BrandMotion 9002-7601 User manual

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines
Installation Instructions (Kit # 9002-7601)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in Kit:
Tools & Supplies Needed:
Chassis Harness
¼” Drill Bit
Camera mounted on license plate bracket
Multi-meter or computer-safe test light
Small bag containing:
Ground Eyelet (recommended)
Two license plate bolts [optional]
Soldering Iron
Alternate Camera Mount with Double-sided
Adhesive Foam
Solder (recommended) or T-Taps
Plastic trim removal tool
Instructions
Rubber Grommet or Silicone Caulk
(recommended)
Vehicle service manual (if needed)
Small sheet metal screws (recommended for
Alternative Camera Mount install)
Safety Precautions:
●Work in well ventilated area that is clear of obstructions.
●Secure vehicle with tire chucks in both front and rear of tires.
●Turn vehicle accessories OFF and ensure ignition key is in OFF position.
●Wear safety goggles and snug fitting clothes.
●Use tools only for their intended purpose and which are in good repair.
●Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. The latest full color
instructions can be accessed at www.brandmotion.com
9002-7601 Instructions 6-10-19 Page 1 of 5 KB

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines
Installation Instructions (Kit # 9002-7601)
Green Wire Connected
Green Wire Cut
White Wire Connected
White Wire Cut
No Park Lines
Park Lines
Front Camera
Rear Camera
Step 1: Select and Install Camera Bracket
Determine which of the two supplied camera mounting
methods you prefer.
License Plate Bracket
Alternate Camera Mount Bracket
Place camera in desired position to confirm fitment (Note:
Some states prohibit items blocking the license plate; check
local authorities to confirm legal status for your application).
If using License Plate Bracket, remove license plate.
Reattach license plate securing bracket behind.
If using Alternate Camera Mount Bracket, remove
camera from License Plate Bracket using supplied Allen
wrench. Attach camera to the Alternate Camera Mount
bracket and apply supplied self-adhesive foam to mount.
Use the Template included in the Installation Instruction
Overview to position the Alternate Camera Mount on vehicle
Clean vehicle surface to which mount is to be attached
and affix with self-adhesive foam. RECOMMENDED:
Permanent attachment using screws.
Step 2: Measure, mark, and drill ¼” hole for camera
harness. NOTE: If your vehicle has a liftgate panel/trunk
trim cover, it must be removed.
Step 3: Determine location of vehicle power and
ground. Using a vehicle specific service guide and/or specific
wiring diagram and a multi-meter or computer-safe test light,
locate which side of the vehicle contains reverse and Ground
wires (Chart A).
9002-7601 Instructions 6-10-19 Page 2 of 5 KB

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines
Installation Instructions (Kit # 9002-7601)
Chart A
Wire
Color
Polarity
Function
Description
Location
Red
12v +
Reverse
This lead will display
12 volt + when the
vehicle is in reverse
Commonly
found in
either
passenger or
drivers kick
panel
Black
(-)
Ground
Chassis ground
A ground
bolt is
commonly
found in the
front kick
panel area
with other
wires
attached.
Step 4: Splice the red
and black chassis
harness leads into the
corresponding vehicle
wires (Recommended:
Soldering or T-taps as
optional connection
method). Also
recommended is an eyelet
for the ground connection.
Step 5: Insert the connector end of the Camera
Harness through the hole you drilled. (RECOMMENDED:
Protect Camera Harness from sharp metal edges by applying
a small amount of silicone caulk or a rubber grommet to the
area that comes into contact with the metal).
Step 6: Route Camera Harness. Continue routing harness
to the side of the vehicle that supplies power and then
forward.
Step 7: Connect Camera Harness to supplied Chassis
Harness. The optimal location for this junction may occur at
the top of the liftgate or the inner edge of the trunk
depending on vehicle in which installation is in (Note: most
vehicles may already have existing wires passing through this
area; use this route if at all possible).
Step 8: Route Chassis Harness. It may be necessary to
remove sill plates, pillar covers, seat bottoms, side panels,
etc. In some cases even the seat belt bolts at the bottom of
the pillars must be removed (CAUTION: Any bolts removed
for safety devices must be reinstalled and tightened to
manufacturer’s specified torque specifications). Use a plastic
trim removal tool to avoid damage to trim pieces.
9002-7601 Instructions 6-10-19 Page 3 of 5 KB

