Bowflex TreadClimber TC1000 User manual

1
BOWFLEX TREADCLIMBER
TC1000-TC3000-TC5000 ASSEMBLY MANUAL
(4 PIECE ASSEMBLY)

2
USE THIS ASSEMBLY MANUAL WHEN IT SHIPS IN 4 PIECES
(PARTLY DISASSEMBLED) - LIKE THIS DIAGRAM
1Console assembly
2-3 Uprights
4Base

3
INSTALLING STEPS
Step 6: INSTALLING THE UPRIGHTS
Locate the following for this step:
PARTS:
TreadClimber® Base & Treadle Assembly from Step 5.
One (1) Left Upright Support & Hydraulic Cylinder
One (1) Right Upright Support & Hydraulic Cylinder
HARDWARE:
Two (2) 5/16” x 1” Button Head Screws
On the base assembly screw a 5/16" x 1" button head
screw half way in on the outside of both the right and
left lower upright bracket (see Figure 6-1).
Place the left upright onto the left upright bracket
(see Figure 6-2), so it rests on the button head screw
(see Figure 6-3). Make sure the cylinder bracket is at
the top and pointing to rear.
Repeat this process on the right side.
Figure 6-1
Figure 6-2
Step 7: INSTALLING THE UPRIGHT JUNCTION COVERS AND COSMETIC PLUGS
Locate the following for this step:
PARTS:
TreadClimber® Base & Treadle Assembly from
Step 6.
Two (2) Plastic Upright Junction Covers
HARDWARE:
Four (4) Cosmetic Plugs
Place the plastic upright junction covers onto the
top of left upright support (see Figure 7-1).
Insert the cosmetic plugs (2 per side) into the holes
on the top, inside and outside of the left upright
support (see Figure 7-2).
Repeat this process on the right side.
Figure 6-3
Figure 7-1
Figure 7-2

4
INSTALLING STEPS
Step 8: INSTALLING THE CONSOLE/ HANDLEBAR ASSEMBLY
Locate the following for this step:
PARTS:
TreadClimber® Base & Treadle Assembly from
Step 7.
Console/Handlebar Assembly
HARDWARE:
Six (6) 5/16” x 1” Button Head Screws
Six (6) 5/16” Flat Washers SAE
TOOLS:
3/16” Hex Key (included)
With the help of another person, carefully lift
the console/handlebar assembly above the
tops of the upright supports. Feed the cable
down the top of the right upright support (see
Figure 8-1 & 8-1A). Make sure cable extends
through the bottom of the right upright.
Slide the brackets on the console/handlebar
assembly into the tops of the upright
supports—both sides at the same time. Be
careful when sliding the console/handlebar
assembly onto the uprights to avoid damaging
the electrical cable.
Attach the upright using (6) 5/16" x 1" button
head screws and (6) 5/16" flat washers SAE (3
per upright). Tighten with the provided 3/16"
hex key (see Figure 8-2).
Pull out the wire connector at the bottom of
the right upright support. Firmly connect the
electrical cable at the bottom of the right
upright support to the cable on the right side
of the base upright bracket (see Figure 8-3).
Figure 8-1
Figure 8-1A
Figure 8-2
Figure 8-3

5
INSTALLING STEPS
Step 9: SECURING THE CONSOLE/ HANDLEBAR ASSEMBLY
Locate the following for this step:
PARTS:
TreadClimber® Base & Treadle Assembly from
Step 8.
HARDWARE:
Six (6) 5/16” x 1” Button Head Screws NOTE:
Two (2) of the 5/16” x 1” Button Head
screws are already inserted into the bottom of
the right and left upright supports.
Six (6) 5/16” flat washer SAE
TOOLS:
3/16” Hex Key (included)
With the help of another person, carefully lift
the upright and remove the 5/16" x 1" button
head screw at the base of the support on the
right side. Carefully lower the upright on to the
upright bracket base, without damaging the
electrical cable. Repeat on the left side.
Attach the upright using (6) 5/16" x 1" button
head screws and (6) 5/16" flat washers SAE (3
per upright). Tighten with the provided 3/16"
hex key (see Figure 9-1). Repeat this process
on the remaining bracket.
NOTE: Tighten the front (2) screws first (1 per
upright) and then the (4) side screws (two per
outward side of upright). Tightening in this
order will result in a tighter fit.
Figure 9-1

6
INSTALLING STEPS
Step 10: ATTACHING THE HYDRAULIC CYLINDERS
Locate the following for this step:
PARTS:
TreadClimber® Base & Treadle Assembly from
Step 9.
HARDWARE:
Two (2) 5/16” x 1-1/2” Button Head Screws
Two (2) 5/16” Acorn Nuts
Two (2) 5/16” x 1” Button Head Screws
Two (2) 5/16” Flat Washers
TOOLS:
3/16” Hex Key (included)
9/16” Open End Wrench (included)
First bolt the dial end of the cylinders to the
uprights using (1) 5/16" x 1-1/2" button head
screw and (1) 5/16" acorn nut, per side.
Tighten with the provided 9/16" open end
wrench and 3/16" hex key (see Figure 10-1).
Make sure that the white arrows located on the
Workout Level Setting Dials at the top of the
Hydraulic Cylinders face the rear of the
machine where you can easily see them during
your workout.
Starting on the right side, pull the cylinder down
and place the eyelet on the Cylinder Stud
protruding from the treadles. Attach the
hydraulic cylinder using (1) 5/16" x 1" button
head screws and (1) 5/16" flat washers (see
Figure 10-2).
Repeat this process on the left side.
NOTE: If having difficulty placing hydraulic
cylinder(s) on treadle stud, loosen lower upright
screws, place cylinder on the stud and retighten
the upright screws.
Figure 10-1
Figure 10-2
Step 11: INSPECTING ASSEMBLY
11-1 Remove the protective plastic film from
the console face. Inspect all attachments you
have made thus far and tighten all bolts
securely before proceeding to Step 12.