
Note: Push the shrouds inward. Tighten the inner screws. To tighten the outer screws, it may be necessary to remove
the Barbell and Weight Plates. This adjustment is important for proper function and easier re-racking. If the barbell
is difcult to re-rack after assembly, it may be necessary to repeat this process.
6mm
X2
6mm
X2
EN