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines
Installation Instructions (Kit # 9002-7601)
Step 9: Secure Camera Harness to existing vehicle
wiring. This will minimize the chance of binding or otherwise
damaging the harness (Recommended: Wire Ties or Electrical
Tape.)
Step 10: Connect Chassis Harness red wire reverse
wire and black to clean chassis ground.
Step 11: Install aftermarket display/ Navigation
display as per instructions (if required).
Step 12: Connect the male RCA from the Power
Harness to the “Camera IN” on the aftermarket
display/ Navigation display.
Note: Connection to female RCA connector shown.
Step 13: Test the system. Inspect that all connections are
proper and secure. Clear all loose items removed from the
area around the vehicle and turn ignition key ON to test
system.
Step 14: Adjust Camera angle (if necessary). Loosen
camera screw using supplied Allen wrench to aim the camera.
Tighten screw at desired adjustment.
Step 15: Reassemble vehicle. Follow your disassembly
steps in reverse order, taking care not to bind the harness
wiring when reinstalling.
OVERVIEW
REQUIRED CONNECTIONS
Wire
Color
Polarity
Function
Connection
Red
12v +
Reverse
Commonly found in kick panel
Black
-
Ground
Good chassis ground
1: Select and Install Camera Bracket. Choose License Plate Bracket or Alternate Camera Mount Bracket. Place camera in desired position to confirm
fitment (Note: Some states prohibit items blocking the license plate; check local authorities to confirm legal status for your specific application).
License Plate Bracket: Remove vehicle license plate. Reattach license plate securing bracket behind.
Alternate Camera Mount Bracket: Remove camera from License Plate Bracket using supplied Allen wrench. Attach camera to Alternate Camera Mount bracket
and apply supplied self-adhesive foam to mount. Use Template below to locate Alternate Camera mount on the vehicle: Clean vehicle surface and affix by exposing
self-adhesive foam. RECOMMENDED: Permanent attachment using small screws.
2: Measure, mark, and drill ¼” hole for camera harness.
3: Determine location of vehicle power and ground. Using a vehicle specific service guide and/or wiring diagram and a multi-meter or computer-safe test
light, locate which side of the vehicle contains wires into which you will need to tap for the Power Harness wiring (see Required Connections above).
9002-7601 Instructions 6-10-19 Page 4 of 5 KB

Dual Mount Universal Kit Aftermarket CMOS Camera with Optional Parking Gridlines
Installation Instructions (Kit # 9002-7601)
CAUTION: Once correct wires have been identified, turn Ignition key OFF and DO NOT turn key back ON until the install has been completed (Step 13).
4: Splice the red and black Power Harness leads into the corresponding vehicle wires (Recommended: Soldering or T-taps as optional connection
method; eyelet for the ground connection.)
5: Insert connector end of the Camera Harness through the hole you drilled.
6: Route Camera Harness. Continue routing harness to side of vehicle that supplies power and forward.
7: Connect Camera Harness to supplied Chassis Harness.
8: Route Chassis Harness.
9: Secure Camera Harness to existing vehicle wiring. (Recommended: Wire Ties or Electrical Tape.)
10: Connect Chassis Harness red wire to reverse and black to clean chassis ground.
11: Install aftermarket display/ Navigation display as per instructions (if required).
12: Connect Power Harness RCA to “Camera IN” on aftermarket display/ Navigation display.
13: Test the system.
14: Adjust Camera angle (if necessary). Loosen the camera screw using supplied Allen wrench to aim. Tighten screw at desired adjustment.
15: Reassemble vehicle. Follow disassembly steps in reverse order, taking care not to bind harness.
NOTE: This camera has grid lines or non grid lines and mirror image or non mirror image options:
Grid line options: Default setting is to display grid lines. To remove the grid line display, connect the two green wires near the end of the camera harness.
Display options: Default setting is mirror image display for rearward facing camera (rear view) installation. To change to non mirror image for forward facing
camera (front view) connect the two white wires near the end of the camera harness.
9002-7601 Instructions 6-10-19 Page 5 of 5 KB