BrandMotion 9002-8846 User manual

INSTALLATION INSTRUCTIONS
Jeep Wrangler Adjustable Rear Vision System with Mirror Display
2007 – Current (Kit # 9002-8846)
Items Included in the Kit
Camera
Chassis Harness
Zip lock bag with 15 Wire Ties & 3 Push Nuts
These Instructions
Display Mirror with Harness
Camera Extension Bracket
Required Tools & Supplies
T15 & T20 Torx Bits
7mm & 10mm Sockets
Phillips Screwdriver
Plastic Trim Removal Tool
Soldering Iron, Solder, & Heat Shrink Tubing
(RECOMMENDED) or T-taps as an alternate splicing
method
Electrical Tape
Please read so you do not VOID the warranty:
9002-8846 Instructions 9-17-19 Page 1 of 8 DM

INSTALLATION INSTRUCTIONS
If the camera harness is run through the center on the camera
bracket, it will cut the camera harness. This will void the
warranty on the camera.
Camera Power Instructions!: Only ONE of the red wires should be connected to ignition 12v+.
The other should be isolated with electrical tape before powering camera up. See step 26.
Camera Installation
1. Loosen lug nuts to remove the spare tire.
2. Slide Camera on studs placing harness end inside of
tire carrier. Do not run harness through the
camera bracket opening
.
3. Temporarily replace spare tire to check wheel
clearance to Camera. Adjust camera head to fit your
specific wheel. Bracket is shipped in factory wheel
configuration
Adjustment Bracket for Camera Clearance using Phillips
Screwdriver and 3/8” Wrench or Socket Drive
Note: Short Bracket has been designed for Factory offset
9002-8846 Instructions 9-17-19 Page 2 of 8 DM

INSTALLATION INSTRUCTIONS
wheels. Use the Long Bracket for wheels with larger offsets
4. Remove spare tire and slide (3) supplied Push Nuts
on the studs.
5. Plug the Camera connector into the Chassis Harness
connector, and insert RCA connector end of supplied
Chassis Harness through the rear gate vent behind
tire carrier.
6. Using a plastic trim removal tool, remove interior
panels on the inside of the rear gate.
7. Pull the harness through the rear gate openings
8. Use supplied Wire Ties to secure Chassis Harness to
existing harness.
9. Use supplied Wire Ties to secure Chassis Harness to
fabric factory wire cover. CAUTION: Leave enough
slack to allow the gate to open fully.
10. Use a T20 Torx bit to remove the subwoofer box. (If
9002-8846 Instructions 9-17-19 Page 3 of 8 DM

INSTALLATION INSTRUCTIONS
equipped)
11. Using a plastic trim removal tool, pry off rear seat
belt closeout.
12. Using a plastic trim removal tool, remove rear
access panel to expose 10mm bolt, and remove bolt.
13. Pull out subwoofer box slightly to gain access to run
Chassis Harness along existing harness
14. Pull back the carpet and continue running Chassis
Harness forward.
15. Run Chassis Harness under B-pillar cover to
passenger door sill. Use a plastic trim removal tool
to remove the (2) plastic push pins and remove
passenger sill plate/kick panel.
16. Remove rubber bin insert from top of the dash.
17. Remove 7mm bolt.
9002-8846 Instructions 9-17-19 Page 4 of 8 DM

INSTALLATION INSTRUCTIONS
18. Using a plastic trim removal tool, remove the
window switch panel.
19. Disconnect harness from window switches.
20. Remove 7mm bolt.
21. Remove driver's knee bolster cover.
22. Remove (2) 7mm bolts on both sides of the steering
column.
23. Remove center stack/cluster surround.
24. Remove glove box for access and run Chassis
Harness toward the center of the dash.
9002-8846 Instructions 9-17-19 Page 5 of 8 DM

INSTALLATION INSTRUCTIONS
25. Using a plastic trim removal tool, remove HVAC
panel.
26. Connecting Power
Splice Red power wire at the RCA to red 12v+ wire
on mirror harness OR splice red wire at chassis
harness connector to 12v+ in the back of the
vehicle. COVER UNUSED RED WIRE. Splice Black
Ground at rear to chassis ground. RECOMMENDED:
Use solder and cover with heat shrink tubing or use
T-taps as an alternate connection method.
Mirror Installation
1. Unplug factory mirror connector from back of mirror.
2. Use a T15 Torx bit to remove factory mirror and
slide the mirror upward off the mounting tab.
CAUTION: Do not twist mirror as windshield damage
could result.
3. Carefully install supplied Mirror by sliding it
downward on the mounting tab. CAUTION: Torque
supplied Mirror screw to 1.8 Nm (16 lb-in) and do
not exceed 2.2 Nm (19.5 lb-in).
4. Begin running 10-pin mirror connector end of Mirror
Harness to mirror by first removing IP access panel.
9002-8846 Instructions 9-17-19 Page 6 of 8 DM

INSTALLATION INSTRUCTIONS
5. Remove passenger side sun visor using a T15 Torx
bit.
6. Use a Phillips screwdriver to remove Phillips fastener
on upper-A pillar and remove pillar.
7. Remove lower A-pillar cover (no tools required).
8. Pull down right side of header panel.
9. Run supplied Mirror Harness to Mirror location.
10. Splice the red and Black wires located near the
10-pin connector on supplied Mirror Harness to the
below indicated wires of the factory mirror harness
using solder and cover with heat shrink tubing
(recommended).
Splice the green wire located near the 10-pin
connector on supplied Mirror Harness to the below
indicated wires of the factory mirror harness using
solder and cover with heat shrink tubing
(recommended).
16 Pin Position 9 - Reverse White/Gray to Green Wire
16 Pin Position 13 - 12v Ignition Pink/Yellow to Red Wire
16 Pin Position 8 – Ground Black to Black Wire
9002-8846 Instructions 9-17-19 Page 7 of 8 DM

INSTALLATION INSTRUCTIONS
16-pin Connector face
NOTE: If vehicle is not equipped with a power mirror
use this wire for reverse
.
In the factory wire harness located in the passenger foot
well, locate the White/Gray Reverse signal wire and
splice Green Reverse wire from supplied Mirror Harness
11. Connect supplied Mirror connector to supplied Mirror
Harness.
12. Connect the male RCA from the supplied chassis
harness to the female RCA on the supplied mirror
harness
13. Test the system. Start vehicle and shift into Reverse
in order to check that all connections were made
properly. If all of the connections are correct you will
see the camera image displayed on the display
mirror
14. Reassemble vehicle. Follow your disassembly steps
in reverse order, taking care not to bind the harness
wiring when reinstalling the trim.
9002-8846 Instructions 9-17-19 Page 8 of 8 DM