BrandMotion SUTV-1040 User manual


SUTV-1040 3-12-2018 Page 1 of 12
UTV/Rockcrawler Quad Camera and DVR Monitor
(Kit #SUTV-1040)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Roll Bar Mounts (1.5” 1.75” 2”)
7” Quad Screen Monitor with DVR
IR Remote
Monitor Sun Shade
Left & Rear Side View Camera’s W/Cables
Front Camera W/Extension cable
Rear Infrared Camera W/Extension cable
SUTV-1040 Miscellaneous Parts Package
Tools & Supplies Needed:
Plastic Trim Removal Tool
Phillips Screwdriver
Center Punch/Scribe Tool
Power Drill
1/2” Drill Bit
Wire Ties
Soldering Iron & Solder (Recommended)
Tape or Heat Shrink Electrical Tubing


SUTV-1040 3-12-2018 Page 2 of 12
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions.
For additional assistance please call Brandmotion Technical Assistance at [phone] then dial 2.
Monitor bracket installation


SUTV-1040 3-12-2018 Page 3 of 12
Step 1: Using a small pick tool hold retaining clip in place and unscrew bolt and remove from universal
mount.
Brackets: The SUTV kit comes with 3 different sizes Monitor mounting brackets depending on your mounting
application.
Step 2: After choosing the proper size use supplied foam and apply to inner ring of bracket. Then follow
pictures to assemble bracket and mount


SUTV-1040 3-12-2018 Page 4 of 12


SUTV-1040 3-12-2018 Page 5 of 12


SUTV-1040 3-12-2018 Page 6 of 12


SUTV-1040 3-12-2018 Page 7 of 12
Left & Right-Side View Camera Installation: When installing side view cameras always make sure the red
arrow is facing upwards.
Step 1: Disassemble for mounting.


SUTV-1040 3-12-2018 Page 8 of 12
Step 2: Using rubber gasket find good mounting location and drill hole for routing harness.
Step 3: Align Camera to desired location and mount using Front & Rear mounting holes.
Step 4: Reassemble side view Camera. Follow your disassembly steps in reverse order


SUTV-1040 3-12-2018 Page 9 of 12
Front & Rear Camera Installation: For mounting the Front & Rear Cameras. Find a flat and level Mounting
location. Clean the area with Alcohol prep cleaner and mount to desired location. Mounting bracket can be
mounted ether direction as long as arrow faces up on Camera.
Front Camera: Front Camera Mounting.


SUTV-1040 3-12-2018 Page 10 of 12
Rear Camera: Rear Camera Mounting.


SUTV-1040 3-12-2018 Page 11 of 12
Vehicle Wiring: When wiring the kit on some applications there might not be access to some of the trigger
wires. (Left, Right turn signals, Reverse, etc.) When trigger wires are not available use toggle switch to trigger
input. Trigger wires are only needed for auto switching inputs. Can Manual switch video inputs on monitor.
SUTV Kit Wiring
Red ACC Power
Black Ground
Trigger 1 Video 1
Trigger 2 Video 2
Trigger 3 Video 3
Trigger 4 Video 4


SUTV-1040 3-12-2018 Page 12 of 12
Side View Camera Wiring: Each Side View Camera needs 12-volt accessory power and Chassis ground from
a clean non-painted surface. Also needs the composite video output cable ran to Video inputs on monitor. (1-
4). Can be hooked up to desired orientation on video screen. All outside connections please use supplied heat
shrink as to not VOID WARRANTY.
Front & Rear Camera wiring: Both Cameras needs 12-volt accessory power and Chassis ground from a
clean non-painted surface. Also needs the composite video output cable ran to Video inputs on monitor. (1-4).
Can be hooked up to desired orientation on video screen. All outside connections please use supplied heat
shrink as to not VOID WARRANTY.

REQUIRED VIDEO SETTING CHANGE: In order to properly use the supplied cameras, the
system must be changed from PAL to NTSC. Follow these steps to make the change.
1. Insert a 2032 sized battery into the included remote.
2. Press the ENT key in the center to bring up the login menu
3. Do not enter a password, and click OK
4. Select Record Set, and press ENT

5. Select PAL and change to NTSC
6. Select OK to confirm.
7. Press EXIT to close menus.
VIDEO PLAYER FIX: If you are unable to view you .avi movie of the recording, please
download this player. It will play the recordings no matter how long or short it is.
http://www.videolan.org/vlc/