BrandMotion AVMS-3690 User manual

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 1 of 9
360º Vision System for Aftermarket Radio/Display
(Kit # AVMS-3690)
DUE TO THE COMPLEXITY OF THIS KIT
PROFESSIONAL INSTALLATION IS REQUIRED
CALIBRATION KIT IS REQUIRED FOR FINAL PROGRAMMING
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
360º camera module
Key box power/image buttons
Front camera w/grill mount and harness
2 side mount cameras w/pods and harnesses
2 video output RCA cables
Power/camera input harness
2 side camera templates
Mounting screws and gaskets
Rear license plate mounting bracket
These instructions
Wire strippers
Wire cutters
Electrical tape
Zip ties
Plastic panel removal tools
Screwdriver
7 mm socket
Drill
Large Uni-bit/drill bits
Hole saws
T-15 Torx
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
Section 1:
Front camera installation
1. Front camera is mounted in the grill aiming straight or at a 20º angle to the ground.
2. Mount camera in housing using the bracket and screws provided. (The white sticker is up on the
camera.)

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 2 of 9
3. Mount the housing using the provided screws to the grill and putting the caps in the holes to close
them.
4. Run the camera harness along the under hood covering, down the drive side hinge. Zip tie the harness
to the hinge so the harness will not kink or cut.
5. Run harness into the vehicle though the factory grommet in the drivers side firewall.
6. Route the camera harness to the location of the 360º module.
Section 2:
Side Mirror Camera installation
1. The inter door panel will have to be removed for installation of the side cameras.
2. Working on the driver side door. With the door closed, place the template sticker ( marked LHD ) on the
bottom side of the mirror with arrow aiming away from the vehicle. Perpendicular to the side of the
body. ( Do not go by mirror lines or angles .)

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 3 of 9

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 4 of 9

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 5 of 9
3. Make sure the template is to at least the middle to outer edge of the mirror. ( The camera needs to see
only 10% of the side of the vehicle and mainly the ground and objects next to the vehicle .)
4. Remove the door panel and the nuts or screws that are holding the mirror to the vehicle.
5. Place the mirror on a soft or padded surface and remove the glass from the mirror. ( Each vehicle is
different, but most are mounted by a center circle and will unclip from it .)
6. After the glass is removed, check to see if where the templates are placed there is clearance for the
camera and will not cut into anything in the mirror housing. ( If the template has to be moved make
sure to keep the arrow aiming the same way .)
7. Drill a hole in the bottom of the mirror using a hole saw or Uni-bit to the size on the template. Which is
1 1/8”

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 6 of 9
8. With the sticker still in place, drill the (2) mounting screw holes with a 1/16 drill bit. ( Do not go all the
way though .)
9. The side cameras, brackets and pods are labeled for right-RH and left-LH. Make sure to assemble them
correctly. Use caution not to loss the tiny screws to mount the cameras to the brackets and the
brackets to the pods.
10. Using the LH camera assembly, attach the foam gasket to the bottom side of the pod, lining up the
notch in the foam with the bump on the pod.
11. Adjust the side cameras so that at least 3 feet beyond the front and rear bumper is shown in the
image. Mount the 4 cameras in the acceptable range of positions, or the calibration of the images
might not be possible.
12. The Camera images can be viewed on the monitor by connecting the ECU to the Calibration KIT.
13. The view mode can be changed in order of Front, Rear, Left and Right by pressing the view button on
the Key box.
14. Remove the tape from the foam gasket and mount the camera pod to the mirror. Use the self-tapping
screws provided to mount the pods to the underside of the mirror. ( Do not over tighten the screws; it
may strip out the plastic.)

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 7 of 9
15. Route the camera cable though the mirror housing and out of the back mounting side of the mirror.
Make sure not to block any movement of the mirror glass or folding of the mirror.
16. Route the cable into the door and remount the mirror to the vehicle.
17. You will next pin the camera cable wires into the provided connecter. Inset the pins into the connecter
until they make a “snap” sound. Use the left side camera harness to match up where the pin locations
are. (See Diagram chart 1a. at end of instructions for all camera pin connections.)
18. Attach the camera cable to the harness and route though the door to the rubber boot. Secure the
harness to the factory wire harness with zip ties.
19. Route the harness out though the rubber boot into the vehicle. ( The vehicle might have a Molex or
plastic plug in the door of body, if so drill a hole in the plug if there is any room to, if not drill a hole
lower in the door just under the rubber boot and the same if the plug is in the body. Grommet and seal
any holes that might be drilled.)
20. Route the harness to the 360º module.
21. Reinstall the mirror glass into the mirror and reinstall the door panel.
22. Repeat the process on the passenger side door and then continue to the next section.
Section 3:
Rear camera installation
1. Mount Rear camera in the rear of the vehicle, in door or license plate housing. (The white sticker on
the camera is up.)
2. Mount camera to be able to see the ground and both outer edges of the vehicle.
3. Run harness to the front of the vehicle to where the 360º Main control module will be.
4. Zip tie the harness in place to make sure it does not rattle.

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 8 of 9
Section 4:
360º module installation
1. Connect the correct camera plugs to the 360º module. Front, rear, left side, right side, CVBS and CVBS
RV.
2. The CVRS output is video output controlled by the power on/off button to the system. It is connected
to the AUX video input on the aftermarket radio/display.
3. The CVRS RV output is video output when the accessory is powered on. It is connected to the back-up
camera input on the aftermarket radio/display.
4. If not done so yet connect the power harness to the 360º module. Wire up the power connections,
yellow is constant, red is accessory, black is ground, blue is reverse.
5. Do not mount the 360º module; you will need to get to it for calibration of the cameras.
6. Plug in the Key Box and mount to the right side of the steering column on the dash trim with the tape
provided. (Or any place that is flat and within reach of the driver.)
7. To turn on the system press the power button on the Key Box. To change camera views press the car
image button. A long press will show a full front view another long press will show a full rear view.
8. Place the vehicle into reverse to see the rear camera image on the screen. Or turn on screen to see
image. (Warning will be displayed on the screen until the unit is calibrated.)

! INSTALLATION!INSTRUCTIONS!
AVMS-3690 Instructions 9-2-16 Page 9 of 9
Diagram 1a.